| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: synchronize atomic write aborts
To fix a race condition between atomic write aborts, I use the inode
lock and make COW inode to be re-usable thoroughout the whole
atomic file inode lifetime. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dp: Drop aux devices together with DP controller
Using devres to depopulate the aux bus made sure that upon a probe
deferral the EDP panel device would be destroyed and recreated upon next
attempt.
But the struct device which the devres is tied to is the DPUs
(drm_dev->dev), which may be happen after the DP controller is torn
down.
Indications of this can be seen in the commonly seen EDID-hexdump full
of zeros in the log, or the occasional/rare KASAN fault where the
panel's attempt to read the EDID information causes a use after free on
DP resources.
It's tempting to move the devres to the DP controller's struct device,
but the resources used by the device(s) on the aux bus are explicitly
torn down in the error path. The KASAN-reported use-after-free also
remains, as the DP aux "module" explicitly frees its devres-allocated
memory in this code path.
As such, explicitly depopulate the aux bus in the error path, and in the
component unbind path, to avoid these issues.
Patchwork: https://patchwork.freedesktop.org/patch/542163/ |
| In the Linux kernel, the following vulnerability has been resolved:
iavf: use internal state to free traffic IRQs
If the system tries to close the netdev while iavf_reset_task() is
running, __LINK_STATE_START will be cleared and netif_running() will
return false in iavf_reinit_interrupt_scheme(). This will result in
iavf_free_traffic_irqs() not being called and a leak as follows:
[7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0'
[7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0
is shown when pci_disable_msix() is later called. Fix by using the
internal adapter state. The traffic IRQs will always exist if
state == __IAVF_RUNNING. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: wcd-mbhc-v2: fix resource leaks on component remove
The MBHC resources must be released on component probe failure and
removal so can not be tied to the lifetime of the component device.
This is specifically needed to allow probe deferrals of the sound card
which otherwise fails when reprobing the codec component:
snd-sc8280xp sound: ASoC: failed to instantiate card -517
genirq: Flags mismatch irq 299. 00002001 (mbhc sw intr) vs. 00002001 (mbhc sw intr)
wcd938x_codec audio-codec: Failed to request mbhc interrupts -16
wcd938x_codec audio-codec: mbhc initialization failed
wcd938x_codec audio-codec: ASoC: error at snd_soc_component_probe on audio-codec: -16
snd-sc8280xp sound: ASoC: failed to instantiate card -16 |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: reject negative ifindex
Recent changes in net-next (commit 759ab1edb56c ("net: store netdevs
in an xarray")) refactored the handling of pre-assigned ifindexes
and let syzbot surface a latent problem in ovs. ovs does not validate
ifindex, making it possible to create netdev ports with negative
ifindex values. It's easy to repro with YNL:
$ ./cli.py --spec netlink/specs/ovs_datapath.yaml \
--do new \
--json '{"upcall-pid": 1, "name":"my-dp"}'
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
$ ip link show
-65536: some-port0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 7a:48:21:ad:0b:fb brd ff:ff:ff:ff:ff:ff
...
Validate the inputs. Now the second command correctly returns:
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
lib.ynl.NlError: Netlink error: Numerical result out of range
nl_len = 108 (92) nl_flags = 0x300 nl_type = 2
error: -34 extack: {'msg': 'integer out of range', 'unknown': [[type:4 len:36] b'\x0c\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x0c\x00\x03\x00\xff\xff\xff\x7f\x00\x00\x00\x00\x08\x00\x01\x00\x08\x00\x00\x00'], 'bad-attr': '.ifindex'}
Accept 0 since it used to be silently ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix workqueue leak on bind errors
Make sure to destroy the workqueue also in case of early errors during
bind (e.g. a subcomponent failing to bind).
Since commit c3b790ea07a1 ("drm: Manage drm_mode_config_init with
drmm_") the mode config will be freed when the drm device is released
also when using the legacy interface, but add an explicit cleanup for
consistency and to facilitate backporting.
Patchwork: https://patchwork.freedesktop.org/patch/525093/ |
| In the Linux kernel, the following vulnerability has been resolved:
HSI: omap_ssi: Fix refcount leak in ssi_probe
When returning or breaking early from a
for_each_available_child_of_node() loop, we need to explicitly call
of_node_put() on the child node to possibly release the node. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: zynq: Fix refcount leak in zynq_early_slcr_init
of_find_compatible_node() returns a node pointer with refcount incremented,
we should use of_node_put() on error path.
Add missing of_node_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5-cache: fix a deadlock in r5l_exit_log()
Commit b13015af94cf ("md/raid5-cache: Clear conf->log after finishing
work") introduce a new problem:
// caller hold reconfig_mutex
r5l_exit_log
flush_work(&log->disable_writeback_work)
r5c_disable_writeback_async
wait_event
/*
* conf->log is not NULL, and mddev_trylock()
* will fail, wait_event() can never pass.
*/
conf->log = NULL
Fix this problem by setting 'config->log' to NULL before wake_up() as it
used to be, so that wait_event() from r5c_disable_writeback_async() can
exist. In the meantime, move forward md_unregister_thread() so that
null-ptr-deref this commit fixed can still be fixed. |
| In the Linux kernel, the following vulnerability has been resolved:
io-wq: Fix memory leak in worker creation
If the CPU mask allocation for a node fails, then the memory allocated for
the 'io_wqe' struct of the current node doesn't get freed on the error
handling path, since it has not yet been added to the 'wqes' array.
This was spotted when fuzzing v6.1-rc1 with Syzkaller:
BUG: memory leak
unreferenced object 0xffff8880093d5000 (size 1024):
comm "syz-executor.2", pid 7701, jiffies 4295048595 (age 13.900s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000cb463369>] __kmem_cache_alloc_node+0x18e/0x720
[<00000000147a3f9c>] kmalloc_node_trace+0x2a/0x130
[<000000004e107011>] io_wq_create+0x7b9/0xdc0
[<00000000c38b2018>] io_uring_alloc_task_context+0x31e/0x59d
[<00000000867399da>] __io_uring_add_tctx_node.cold+0x19/0x1ba
[<000000007e0e7a79>] io_uring_setup.cold+0x1b80/0x1dce
[<00000000b545e9f6>] __x64_sys_io_uring_setup+0x5d/0x80
[<000000008a8a7508>] do_syscall_64+0x5d/0x90
[<000000004ac08bec>] entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
usb-storage: alauda: Fix uninit-value in alauda_check_media()
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: qcom-hw: Fix memory leak in qcom_cpufreq_hw_read_lut()
If "cpu_dev" fails to get opp table in qcom_cpufreq_hw_read_lut(),
the program will return, resulting in "table" resource is not released. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: kexec: Fix memory leak of fdt buffer
This is reported by kmemleak detector:
unreferenced object 0xff60000082864000 (size 9588):
comm "kexec", pid 146, jiffies 4294900634 (age 64.788s)
hex dump (first 32 bytes):
d0 0d fe ed 00 00 12 ed 00 00 00 48 00 00 11 40 ...........H...@
00 00 00 28 00 00 00 11 00 00 00 02 00 00 00 00 ...(............
backtrace:
[<00000000f95b17c4>] kmemleak_alloc+0x34/0x3e
[<00000000b9ec8e3e>] kmalloc_order+0x9c/0xc4
[<00000000a95cf02e>] kmalloc_order_trace+0x34/0xb6
[<00000000f01e68b4>] __kmalloc+0x5c2/0x62a
[<000000002bd497b2>] kvmalloc_node+0x66/0xd6
[<00000000906542fa>] of_kexec_alloc_and_setup_fdt+0xa6/0x6ea
[<00000000e1166bde>] elf_kexec_load+0x206/0x4ec
[<0000000036548e09>] kexec_image_load_default+0x40/0x4c
[<0000000079fbe1b4>] sys_kexec_file_load+0x1c4/0x322
[<0000000040c62c03>] ret_from_syscall+0x0/0x2
In elf_kexec_load(), a buffer is allocated via kvmalloc() to store fdt.
While it's not freed back to system when kexec kernel is reloaded or
unloaded. Then memory leak is caused. Fix it by introducing riscv
specific function arch_kimage_file_post_load_cleanup(), and freeing the
buffer there. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix potential UAF in smb2_close_cached_fid()
find_or_create_cached_dir() could grab a new reference after kref_put()
had seen the refcount drop to zero but before cfid_list_lock is acquired
in smb2_close_cached_fid(), leading to use-after-free.
Switch to kref_put_lock() so cfid_release() is called with
cfid_list_lock held, closing that gap. |
| In the Linux kernel, the following vulnerability has been resolved:
l2tp: Avoid possible recursive deadlock in l2tp_tunnel_register()
When a file descriptor of pppol2tp socket is passed as file descriptor
of UDP socket, a recursive deadlock occurs in l2tp_tunnel_register().
This situation is reproduced by the following program:
int main(void)
{
int sock;
struct sockaddr_pppol2tp addr;
sock = socket(AF_PPPOX, SOCK_DGRAM, PX_PROTO_OL2TP);
if (sock < 0) {
perror("socket");
return 1;
}
addr.sa_family = AF_PPPOX;
addr.sa_protocol = PX_PROTO_OL2TP;
addr.pppol2tp.pid = 0;
addr.pppol2tp.fd = sock;
addr.pppol2tp.addr.sin_family = PF_INET;
addr.pppol2tp.addr.sin_port = htons(0);
addr.pppol2tp.addr.sin_addr.s_addr = inet_addr("192.168.0.1");
addr.pppol2tp.s_tunnel = 1;
addr.pppol2tp.s_session = 0;
addr.pppol2tp.d_tunnel = 0;
addr.pppol2tp.d_session = 0;
if (connect(sock, (const struct sockaddr *)&addr, sizeof(addr)) < 0) {
perror("connect");
return 1;
}
return 0;
}
This program causes the following lockdep warning:
============================================
WARNING: possible recursive locking detected
6.2.0-rc5-00205-gc96618275234 #56 Not tainted
--------------------------------------------
repro/8607 is trying to acquire lock:
ffff8880213c8130 (sk_lock-AF_PPPOX){+.+.}-{0:0}, at: l2tp_tunnel_register+0x2b7/0x11c0
but task is already holding lock:
ffff8880213c8130 (sk_lock-AF_PPPOX){+.+.}-{0:0}, at: pppol2tp_connect+0xa82/0x1a30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(sk_lock-AF_PPPOX);
lock(sk_lock-AF_PPPOX);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by repro/8607:
#0: ffff8880213c8130 (sk_lock-AF_PPPOX){+.+.}-{0:0}, at: pppol2tp_connect+0xa82/0x1a30
stack backtrace:
CPU: 0 PID: 8607 Comm: repro Not tainted 6.2.0-rc5-00205-gc96618275234 #56
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x100/0x178
__lock_acquire.cold+0x119/0x3b9
? lockdep_hardirqs_on_prepare+0x410/0x410
lock_acquire+0x1e0/0x610
? l2tp_tunnel_register+0x2b7/0x11c0
? lock_downgrade+0x710/0x710
? __fget_files+0x283/0x3e0
lock_sock_nested+0x3a/0xf0
? l2tp_tunnel_register+0x2b7/0x11c0
l2tp_tunnel_register+0x2b7/0x11c0
? sprintf+0xc4/0x100
? l2tp_tunnel_del_work+0x6b0/0x6b0
? debug_object_deactivate+0x320/0x320
? lockdep_init_map_type+0x16d/0x7a0
? lockdep_init_map_type+0x16d/0x7a0
? l2tp_tunnel_create+0x2bf/0x4b0
? l2tp_tunnel_create+0x3c6/0x4b0
pppol2tp_connect+0x14e1/0x1a30
? pppol2tp_put_sk+0xd0/0xd0
? aa_sk_perm+0x2b7/0xa80
? aa_af_perm+0x260/0x260
? bpf_lsm_socket_connect+0x9/0x10
? pppol2tp_put_sk+0xd0/0xd0
__sys_connect_file+0x14f/0x190
__sys_connect+0x133/0x160
? __sys_connect_file+0x190/0x190
? lockdep_hardirqs_on+0x7d/0x100
? ktime_get_coarse_real_ts64+0x1b7/0x200
? ktime_get_coarse_real_ts64+0x147/0x200
? __audit_syscall_entry+0x396/0x500
__x64_sys_connect+0x72/0xb0
do_syscall_64+0x38/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
This patch fixes the issue by getting/creating the tunnel before
locking the pppol2tp socket. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix xid leak in cifs_copy_file_range()
If the file is used by swap, before return -EOPNOTSUPP, should
free the xid, otherwise, the xid will be leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: Make port I/O string accessors actually work
Fix port I/O string accessors such as `insb', `outsb', etc. which use
the physical PCI port I/O address rather than the corresponding memory
mapping to get at the requested location, which in turn breaks at least
accesses made by our parport driver to a PCIe parallel port such as:
PCI parallel port detected: 1415:c118, I/O at 0x1000(0x1008), IRQ 20
parport0: PC-style at 0x1000 (0x1008), irq 20, using FIFO [PCSPP,TRISTATE,COMPAT,EPP,ECP]
causing a memory access fault:
Unable to handle kernel access to user memory without uaccess routines at virtual address 0000000000001008
Oops [#1]
Modules linked in:
CPU: 1 PID: 350 Comm: cat Not tainted 6.0.0-rc2-00283-g10d4879f9ef0-dirty #23
Hardware name: SiFive HiFive Unmatched A00 (DT)
epc : parport_pc_fifo_write_block_pio+0x266/0x416
ra : parport_pc_fifo_write_block_pio+0xb4/0x416
epc : ffffffff80542c3e ra : ffffffff80542a8c sp : ffffffd88899fc60
gp : ffffffff80fa2700 tp : ffffffd882b1e900 t0 : ffffffd883d0b000
t1 : ffffffffff000002 t2 : 4646393043330a38 s0 : ffffffd88899fcf0
s1 : 0000000000001000 a0 : 0000000000000010 a1 : 0000000000000000
a2 : ffffffd883d0a010 a3 : 0000000000000023 a4 : 00000000ffff8fbb
a5 : ffffffd883d0a001 a6 : 0000000100000000 a7 : ffffffc800000000
s2 : ffffffffff000002 s3 : ffffffff80d28880 s4 : ffffffff80fa1f50
s5 : 0000000000001008 s6 : 0000000000000008 s7 : ffffffd883d0a000
s8 : 0004000000000000 s9 : ffffffff80dc1d80 s10: ffffffd8807e4000
s11: 0000000000000000 t3 : 00000000000000ff t4 : 393044410a303930
t5 : 0000000000001000 t6 : 0000000000040000
status: 0000000200000120 badaddr: 0000000000001008 cause: 000000000000000f
[<ffffffff80543212>] parport_pc_compat_write_block_pio+0xfe/0x200
[<ffffffff8053bbc0>] parport_write+0x46/0xf8
[<ffffffff8050530e>] lp_write+0x158/0x2d2
[<ffffffff80185716>] vfs_write+0x8e/0x2c2
[<ffffffff80185a74>] ksys_write+0x52/0xc2
[<ffffffff80185af2>] sys_write+0xe/0x16
[<ffffffff80003770>] ret_from_syscall+0x0/0x2
---[ end trace 0000000000000000 ]---
For simplicity address the problem by adding PCI_IOBASE to the physical
address requested in the respective wrapper macros only, observing that
the raw accessors such as `__insb', `__outsb', etc. are not supposed to
be used other than by said macros. Remove the cast to `long' that is no
longer needed on `addr' now that it is used as an offset from PCI_IOBASE
and add parentheses around `addr' needed for predictable evaluation in
macro expansion. No need to make said adjustments in separate changes
given that current code is gravely broken and does not ever work. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix reference state management for synchronous callbacks
Currently, verifier verifies callback functions (sync and async) as if
they will be executed once, (i.e. it explores execution state as if the
function was being called once). The next insn to explore is set to
start of subprog and the exit from nested frame is handled using
curframe > 0 and prepare_func_exit. In case of async callback it uses a
customized variant of push_stack simulating a kind of branch to set up
custom state and execution context for the async callback.
While this approach is simple and works when callback really will be
executed only once, it is unsafe for all of our current helpers which
are for_each style, i.e. they execute the callback multiple times.
A callback releasing acquired references of the caller may do so
multiple times, but currently verifier sees it as one call inside the
frame, which then returns to caller. Hence, it thinks it released some
reference that the cb e.g. got access through callback_ctx (register
filled inside cb from spilled typed register on stack).
Similarly, it may see that an acquire call is unpaired inside the
callback, so the caller will copy the reference state of callback and
then will have to release the register with new ref_obj_ids. But again,
the callback may execute multiple times, but the verifier will only
account for acquired references for a single symbolic execution of the
callback, which will cause leaks.
Note that for async callback case, things are different. While currently
we have bpf_timer_set_callback which only executes it once, even for
multiple executions it would be safe, as reference state is NULL and
check_reference_leak would force program to release state before
BPF_EXIT. The state is also unaffected by analysis for the caller frame.
Hence async callback is safe.
Since we want the reference state to be accessible, e.g. for pointers
loaded from stack through callback_ctx's PTR_TO_STACK, we still have to
copy caller's reference_state to callback's bpf_func_state, but we
enforce that whatever references it adds to that reference_state has
been released before it hits BPF_EXIT. This requires introducing a new
callback_ref member in the reference state to distinguish between caller
vs callee references. Hence, check_reference_leak now errors out if it
sees we are in callback_fn and we have not released callback_ref refs.
Since there can be multiple nested callbacks, like frame 0 -> cb1 -> cb2
etc. we need to also distinguish between whether this particular ref
belongs to this callback frame or parent, and only error for our own, so
we store state->frameno (which is always non-zero for callbacks).
In short, callbacks can read parent reference_state, but cannot mutate
it, to be able to use pointers acquired by the caller. They must only
undo their changes (by releasing their own acquired_refs before
BPF_EXIT) on top of caller reference_state before returning (at which
point the caller and callback state will match anyway, so no need to
copy it back to caller). |
| In the Linux kernel, the following vulnerability has been resolved:
uio: uio_dmem_genirq: Fix missing unlock in irq configuration
Commit b74351287d4b ("uio: fix a sleep-in-atomic-context bug in
uio_dmem_genirq_irqcontrol()") started calling disable_irq() without
holding the spinlock because it can sleep. However, that fix introduced
another bug: if interrupt is already disabled and a new disable request
comes in, then the spinlock is not unlocked:
root@localhost:~# printf '\x00\x00\x00\x00' > /dev/uio0
root@localhost:~# printf '\x00\x00\x00\x00' > /dev/uio0
root@localhost:~# [ 14.851538] BUG: scheduling while atomic: bash/223/0x00000002
[ 14.851991] Modules linked in: uio_dmem_genirq uio myfpga(OE) bochs drm_vram_helper drm_ttm_helper ttm drm_kms_helper drm snd_pcm ppdev joydev psmouse snd_timer snd e1000fb_sys_fops syscopyarea parport sysfillrect soundcore sysimgblt input_leds pcspkr i2c_piix4 serio_raw floppy evbug qemu_fw_cfg mac_hid pata_acpi ip_tables x_tables autofs4 [last unloaded: parport_pc]
[ 14.854206] CPU: 0 PID: 223 Comm: bash Tainted: G OE 6.0.0-rc7 #21
[ 14.854786] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
[ 14.855664] Call Trace:
[ 14.855861] <TASK>
[ 14.856025] dump_stack_lvl+0x4d/0x67
[ 14.856325] dump_stack+0x14/0x1a
[ 14.856583] __schedule_bug.cold+0x4b/0x5c
[ 14.856915] __schedule+0xe81/0x13d0
[ 14.857199] ? idr_find+0x13/0x20
[ 14.857456] ? get_work_pool+0x2d/0x50
[ 14.857756] ? __flush_work+0x233/0x280
[ 14.858068] ? __schedule+0xa95/0x13d0
[ 14.858307] ? idr_find+0x13/0x20
[ 14.858519] ? get_work_pool+0x2d/0x50
[ 14.858798] schedule+0x6c/0x100
[ 14.859009] schedule_hrtimeout_range_clock+0xff/0x110
[ 14.859335] ? tty_write_room+0x1f/0x30
[ 14.859598] ? n_tty_poll+0x1ec/0x220
[ 14.859830] ? tty_ldisc_deref+0x1a/0x20
[ 14.860090] schedule_hrtimeout_range+0x17/0x20
[ 14.860373] do_select+0x596/0x840
[ 14.860627] ? __kernel_text_address+0x16/0x50
[ 14.860954] ? poll_freewait+0xb0/0xb0
[ 14.861235] ? poll_freewait+0xb0/0xb0
[ 14.861517] ? rpm_resume+0x49d/0x780
[ 14.861798] ? common_interrupt+0x59/0xa0
[ 14.862127] ? asm_common_interrupt+0x2b/0x40
[ 14.862511] ? __uart_start.isra.0+0x61/0x70
[ 14.862902] ? __check_object_size+0x61/0x280
[ 14.863255] core_sys_select+0x1c6/0x400
[ 14.863575] ? vfs_write+0x1c9/0x3d0
[ 14.863853] ? vfs_write+0x1c9/0x3d0
[ 14.864121] ? _copy_from_user+0x45/0x70
[ 14.864526] do_pselect.constprop.0+0xb3/0xf0
[ 14.864893] ? do_syscall_64+0x6d/0x90
[ 14.865228] ? do_syscall_64+0x6d/0x90
[ 14.865556] __x64_sys_pselect6+0x76/0xa0
[ 14.865906] do_syscall_64+0x60/0x90
[ 14.866214] ? syscall_exit_to_user_mode+0x2a/0x50
[ 14.866640] ? do_syscall_64+0x6d/0x90
[ 14.866972] ? do_syscall_64+0x6d/0x90
[ 14.867286] ? do_syscall_64+0x6d/0x90
[ 14.867626] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...] stripped
[ 14.872959] </TASK>
('myfpga' is a simple 'uio_dmem_genirq' driver I wrote to test this)
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
introduced, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(). Then commit 34cb27528398 ("UIO: Fix concurrency
issue"), which was only applied to "uio_pdrv_genirq", ended up making them
a little different. That commit, among other things, changed disable_irq()
to disable_irq_nosync() in the implementation of irqcontrol(). The
motivation there was to avoid a deadlock between irqcontrol() and
handler(), since it added a spinlock in the irq handler, and disable_irq()
waits for the completion of the irq handler.
By changing disable_irq() to disable_irq_nosync() in irqcontrol(), we also
avoid the sleeping-whil
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/kprobes: Fix null pointer reference in arch_prepare_kprobe()
I found a null pointer reference in arch_prepare_kprobe():
# echo 'p cmdline_proc_show' > kprobe_events
# echo 'p cmdline_proc_show+16' >> kprobe_events
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000050bfc
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 122 Comm: sh Not tainted 6.0.0-rc3-00007-gdcf8e5633e2e #10
NIP: c000000000050bfc LR: c000000000050bec CTR: 0000000000005bdc
REGS: c0000000348475b0 TRAP: 0300 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 88002444 XER: 20040006
CFAR: c00000000022d100 DAR: 0000000000000000 DSISR: 40000000 IRQMASK: 0
...
NIP arch_prepare_kprobe+0x10c/0x2d0
LR arch_prepare_kprobe+0xfc/0x2d0
Call Trace:
0xc0000000012f77a0 (unreliable)
register_kprobe+0x3c0/0x7a0
__register_trace_kprobe+0x140/0x1a0
__trace_kprobe_create+0x794/0x1040
trace_probe_create+0xc4/0xe0
create_or_delete_trace_kprobe+0x2c/0x80
trace_parse_run_command+0xf0/0x210
probes_write+0x20/0x40
vfs_write+0xfc/0x450
ksys_write+0x84/0x140
system_call_exception+0x17c/0x3a0
system_call_vectored_common+0xe8/0x278
--- interrupt: 3000 at 0x7fffa5682de0
NIP: 00007fffa5682de0 LR: 0000000000000000 CTR: 0000000000000000
REGS: c000000034847e80 TRAP: 3000 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 900000000280f033 <SF,HV,VEC,VSX,EE,PR,FP,ME,IR,DR,RI,LE> CR: 44002408 XER: 00000000
The address being probed has some special:
cmdline_proc_show: Probe based on ftrace
cmdline_proc_show+16: Probe for the next instruction at the ftrace location
The ftrace-based kprobe does not generate kprobe::ainsn::insn, it gets
set to NULL. In arch_prepare_kprobe() it will check for:
...
prev = get_kprobe(p->addr - 1);
preempt_enable_no_resched();
if (prev && ppc_inst_prefixed(ppc_inst_read(prev->ainsn.insn))) {
...
If prev is based on ftrace, 'ppc_inst_read(prev->ainsn.insn)' will occur
with a null pointer reference. At this point prev->addr will not be a
prefixed instruction, so the check can be skipped.
Check if prev is ftrace-based kprobe before reading 'prev->ainsn.insn'
to fix this problem.
[mpe: Trim oops] |
