| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: fix reconnection fail due to reserved tag allocation
We found a issue on production environment while using NVMe over RDMA,
admin_q reconnect failed forever while remote target and network is ok.
After dig into it, we found it may caused by a ABBA deadlock due to tag
allocation. In my case, the tag was hold by a keep alive request
waiting inside admin_q, as we quiesced admin_q while reset ctrl, so the
request maked as idle and will not process before reset success. As
fabric_q shares tagset with admin_q, while reconnect remote target, we
need a tag for connect command, but the only one reserved tag was held
by keep alive command which waiting inside admin_q. As a result, we
failed to reconnect admin_q forever. In order to fix this issue, I
think we should keep two reserved tags for admin queue. |
| In the Linux kernel, the following vulnerability has been resolved:
lib: alloc_tag_module_unload must wait for pending kfree_rcu calls
Ben Greear reports following splat:
------------[ cut here ]------------
net/netfilter/nf_nat_core.c:1114 module nf_nat func:nf_nat_register_fn has 256 allocated at module unload
WARNING: CPU: 1 PID: 10421 at lib/alloc_tag.c:168 alloc_tag_module_unload+0x22b/0x3f0
Modules linked in: nf_nat(-) btrfs ufs qnx4 hfsplus hfs minix vfat msdos fat
...
Hardware name: Default string Default string/SKYBAY, BIOS 5.12 08/04/2020
RIP: 0010:alloc_tag_module_unload+0x22b/0x3f0
codetag_unload_module+0x19b/0x2a0
? codetag_load_module+0x80/0x80
nf_nat module exit calls kfree_rcu on those addresses, but the free
operation is likely still pending by the time alloc_tag checks for leaks.
Wait for outstanding kfree_rcu operations to complete before checking
resolves this warning.
Reproducer:
unshare -n iptables-nft -t nat -A PREROUTING -p tcp
grep nf_nat /proc/allocinfo # will list 4 allocations
rmmod nft_chain_nat
rmmod nf_nat # will WARN.
[akpm@linux-foundation.org: add comment] |
| In the Linux kernel, the following vulnerability has been resolved:
debugfs: fix wait/cancellation handling during remove
Ben Greear further reports deadlocks during concurrent debugfs
remove while files are being accessed, even though the code in
question now uses debugfs cancellations. Turns out that despite
all the review on the locking, we missed completely that the
logic is wrong: if the refcount hits zero we can finish (and
need not wait for the completion), but if it doesn't we have
to trigger all the cancellations. As written, we can _never_
get into the loop triggering the cancellations. Fix this, and
explain it better while at it. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Define the __io_aw() hook as mmiowb()
Commit fb24ea52f78e0d595852e ("drivers: Remove explicit invocations of
mmiowb()") remove all mmiowb() in drivers, but it says:
"NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation."
The mmio in radeon_ring_commit() is protected by a mutex rather than a
spinlock, but in the mutex fastpath it behaves similar to spinlock. We
can add mmiowb() calls in the radeon driver but the maintainer says he
doesn't like such a workaround, and radeon is not the only example of
mutex protected mmio.
So we should extend the mmiowb tracking system from spinlock to mutex,
and maybe other locking primitives. This is not easy and error prone, so
we solve it in the architectural code, by simply defining the __io_aw()
hook as mmiowb(). And we no longer need to override queued_spin_unlock()
so use the generic definition.
Without this, we get such an error when run 'glxgears' on weak ordering
architectures such as LoongArch:
radeon 0000:04:00.0: ring 0 stalled for more than 10324msec
radeon 0000:04:00.0: ring 3 stalled for more than 10240msec
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000001f412 last fence id 0x000000000001f414 on ring 3)
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000000f940 last fence id 0x000000000000f941 on ring 0)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix racy may inline data check in dio write
syzbot reports that the following warning from ext4_iomap_begin()
triggers as of the commit referenced below:
if (WARN_ON_ONCE(ext4_has_inline_data(inode)))
return -ERANGE;
This occurs during a dio write, which is never expected to encounter
an inode with inline data. To enforce this behavior,
ext4_dio_write_iter() checks the current inline state of the inode
and clears the MAY_INLINE_DATA state flag to either fall back to
buffered writes, or enforce that any other writers in progress on
the inode are not allowed to create inline data.
The problem is that the check for existing inline data and the state
flag can span a lock cycle. For example, if the ilock is originally
locked shared and subsequently upgraded to exclusive, another writer
may have reacquired the lock and created inline data before the dio
write task acquires the lock and proceeds.
The commit referenced below loosens the lock requirements to allow
some forms of unaligned dio writes to occur under shared lock, but
AFAICT the inline data check was technically already racy for any
dio write that would have involved a lock cycle. Regardless, lift
clearing of the state bit to the same lock critical section that
checks for preexisting inline data on the inode to close the race. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: scarlett2: Add missing mutex lock around get meter levels
As scarlett2_meter_ctl_get() uses meter_level_map[], the data_mutex
should be locked while accessing it. |
| In the Linux kernel, the following vulnerability has been resolved:
cfg80211: fix management registrations locking
The management registrations locking was broken, the list was
locked for each wdev, but cfg80211_mgmt_registrations_update()
iterated it without holding all the correct spinlocks, causing
list corruption.
Rather than trying to fix it with fine-grained locking, just
move the lock to the wiphy/rdev (still need the list on each
wdev), we already need to hold the wdev lock to change it, so
there's no contention on the lock in any case. This trivially
fixes the bug since we hold one wdev's lock already, and now
will hold the lock that protects all lists. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ks8851: Handle softirqs at the end of IRQ thread to fix hang
The ks8851_irq() thread may call ks8851_rx_pkts() in case there are
any packets in the MAC FIFO, which calls netif_rx(). This netif_rx()
implementation is guarded by local_bh_disable() and local_bh_enable().
The local_bh_enable() may call do_softirq() to run softirqs in case
any are pending. One of the softirqs is net_rx_action, which ultimately
reaches the driver .start_xmit callback. If that happens, the system
hangs. The entire call chain is below:
ks8851_start_xmit_par from netdev_start_xmit
netdev_start_xmit from dev_hard_start_xmit
dev_hard_start_xmit from sch_direct_xmit
sch_direct_xmit from __dev_queue_xmit
__dev_queue_xmit from __neigh_update
__neigh_update from neigh_update
neigh_update from arp_process.constprop.0
arp_process.constprop.0 from __netif_receive_skb_one_core
__netif_receive_skb_one_core from process_backlog
process_backlog from __napi_poll.constprop.0
__napi_poll.constprop.0 from net_rx_action
net_rx_action from __do_softirq
__do_softirq from call_with_stack
call_with_stack from do_softirq
do_softirq from __local_bh_enable_ip
__local_bh_enable_ip from netif_rx
netif_rx from ks8851_irq
ks8851_irq from irq_thread_fn
irq_thread_fn from irq_thread
irq_thread from kthread
kthread from ret_from_fork
The hang happens because ks8851_irq() first locks a spinlock in
ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...)
and with that spinlock locked, calls netif_rx(). Once the execution
reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again
which attempts to claim the already locked spinlock again, and the
hang happens.
Move the do_softirq() call outside of the spinlock protected section
of ks8851_irq() by disabling BHs around the entire spinlock protected
section of ks8851_irq() handler. Place local_bh_enable() outside of
the spinlock protected section, so that it can trigger do_softirq()
without the ks8851_par.c ks8851_lock_par() spinlock being held, and
safely call ks8851_start_xmit_par() without attempting to lock the
already locked spinlock.
Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable()
now, replace netif_rx() with __netif_rx() which is not duplicating the
local_bh_disable()/local_bh_enable() calls. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: Convert spinlock to mutex to lock evl workqueue
drain_workqueue() cannot be called safely in a spinlocked context due to
possible task rescheduling. In the multi-task scenario, calling
queue_work() while drain_workqueue() will lead to a Call Trace as
pushing a work on a draining workqueue is not permitted in spinlocked
context.
Call Trace:
<TASK>
? __warn+0x7d/0x140
? __queue_work+0x2b2/0x440
? report_bug+0x1f8/0x200
? handle_bug+0x3c/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? __queue_work+0x2b2/0x440
queue_work_on+0x28/0x30
idxd_misc_thread+0x303/0x5a0 [idxd]
? __schedule+0x369/0xb40
? __pfx_irq_thread_fn+0x10/0x10
? irq_thread+0xbc/0x1b0
irq_thread_fn+0x21/0x70
irq_thread+0x102/0x1b0
? preempt_count_add+0x74/0xa0
? __pfx_irq_thread_dtor+0x10/0x10
? __pfx_irq_thread+0x10/0x10
kthread+0x103/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The current implementation uses a spinlock to protect event log workqueue
and will lead to the Call Trace due to potential task rescheduling.
To address the locking issue, convert the spinlock to mutex, allowing
the drain_workqueue() to be called in a safe mutex-locked context.
This change ensures proper synchronization when accessing the event log
workqueue, preventing potential Call Trace and improving the overall
robustness of the code. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/vmalloc: combine all TLB flush operations of KASAN shadow virtual address into one operation
When compiling kernel source 'make -j $(nproc)' with the up-and-running
KASAN-enabled kernel on a 256-core machine, the following soft lockup is
shown:
watchdog: BUG: soft lockup - CPU#28 stuck for 22s! [kworker/28:1:1760]
CPU: 28 PID: 1760 Comm: kworker/28:1 Kdump: loaded Not tainted 6.10.0-rc5 #95
Workqueue: events drain_vmap_area_work
RIP: 0010:smp_call_function_many_cond+0x1d8/0xbb0
Code: 38 c8 7c 08 84 c9 0f 85 49 08 00 00 8b 45 08 a8 01 74 2e 48 89 f1 49 89 f7 48 c1 e9 03 41 83 e7 07 4c 01 e9 41 83 c7 03 f3 90 <0f> b6 01 41 38 c7 7c 08 84 c0 0f 85 d4 06 00 00 8b 45 08 a8 01 75
RSP: 0018:ffffc9000cb3fb60 EFLAGS: 00000202
RAX: 0000000000000011 RBX: ffff8883bc4469c0 RCX: ffffed10776e9949
RDX: 0000000000000002 RSI: ffff8883bb74ca48 RDI: ffffffff8434dc50
RBP: ffff8883bb74ca40 R08: ffff888103585dc0 R09: ffff8884533a1800
R10: 0000000000000004 R11: ffffffffffffffff R12: ffffed1077888d39
R13: dffffc0000000000 R14: ffffed1077888d38 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8883bc400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005577b5c8d158 CR3: 0000000004850000 CR4: 0000000000350ef0
Call Trace:
<IRQ>
? watchdog_timer_fn+0x2cd/0x390
? __pfx_watchdog_timer_fn+0x10/0x10
? __hrtimer_run_queues+0x300/0x6d0
? sched_clock_cpu+0x69/0x4e0
? __pfx___hrtimer_run_queues+0x10/0x10
? srso_return_thunk+0x5/0x5f
? ktime_get_update_offsets_now+0x7f/0x2a0
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
? hrtimer_interrupt+0x2ca/0x760
? __sysvec_apic_timer_interrupt+0x8c/0x2b0
? sysvec_apic_timer_interrupt+0x6a/0x90
</IRQ>
<TASK>
? asm_sysvec_apic_timer_interrupt+0x16/0x20
? smp_call_function_many_cond+0x1d8/0xbb0
? __pfx_do_kernel_range_flush+0x10/0x10
on_each_cpu_cond_mask+0x20/0x40
flush_tlb_kernel_range+0x19b/0x250
? srso_return_thunk+0x5/0x5f
? kasan_release_vmalloc+0xa7/0xc0
purge_vmap_node+0x357/0x820
? __pfx_purge_vmap_node+0x10/0x10
__purge_vmap_area_lazy+0x5b8/0xa10
drain_vmap_area_work+0x21/0x30
process_one_work+0x661/0x10b0
worker_thread+0x844/0x10e0
? srso_return_thunk+0x5/0x5f
? __kthread_parkme+0x82/0x140
? __pfx_worker_thread+0x10/0x10
kthread+0x2a5/0x370
? __pfx_kthread+0x10/0x10
ret_from_fork+0x30/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Debugging Analysis:
1. The following ftrace log shows that the lockup CPU spends too much
time iterating vmap_nodes and flushing TLB when purging vm_area
structures. (Some info is trimmed).
kworker: funcgraph_entry: | drain_vmap_area_work() {
kworker: funcgraph_entry: | mutex_lock() {
kworker: funcgraph_entry: 1.092 us | __cond_resched();
kworker: funcgraph_exit: 3.306 us | }
... ...
kworker: funcgraph_entry: | flush_tlb_kernel_range() {
... ...
kworker: funcgraph_exit: # 7533.649 us | }
... ...
kworker: funcgraph_entry: 2.344 us | mutex_unlock();
kworker: funcgraph_exit: $ 23871554 us | }
The drain_vmap_area_work() spends over 23 seconds.
There are 2805 flush_tlb_kernel_range() calls in the ftrace log.
* One is called in __purge_vmap_area_lazy().
* Others are called by purge_vmap_node->kasan_release_vmalloc.
purge_vmap_node() iteratively releases kasan vmalloc
allocations and flushes TLB for each vmap_area.
- [Rough calculation] Each flush_tlb_kernel_range() runs
about 7.5ms.
-- 2804 * 7.5ms = 21.03 seconds.
-- That's why a soft lock is triggered.
2. Extending the soft lockup time can work around the issue (For example,
# echo
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: protect device queue against concurrent access
In dasd_profile_start() the amount of requests on the device queue are
counted. The access to the device queue is unprotected against
concurrent access. With a lot of parallel I/O, especially with alias
devices enabled, the device queue can change while dasd_profile_start()
is accessing the queue. In the worst case this leads to a kernel panic
due to incorrect pointer accesses.
Fix this by taking the device lock before accessing the queue and
counting the requests. Additionally the check for a valid profile data
pointer can be done earlier to avoid unnecessary locking in a hot path. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/rdmavt: add lock to call to rvt_error_qp to prevent a race condition
The documentation of the function rvt_error_qp says both r_lock and s_lock
need to be held when calling that function. It also asserts using lockdep
that both of those locks are held. However, the commit I referenced in
Fixes accidentally makes the call to rvt_error_qp in rvt_ruc_loopback no
longer covered by r_lock. This results in the lockdep assertion failing
and also possibly in a race condition. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/ast: Fix soft lockup
There is a while-loop in ast_dp_set_on_off() that could lead to
infinite-loop. This is because the register, VGACRI-Dx, checked in
this API is a scratch register actually controlled by a MCU, named
DPMCU, in BMC.
These scratch registers are protected by scu-lock. If suc-lock is not
off, DPMCU can not update these registers and then host will have soft
lockup due to never updated status.
DPMCU is used to control DP and relative registers to handshake with
host's VGA driver. Even the most time-consuming task, DP's link
training, is less than 100ms. 200ms should be enough. |
| In the Linux kernel, the following vulnerability has been resolved:
stackdepot: fix stack_depot_save_flags() in NMI context
Per documentation, stack_depot_save_flags() was meant to be usable from
NMI context if STACK_DEPOT_FLAG_CAN_ALLOC is unset. However, it still
would try to take the pool_lock in an attempt to save a stack trace in the
current pool (if space is available).
This could result in deadlock if an NMI is handled while pool_lock is
already held. To avoid deadlock, only try to take the lock in NMI context
and give up if unsuccessful.
The documentation is fixed to clearly convey this. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: Fix error cleanup path in nfsd_rename()
Commit a8b0026847b8 ("rename(): avoid a deadlock in the case of parents
having no common ancestor") added an error bail out path. However this
path does not drop the remount protection that has been acquired. Fix
the cleanup path to properly drop the remount protection. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Fix potential AB/BA lock with buffer_mutex and mmap_lock
syzbot caught a potential deadlock between the PCM
runtime->buffer_mutex and the mm->mmap_lock. It was brought by the
recent fix to cover the racy read/write and other ioctls, and in that
commit, I overlooked a (hopefully only) corner case that may take the
revert lock, namely, the OSS mmap. The OSS mmap operation
exceptionally allows to re-configure the parameters inside the OSS
mmap syscall, where mm->mmap_mutex is already held. Meanwhile, the
copy_from/to_user calls at read/write operations also take the
mm->mmap_lock internally, hence it may lead to a AB/BA deadlock.
A similar problem was already seen in the past and we fixed it with a
refcount (in commit b248371628aa). The former fix covered only the
call paths with OSS read/write and OSS ioctls, while we need to cover
the concurrent access via both ALSA and OSS APIs now.
This patch addresses the problem above by replacing the buffer_mutex
lock in the read/write operations with a refcount similar as we've
used for OSS. The new field, runtime->buffer_accessing, keeps the
number of concurrent read/write operations. Unlike the former
buffer_mutex protection, this protects only around the
copy_from/to_user() calls; the other codes are basically protected by
the PCM stream lock. The refcount can be a negative, meaning blocked
by the ioctls. If a negative value is seen, the read/write aborts
with -EBUSY. In the ioctl side, OTOH, they check this refcount, too,
and set to a negative value for blocking unless it's already being
accessed. |
| In the Linux kernel, the following vulnerability has been resolved:
driver core: Fix wait_for_device_probe() & deferred_probe_timeout interaction
Mounting NFS rootfs was timing out when deferred_probe_timeout was
non-zero [1]. This was because ip_auto_config() initcall times out
waiting for the network interfaces to show up when
deferred_probe_timeout was non-zero. While ip_auto_config() calls
wait_for_device_probe() to make sure any currently running deferred
probe work or asynchronous probe finishes, that wasn't sufficient to
account for devices being deferred until deferred_probe_timeout.
Commit 35a672363ab3 ("driver core: Ensure wait_for_device_probe() waits
until the deferred_probe_timeout fires") tried to fix that by making
sure wait_for_device_probe() waits for deferred_probe_timeout to expire
before returning.
However, if wait_for_device_probe() is called from the kernel_init()
context:
- Before deferred_probe_initcall() [2], it causes the boot process to
hang due to a deadlock.
- After deferred_probe_initcall() [3], it blocks kernel_init() from
continuing till deferred_probe_timeout expires and beats the point of
deferred_probe_timeout that's trying to wait for userspace to load
modules.
Neither of this is good. So revert the changes to
wait_for_device_probe().
[1] - https://lore.kernel.org/lkml/TYAPR01MB45443DF63B9EF29054F7C41FD8C60@TYAPR01MB4544.jpnprd01.prod.outlook.com/
[2] - https://lore.kernel.org/lkml/YowHNo4sBjr9ijZr@dev-arch.thelio-3990X/
[3] - https://lore.kernel.org/lkml/Yo3WvGnNk3LvLb7R@linutronix.de/ |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: dlmfs: fix error handling of user_dlm_destroy_lock
When user_dlm_destroy_lock failed, it didn't clean up the flags it set
before exit. For USER_LOCK_IN_TEARDOWN, if this function fails because of
lock is still in used, next time when unlink invokes this function, it
will return succeed, and then unlink will remove inode and dentry if lock
is not in used(file closed), but the dlm lock is still linked in dlm lock
resource, then when bast come in, it will trigger a panic due to
user-after-free. See the following panic call trace. To fix this,
USER_LOCK_IN_TEARDOWN should be reverted if fail. And also error should
be returned if USER_LOCK_IN_TEARDOWN is set to let user know that unlink
fail.
For the case of ocfs2_dlm_unlock failure, besides USER_LOCK_IN_TEARDOWN,
USER_LOCK_BUSY is also required to be cleared. Even though spin lock is
released in between, but USER_LOCK_IN_TEARDOWN is still set, for
USER_LOCK_BUSY, if before every place that waits on this flag,
USER_LOCK_IN_TEARDOWN is checked to bail out, that will make sure no flow
waits on the busy flag set by user_dlm_destroy_lock(), then we can
simplely revert USER_LOCK_BUSY when ocfs2_dlm_unlock fails. Fix
user_dlm_cluster_lock() which is the only function not following this.
[ 941.336392] (python,26174,16):dlmfs_unlink:562 ERROR: unlink
004fb0000060000b5a90b8c847b72e1, error -16 from destroy
[ 989.757536] ------------[ cut here ]------------
[ 989.757709] kernel BUG at fs/ocfs2/dlmfs/userdlm.c:173!
[ 989.757876] invalid opcode: 0000 [#1] SMP
[ 989.758027] Modules linked in: ksplice_2zhuk2jr_ib_ipoib_new(O)
ksplice_2zhuk2jr(O) mptctl mptbase xen_netback xen_blkback xen_gntalloc
xen_gntdev xen_evtchn cdc_ether usbnet mii ocfs2 jbd2 rpcsec_gss_krb5
auth_rpcgss nfsv4 nfsv3 nfs_acl nfs fscache lockd grace ocfs2_dlmfs
ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs bnx2fc
fcoe libfcoe libfc scsi_transport_fc sunrpc ipmi_devintf bridge stp llc
rds_rdma rds bonding ib_sdp ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad
rdma_cm ib_cm iw_cm falcon_lsm_serviceable(PE) falcon_nf_netcontain(PE)
mlx4_vnic falcon_kal(E) falcon_lsm_pinned_13402(E) mlx4_ib ib_sa ib_mad
ib_core ib_addr xenfs xen_privcmd dm_multipath iTCO_wdt iTCO_vendor_support
pcspkr sb_edac edac_core i2c_i801 lpc_ich mfd_core ipmi_ssif i2c_core ipmi_si
ipmi_msghandler
[ 989.760686] ioatdma sg ext3 jbd mbcache sd_mod ahci libahci ixgbe dca ptp
pps_core vxlan udp_tunnel ip6_udp_tunnel megaraid_sas mlx4_core crc32c_intel
be2iscsi bnx2i cnic uio cxgb4i cxgb4 cxgb3i libcxgbi ipv6 cxgb3 mdio
libiscsi_tcp qla4xxx iscsi_boot_sysfs libiscsi scsi_transport_iscsi wmi
dm_mirror dm_region_hash dm_log dm_mod [last unloaded:
ksplice_2zhuk2jr_ib_ipoib_old]
[ 989.761987] CPU: 10 PID: 19102 Comm: dlm_thread Tainted: P OE
4.1.12-124.57.1.el6uek.x86_64 #2
[ 989.762290] Hardware name: Oracle Corporation ORACLE SERVER
X5-2/ASM,MOTHERBOARD,1U, BIOS 30350100 06/17/2021
[ 989.762599] task: ffff880178af6200 ti: ffff88017f7c8000 task.ti:
ffff88017f7c8000
[ 989.762848] RIP: e030:[<ffffffffc07d4316>] [<ffffffffc07d4316>]
__user_dlm_queue_lockres.part.4+0x76/0x80 [ocfs2_dlmfs]
[ 989.763185] RSP: e02b:ffff88017f7cbcb8 EFLAGS: 00010246
[ 989.763353] RAX: 0000000000000000 RBX: ffff880174d48008 RCX:
0000000000000003
[ 989.763565] RDX: 0000000000120012 RSI: 0000000000000003 RDI:
ffff880174d48170
[ 989.763778] RBP: ffff88017f7cbcc8 R08: ffff88021f4293b0 R09:
0000000000000000
[ 989.763991] R10: ffff880179c8c000 R11: 0000000000000003 R12:
ffff880174d48008
[ 989.764204] R13: 0000000000000003 R14: ffff880179c8c000 R15:
ffff88021db7a000
[ 989.764422] FS: 0000000000000000(0000) GS:ffff880247480000(0000)
knlGS:ffff880247480000
[ 989.764685] CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 989.764865] CR2: ffff8000007f6800 CR3: 0000000001ae0000 CR4:
0000000000042660
[ 989.765081] Stack:
[ 989.765167] 00000000000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: fix lockdep splat in qdisc_tree_reduce_backlog()
qdisc_tree_reduce_backlog() is called with the qdisc lock held,
not RTNL.
We must use qdisc_lookup_rcu() instead of qdisc_lookup()
syzbot reported:
WARNING: suspicious RCU usage
6.1.74-syzkaller #0 Not tainted
-----------------------------
net/sched/sch_api.c:305 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
3 locks held by udevd/1142:
#0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:306 [inline]
#0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:747 [inline]
#0: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: net_tx_action+0x64a/0x970 net/core/dev.c:5282
#1: ffff888171861108 (&sch->q.lock){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:350 [inline]
#1: ffff888171861108 (&sch->q.lock){+.-.}-{2:2}, at: net_tx_action+0x754/0x970 net/core/dev.c:5297
#2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:306 [inline]
#2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:747 [inline]
#2: ffffffff87c729a0 (rcu_read_lock){....}-{1:2}, at: qdisc_tree_reduce_backlog+0x84/0x580 net/sched/sch_api.c:792
stack backtrace:
CPU: 1 PID: 1142 Comm: udevd Not tainted 6.1.74-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
Call Trace:
<TASK>
[<ffffffff85b85f14>] __dump_stack lib/dump_stack.c:88 [inline]
[<ffffffff85b85f14>] dump_stack_lvl+0x1b1/0x28f lib/dump_stack.c:106
[<ffffffff85b86007>] dump_stack+0x15/0x1e lib/dump_stack.c:113
[<ffffffff81802299>] lockdep_rcu_suspicious+0x1b9/0x260 kernel/locking/lockdep.c:6592
[<ffffffff84f0054c>] qdisc_lookup+0xac/0x6f0 net/sched/sch_api.c:305
[<ffffffff84f037c3>] qdisc_tree_reduce_backlog+0x243/0x580 net/sched/sch_api.c:811
[<ffffffff84f5b78c>] pfifo_tail_enqueue+0x32c/0x4b0 net/sched/sch_fifo.c:51
[<ffffffff84fbcf63>] qdisc_enqueue include/net/sch_generic.h:833 [inline]
[<ffffffff84fbcf63>] netem_dequeue+0xeb3/0x15d0 net/sched/sch_netem.c:723
[<ffffffff84eecab9>] dequeue_skb net/sched/sch_generic.c:292 [inline]
[<ffffffff84eecab9>] qdisc_restart net/sched/sch_generic.c:397 [inline]
[<ffffffff84eecab9>] __qdisc_run+0x249/0x1e60 net/sched/sch_generic.c:415
[<ffffffff84d7aa96>] qdisc_run+0xd6/0x260 include/net/pkt_sched.h:125
[<ffffffff84d85d29>] net_tx_action+0x7c9/0x970 net/core/dev.c:5313
[<ffffffff85e002bd>] __do_softirq+0x2bd/0x9bd kernel/softirq.c:616
[<ffffffff81568bca>] invoke_softirq kernel/softirq.c:447 [inline]
[<ffffffff81568bca>] __irq_exit_rcu+0xca/0x230 kernel/softirq.c:700
[<ffffffff81568ae9>] irq_exit_rcu+0x9/0x20 kernel/softirq.c:712
[<ffffffff85b89f52>] sysvec_apic_timer_interrupt+0x42/0x90 arch/x86/kernel/apic/apic.c:1107
[<ffffffff85c00ccb>] asm_sysvec_apic_timer_interrupt+0x1b/0x20 arch/x86/include/asm/idtentry.h:656 |
| In the Linux kernel, the following vulnerability has been resolved:
md/dm-raid: don't call md_reap_sync_thread() directly
Currently md_reap_sync_thread() is called from raid_message() directly
without holding 'reconfig_mutex', this is definitely unsafe because
md_reap_sync_thread() can change many fields that is protected by
'reconfig_mutex'.
However, hold 'reconfig_mutex' here is still problematic because this
will cause deadlock, for example, commit 130443d60b1b ("md: refactor
idle/frozen_sync_thread() to fix deadlock").
Fix this problem by using stop_sync_thread() to unregister sync_thread,
like md/raid did. |
