| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: timer: don't re-enter an instance callback that is still running
The userspace-driven timer (utimer) TRIGGER ioctl calls
snd_timer_interrupt() directly with no serialization, so two threads
triggering the same utimer can run snd_timer_interrupt() on one
snd_timer concurrently.
snd_timer_process_callbacks() drops timer->lock around each instance
callback and marks the in-flight callback with the single
SNDRV_TIMER_IFLG_CALLBACK bit; snd_timer_close_locked() waits on that
bit to drain an in-flight callback before freeing the instance. The bit
cannot represent two concurrent callbacks: when a second interrupt
re-queues an instance whose callback is still running, both run at once,
the first to finish clears the bit, and the close-path drain then frees
the instance (and its callback_data) while the other callback is still
live - a use-after-free reachable by any user able to open
/dev/snd/timer, both via a user timer instance and via a sequencer queue
timer bound to the utimer.
snd_timer_interrupt() sets IFLG_CALLBACK before dropping timer->lock, so
a concurrent interrupt already observes it under the lock. Skip
re-queuing an instance (and its slaves) to the ack/sack list while its
callback is in flight; the accumulated pticks are delivered on the next
tick, so no event is lost. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/bios: range check LFP Data Block panel_type2
While the panel_type from LFP Data Block is range checked, panel_type2
is not. Add a few helpers for range checking, and use them to not only
check panel_type2, but also improve clarity and correctness in the panel
type selection.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
v2:
- Fix commit message typo (Michał)
- Add is_panel_type_pnp() (Ville)
(cherry picked from commit c9ebe5d2f25729d6cfbbb1235d640bf67f9275df) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Hold a dma-buf reference for imported BOs
An imported dma-buf BO is created as a ttm_bo_type_sg BO whose
reservation object is the exporter's dma_buf->resv. The importer,
however, only takes a dma-buf reference after a successful
dma_buf_dynamic_attach(). Until then nothing keeps the exporter alive,
so if the exporter is freed while the BO still references its resv, a
later access to that resv is a use-after-free:
Oops: general protection fault, probably for non-canonical address
0x6b6b6b6b6b6b6b9c
Workqueue: ttm ttm_bo_delayed_delete [ttm]
RIP: 0010:mutex_can_spin_on_owner+0x3f/0xc0
This can be reached on two paths:
- dma_buf_dynamic_attach() fails, or
- ttm_bo_init_reserved() fails during BO creation.
In both cases the BO already has bo->base.resv pointing at the exporter
resv, and sg BOs are always torn down via ttm_bo_delayed_delete(), which
locks bo->base.resv asynchronously - potentially after the exporter has
been freed.
Take the dma-buf reference in xe_bo_init_locked(), before
ttm_bo_init_reserved(), so it also covers a creation failure there, and
release it in xe_ttm_bo_destroy(). The reference is held for the whole
BO lifetime, keeping the shared resv alive on every path.
v2:
- Reworked the fix to avoid creating the imported sg BO before
dma_buf_dynamic_attach() succeeds.
- Attach with importer_priv == NULL and make invalidate_mappings ignore
incomplete imports.
v3:
- Dropped the xe-side reordering approach since importer_priv must be
valid when dma_buf_dynamic_attach() publishes the attachment.
- Per Christian's suggestion on the v1 thread, keyed the check on
import_attach rather than removing the sg guard entirely.
- Fixes both xe and amdgpu in a single TTM patch.
v4:
- Moved import_attach check to after dma_resv_copy_fences() so fences
are copied before returning for successful imports (Thomas).
- Removed exporter-alive claim from commit message (Thomas).
v5:
- Add drm/xe patch to keep imported sg BOs off the LRU before attach
succeeds; the TTM fix alone is not sufficient for xe if the BO is
already LRU-visible. (Thomas)
v4 patch:
https://patchwork.freedesktop.org/patch/736663/?series=169129&rev=2
- Patch 1 (drm/ttm) carries Christian's Reviewed-by from v4.
v6:
- Reworked the fix based on Thomas' suggestion. Instead of the TTM resv
individualization (v1-v5) plus the xe off-LRU/placement handling (v5),
just hold a dma-buf reference for the imported BO lifetime so the
shared resv can never be freed while the BO still references it.
Single xe patch, no TTM change. (Thomas)
- Take the reference in xe_bo_init_locked() before ttm_bo_init_reserved()
so a TTM creation failure is covered too (Thomas).
- Dropped the v5 series (drm/ttm + drm/xe off-LRU); the off-LRU approach
also regressed in CI BAT via ttm_bo_pipeline_gutting() creating a ghost
BO that outlived the exporter.
Link to v5: https://patchwork.freedesktop.org/series/169984/
v7:
- Move changelog above --- so it stays in the commit message.
- Reorder changelog entries oldest-to-newest. (Thomas)
(cherry picked from commit 3516f3fae6be35642f8f06f8a218da6425c0306a) |
| The Admin Safety Guard — Login Security, Limit Logins, 2FA & Brute Force Protection WordPress plugin before 1.4.0 does not perform any capability check on one of its REST API endpoints, allowing unauthenticated attackers to retrieve the full list of registered users including their usernames, email addresses, roles, and two-factor authentication enrollment status. |
| The WP Directory Kit WordPress plugin before 1.5.5 does not perform authorization or nonce checks on one of its authenticated AJAX actions, allowing any authenticated user such as a Subscriber to retrieve stored contact messages and associated user data belonging to other users. |
| The WPC Order Tip for WooCommerce WordPress plugin before 3.3.1 does not perform authorisation or nonce checks in one of its reporting features, allowing unauthenticated attackers to retrieve sensitive order data belonging to any customer of the store, such as billing names, order IDs and statuses, fee amounts and order dates. |
| The InfiniteWP Client WordPress plugin before 1.13.6 does not properly verify the site-connection state and the authenticity of requests to its remote-management endpoint on WordPress Multisite installations, allowing unauthenticated attackers to bind their own key, hijack an administrator session, and take over the entire network, leading to remote code execution. |
| The PiWeb Cancel order / Refund request for WooCommerce WordPress plugin before 1.3.4.34 does not have authorization or ownership checks when adding the contents of a previous order to the cart, allowing unauthenticated users to disclose the contents of other customers' orders, as well as to clear and repopulate a logged in user's cart via a crafted link. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix kernel panic during driver load failure
Avoid kernel panic if MES init fails during driver load. The KIQ ring is
falsely marked as ready as ASICs that use MES, KIQ is owned by MES.
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:gfx_v12_1_wait_reg_mem+0x5a/0x1f0 [amdgpu]
Call Trace:
gfx_v12_1_ring_emit_reg_write_reg_wait+0x1f/0x30 [amdgpu]
amdgpu_gmc_fw_reg_write_reg_wait+0xb2/0x190 [amdgpu]
amdgpu_gmc_flush_gpu_tlb+0x1cc/0x230 [amdgpu]
amdgpu_gart_invalidate_tlb+0x81/0xa0 [amdgpu]
amdgpu_gart_unbind+0x72/0x90 [amdgpu]
amdgpu_ttm_backend_unbind+0xa4/0xb0 [amdgpu]
amdgpu_ttm_tt_unpopulate+0x13/0xd0 [amdgpu]
amdttm_tt_unpopulate+0x29/0x70 [amdttm]
ttm_bo_put+0x1eb/0x360 [amdttm]
amdgpu_bo_free_kernel+0xf9/0x1f0 [amdgpu]
amdgpu_ih_ring_fini+0x5a/0x90 [amdgpu]
amdgpu_irq_fini_hw+0x58/0x80 [amdgpu]
amdgpu_device_fini_hw+0x4e0/0x5b0 [amdgpu]
amdgpu_driver_load_kms+0x60/0xa0 [amdgpu]
amdgpu_pci_probe+0x28e/0x6d0 [amdgpu]
pci_device_probe+0x19f/0x220
really_probe+0x1ed/0x340
driver_probe_device+0x1e/0x80
__driver_attach+0xd3/0x1a0
bus_for_each_dev+0x68/0xa0
bus_add_driver+0x19f/0x270
driver_register+0x5d/0xf0
do_one_initcall+0xac/0x200
do_init_module+0x1ec/0x280
__se_sys_finit_module+0x2de/0x310
do_syscall_64+0x6a/0x250
entry_SYSCALL_64_after_hwframe+0x4b/0x53
(cherry picked from commit 4623b958dd6da0f4c3026afdf330626a09ecb0f0) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx10: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit ac6f00beb658239bced4aaed9efbb04a35348d48) |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: mdb: Fix source list corruption on a failed replace
When replacing the source list of an MDB remote entry, all existing
sources are first marked for deletion and vxlan_mdb_remote_srcs_add()
is then called to add the new source list. Sources present in the new
list have their deletion mark cleared, and any sources left marked
afterwards are removed.
If vxlan_mdb_remote_srcs_add() fails partway through, its error path
deletes all entries on the remote's source list. That rollback is only
correct for its other caller, vxlan_mdb_remote_add(), where the remote
was just allocated and the list contains solely entries added during
the call. On the replace path the list also holds pre-existing sources,
so a failed replace tears them down together with their (S, G)
forwarding entries instead of leaving the entry unchanged.
This is reachable from an existing (*, G) remote. An EXCLUDE filter
that loses sources starts forwarding traffic that should be blocked,
while an INCLUDE filter that loses sources drops traffic that should be
forwarded.
Mark entries created during the current pass with a new
VXLAN_SGRP_F_NEW flag. On failure, delete only those entries and clear
the deletion mark on the pre-existing ones, so a failed replace leaves
the source list untouched. Retain the flag until the whole operation
succeeds and then clear it. Also stop vxlan_mdb_remote_src_add() from
deleting a pre-existing entry it only looked up when adding that
entry's forwarding entry fails. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: fix peer refcount leak in TCP error paths
When either the TCP RX or TX error path calls ovpn_peer_hold() followed
by schedule_work(&peer->tcp.defer_del_work), and the work item is already
pending from the other path, schedule_work() returns false and the work
runs only once. Since ovpn_tcp_peer_del_work() calls ovpn_peer_put()
exactly once, the extra reference taken by the losing path is never
dropped, leaking the peer object.
The race window:
CPU0 (strparser/RX error): CPU1 (tcp_tx_work/TX error):
ovpn_peer_hold() <- refcnt+1 ovpn_peer_hold() <- refcnt+2
schedule_work() <- queued schedule_work() <- NO-OP
(work already pending)
ovpn_tcp_peer_del_work runs:
ovpn_peer_del()
ovpn_peer_put() <- refcnt+1
<- peer never freed
Fix by checking the return value of schedule_work() in both paths and
calling ovpn_peer_put() to drop the extra reference if the work was
already pending. ovpn_peer_hold() is kept unconditional in the TX path
as it cannot fail at that point. |
| In the Linux kernel, the following vulnerability has been resolved:
mctp: serial: handle zero-length frames to prevent rx buffer overflow
The MCTP serial receive state machine reads a frame length byte in
mctp_serial_push_header() case 2 and validates it upper-bound-only:
if (c > MCTP_SERIAL_FRAME_MTU) {
dev->rxstate = STATE_ERR;
} else {
dev->rxlen = c;
dev->rxpos = 0;
dev->rxstate = STATE_DATA;
...
}
A length of zero passes this check, so rxlen is set to 0 and the state
machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the
incoming byte is stored and rxpos incremented before the terminator is
dev->rxbuf[dev->rxpos] = c;
dev->rxpos++;
dev->rxstate = STATE_DATA;
if (dev->rxpos == dev->rxlen) {
dev->rxpos = 0;
dev->rxstate = STATE_TRAILER;
}
With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is
already 1 on the first data byte), so subsequent bytes are written past
the end of the fixed 74-byte rxbuf, which is the last member of the
netdev private area. Every following data byte is an attacker-controlled
1-byte out-of-bounds heap write, and the overflow continues until a
frame (0x7e) or escape byte resets the parser -- effectively unbounded.
Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line
discipline and bring the resulting mctpserialN netdev up, after which
the bytes arrive via the tty receive path.
Route a zero-length frame straight to STATE_TRAILER instead of
STATE_DATA. The trailer/framing bytes are still consumed, and the frame
resolves to a zero-length skb that the MCTP core rejects; the parser
never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can
no longer occur.
KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this
change):
UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370
index 74 is out of range for type 'u8 [74]'
BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf
Write of size 1 at addr ... by task kworker/u16:0
mctp_serial_tty_receive_buf
tty_ldisc_receive_buf
flush_to_ldisc
Allocated by task 152:
alloc_netdev_mqs
mctp_serial_open
v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so
the trailer/framing bytes are still consumed (Jeremy Kerr).
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: llsec: reject frames shorter than the authentication tag
llsec_do_decrypt_auth() computes the associated-data length for the
AEAD request as
assoclen += datalen - authlen;
where datalen is the number of bytes after the MAC header and authlen
(4, 8 or 16) is the length of the authentication tag. Nothing verifies
that the frame actually carries at least authlen payload bytes. A
secured frame whose payload is shorter than the tag makes
datalen - authlen negative; assoclen is then passed to
aead_request_set_ad() as an unsigned value close to 4 GiB, so
crypto_aead_decrypt() walks far off the end of the scatterlist that
only spans the real frame.
The frame is fully attacker-controlled and reaches this path from any
IEEE 802.15.4 peer in radio range. Reject frames whose payload is
shorter than the authentication tag before the subtraction.
Dynamically reproduced on a KASAN kernel as a general-protection-fault
in the AEAD scatterwalk, and the fix confirmed. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gpusvm: Fix MM reference leak in drm_gpusvm_range_evict
If kvmalloc_array() fails in drm_gpusvm_range_evict(), the MM
reference acquired earlier is not released, resulting in a reference
leak.
Fix this by dropping the MM reference on the kvmalloc_array()
failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/ttm: Account for NULL and handle pages in ttm_pool_backup
Pages in ttm_pool_backup can be NULL or backup handles
(ttm_backup_page_ptr_is_handle()), neither of which can be passed to
set_pages_array_wb() or freed. Add a dedicated WB pass before the
dma/purge loop that walks allocations using the same i += num_pages
stride, skipping NULL and handle entries, and calls set_pages_array_wb()
once per contiguous run of real pages. Apply the same NULL/handle guard
to the dma/purge loop.
Fixes the following oops:
Oops: general protection fault, kernel NULL pointer dereference 0x0: 0000 [#1] SMP NOPTI
RIP: 0010:__cpa_process_fault+0xf8/0x770
RSP: 0018:ffffc90000a87718 EFLAGS: 00010287
RAX: 0000000000000000 RBX: ffffc90000a87868 RCX: 0000000000000000
RDX: 0000000000001000 RSI: 0005088000000000 RDI: ffffffff827c5f34
RBP: 0005088000000000 R08: ffffc90000a877cb R09: ffffc90000a877d0
R10: 0000000000000000 R11: 000000000000001b R12: 000ffffffffff000
R13: ffffc90000a87868 R14: ffffc90000a87868 R15: ffff88815b882ae0
FS: 0000000000000000(0000) GS:ffff8884ec840000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f930b844000 CR3: 000000000262e003 CR4: 0000000008f70ef0
PKRU: 55555554
Call Trace:
<TASK>
__change_page_attr_set_clr+0x989/0xe90
? __purge_vmap_area_lazy+0x6c/0x3a0
? _vm_unmap_aliases+0x250/0x2a0
set_pages_array_wb+0x7f/0x120
ttm_pool_backup+0x4c9/0x5b0 [ttm]
? dma_resv_wait_timeout+0x3b/0xf0
ttm_tt_backup+0x32/0x60 [ttm]
ttm_bo_shrink+0x66/0x110 [ttm]
xe_bo_shrink_purge+0x12b/0x1b0 [xe]
xe_bo_shrink+0xbb/0x270 [xe]
__xe_shrinker_walk+0xf7/0x160 [xe]
xe_shrinker_walk+0x9d/0xc0 [xe]
xe_shrinker_scan+0x11f/0x210 [xe]
do_shrink_slab+0x13b/0x270
shrink_slab+0xf1/0x400
shrink_node+0x352/0x8a0
balance_pgdat+0x32c/0x700
kswapd+0x205/0x2f0
? __pfx_autoremove_wake_function+0x10/0x10
? __pfx_kswapd+0x10/0x10
kthread+0xd1/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x1b1/0x200
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix 32-bit overflow in CWSR total size calculation
total_cwsr_size was computed in 32-bit before being used as a BO/SVM
allocation size.
With large ctx_save_restore_area_size and debug_memory_size
multiplied by the XCC count, the product can wrap,
yielding an undersized CWSR save area that firmware later overruns.
Promote total_cwsr_size to u64 and use check_add_overflow()/
check_mul_overflow() in both kfd_queue_acquire_buffers() and
kfd_queue_release_buffers().
(cherry picked from commit 319f7e13423ae3f486b9aea82f9ad2d6af0ee608) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Check bounds in allocate_event_notification_slot
The valid event ids go from 0 to KFD_SIGNAL_EVENT_LIMIT
allocate_event_notification_slot has an option to specify
an event id to allocate at, used by CRIU. We weren't checking
the bounds on that value.
Check them.
v2: Lower bounds check is unecessary because of idr_alloc
already rejecting negative numbers. Upper bounds check should
be KFD_SIGNAL_EVENT_LIMIT since the signal mode mappings might
not yet exist
(cherry picked from commit 6853f1f6cbbeb3f53ebbbd7286536aeb2c5d5f50) |
| The LWS Optimize WordPress plugin before 4.1.2 does not properly escape a value submitted through an unauthenticated analytics endpoint before storing it and rendering it in an administrative dashboard, allowing unauthenticated attackers to inject arbitrary web scripts that execute when an administrator views the affected dashboard page. |
| The WP MAPS PRO WordPress plugin before 6.1.3 does not perform a capability check in one of its AJAX actions, which is also available to unauthenticated users, and does not restrict the operation it dispatches, allowing unauthenticated attackers to trigger uncontrolled recursion that exhausts server resources, resulting in a Denial of Service. |
