| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
greybus: gb-beagleplay: fix sleep in atomic context in hdlc_tx_frames()
hdlc_append() calls usleep_range() to wait for circular buffer space,
but it is called with tx_producer_lock (a spinlock) held via
hdlc_tx_frames() -> hdlc_append_tx_frame()/hdlc_append_tx_u8()/etc.
Sleeping while holding a spinlock is illegal and can trigger
"BUG: scheduling while atomic".
Fix this by moving the buffer-space wait out of hdlc_append() and into
hdlc_tx_frames(), before the spinlock is acquired. The new flow:
1. Pre-calculate the worst-case encoded frame length.
2. Wait (with sleep) outside the lock until enough space is available,
kicking the TX consumer work to drain the buffer.
3. Acquire the spinlock, re-verify space, and write the entire frame
atomically.
This ensures that sleeping only happens without any lock held, and
that frames are either fully enqueued or not written at all.
This bug is found by CodeQL static analysis tool (interprocedural
sleep-in-atomic query) and my code review. |
| In the Linux kernel, the following vulnerability has been resolved:
md/md-llbitmap: skip reading rdevs that are not in_sync
When reading bitmap pages from member disks, the code iterates through
all rdevs and attempts to read from the first available one. However,
it only checks for raid_disk assignment and Faulty flag, missing the
In_sync flag check.
This can cause bitmap data to be read from spare disks that are still
being rebuilt and don't have valid bitmap information yet. Reading
stale or uninitialized bitmap data from such disks can lead to
incorrect dirty bit tracking, potentially causing data corruption
during recovery or normal operation.
Add the In_sync flag check to ensure bitmap pages are only read from
fully synchronized member disks that have valid bitmap data. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: ns: Fix use-after-free in driver remove()
In the remove callback, if a packet arrives after destroy_workqueue() is
called, but before sock_release(), the qrtr_ns_data_ready() callback will
try to queue the work, causing use-after-free issue.
Fix this issue by saving the default 'sk_data_ready' callback during
qrtr_ns_init() and use it to replace the qrtr_ns_data_ready() callback at
the start of remove(). This ensures that even if a packet arrives after
destroy_workqueue(), the work struct will not be dereferenced.
Note that it is also required to ensure that the RX threads are completed
before destroying the workqueue, because the threads could be using the
qrtr_ns_data_ready() callback. |
| In the Linux kernel, the following vulnerability has been resolved:
net: rds: fix MR cleanup on copy error
__rds_rdma_map() hands sg/pages ownership to the transport after
get_mr() succeeds. If copying the generated cookie back to user space
fails after that point, the error path must not free those resources
again before dropping the MR reference.
Remove the duplicate unpin/free from the put_user() failure branch so
that MR teardown is handled only through the existing final cleanup
path. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: nx - fix bounce buffer leaks in nx842_crypto_{alloc,free}_ctx
The bounce buffers are allocated with __get_free_pages() using
BOUNCE_BUFFER_ORDER (order 2 = 4 pages), but both the allocation error
path and nx842_crypto_free_ctx() release the buffers with free_page().
Use free_pages() with the matching order instead. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: fix use-after-free in mwifiex_adapter_cleanup()
The mwifiex_adapter_cleanup() function uses timer_delete()
(non-synchronous) for the wakeup_timer before the adapter structure is
freed. This is incorrect because timer_delete() does not wait for any
running timer callback to complete.
If the wakeup_timer callback (wakeup_timer_fn) is executing when
mwifiex_adapter_cleanup() is called, the callback will continue to
access adapter fields (adapter->hw_status, adapter->if_ops.card_reset,
etc.) which may be freed by mwifiex_free_adapter() called later in the
mwifiex_remove_card() path.
Use timer_delete_sync() instead to ensure any running timer callback has
completed before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5: validate payload size before accessing journal metadata
r5c_recovery_analyze_meta_block() and
r5l_recovery_verify_data_checksum_for_mb() iterate over payloads in a
journal metadata block using on-disk payload size fields without
validating them against the remaining space in the metadata block.
A corrupted journal contains payload sizes extending beyond the PAGE_SIZE
boundary can cause out-of-bounds reads when accessing payload fields or
computing offsets.
Add bounds validation for each payload type to ensure the full payload
fits within meta_size before processing. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: Handle probe errors properly
The probe procedure of setup_card() in caiaq driver doesn't treat the
error cases gracefully, e.g. the error from snd_card_register() calls
snd_card_free() but continues. This would lead to a UAF for the
further calls like snd_usb_caiaq_control_init(), as Berk suggested in
another patch in the link below.
However, the problem is not only that; in general, this function drops
the all error handlings (as it's a void function) although its caller
can propagate an error to snd_probe(), which eventually calls
snd_card_free() as a proper error path. That said, we should treat
each error case in setup_card(), and just return the error code
promptly, which is then handled later as a fatal error in snd_probe().
This patch achieves it by changing the setup_card() to return an error
code. Also, the superfluous snd_card_free() call is removed, too.
Note that card->private_free can be set still safely at returning an
error. All called functions in card_free() have checks of the
unassigned resources or NULL checks. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau: fix u32 overflow in pushbuf reloc bounds check
nouveau_gem_pushbuf_reloc_apply() validates each relocation with
if (r->reloc_bo_offset + 4 > nvbo->bo.base.size)
but reloc_bo_offset is __u32 (uapi/drm/nouveau_drm.h) and the integer
literal 4 promotes to unsigned int, so the addition is performed in 32
bits and wraps before the comparison against the size_t bo size.
Cast to u64 so the addition happens in 64-bit arithmetic.
[ Add Fixes: tag. - Danilo ] |
| In the Linux kernel, the following vulnerability has been resolved:
landlock: Fix LOG_SUBDOMAINS_OFF inheritance across fork()
hook_cred_transfer() only copies the Landlock security blob when the
source credential has a domain. This is inconsistent with
landlock_restrict_self() which can set LOG_SUBDOMAINS_OFF on a
credential without creating a domain (via the ruleset_fd=-1 path): the
field is committed but not preserved across fork() because the child's
prepare_creds() calls hook_cred_transfer() which skips the copy when
domain is NULL.
This breaks the documented use case where a process mutes subdomain logs
before forking sandboxed children: the children lose the muting and
their domains produce unexpected audit records.
Fix this by unconditionally copying the Landlock credential blob. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/shstk: Prevent deadlock during shstk sigreturn
During sigreturn the shadow stack signal frame is popped. The kernel does
this by reading the shadow stack using normal read accesses. When it can't
assume the memory is shadow stack, it takes extra steps to makes sure it is
reading actual shadow stack memory and not other normal readable memory. It
does this by holding the mmap read lock while doing the access and checking
the flags of the VMA.
Unfortunately that is not safe. If the read of the shadow stack sigframe
hits a page fault, the fault handler will try to recursively grab another
mmap read lock. This normally works ok, but if a writer on another CPU is
also waiting, the second read lock could fail and cause a deadlock.
Fix this by not holding mmap lock during the read access to userspace.
Instead use mmap_lock_speculate_...() to watch for changes between dropping
mmap lock and the userspace access. Retry if anything grabbed an mmap write
lock in between and could have changed the VMA.
These mmap_lock_speculate_...() helpers use mm::mm_lock_seq, which is only
available when PER_VMA_LOCK is configured. So make X86_USER_SHADOW_STACK
depend on it. On x86, PER_VMA_LOCK is a default configuration for SMP
kernels. So drop support for the other configs under the assumption that
the !SMP shadow stack user base does not exist.
Currently there is a check that skips the lookup work when the SSP can be
assumed to be on a shadow stack. While reorganizing the function, remove
the optimization to make the tricky code flows more common, such that
issues like this cannot escape detection for so long. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmasm: fix heap over-read in ibmasm_send_i2o_message()
The ibmasm_send_i2o_message() function uses get_dot_command_size() to
compute the byte count for memcpy_toio(), but this value is derived from
user-controlled fields in the dot_command_header (command_size: u8,
data_size: u16) and is never validated against the actual allocation size.
A root user can write a small buffer with inflated header fields, causing
memcpy_toio() to read up to ~65 KB past the end of the allocation into
adjacent kernel heap, which is then forwarded to the service processor
over MMIO.
Silently clamping the copy size is not sufficient: if the header fields
claim a larger size than the buffer, the SP receives a dot command whose
own header is inconsistent with the I2O message length, which can cause
the SP to desynchronize. Reject such commands outright by returning
failure.
Validate command_size before calling get_mfa_inbound() to avoid leaking
an I2O message frame: reading INBOUND_QUEUE_PORT dequeues a hardware
frame from the controller's free pool, and returning without a
corresponding set_mfa_inbound() call would permanently exhaust it.
Additionally, clamp command_size to I2O_COMMAND_SIZE before the
memcpy_toio() so the MMIO write stays within the I2O message frame,
consistent with the clamping already performed by outgoing_message_size()
for the header field. |
| Buffer Overflow vulnerability in arendst Tasmota v.15.3.0.3 and before allows a remote attacker to execute arbitrary code via the xdrv_10_scripter.ino, fetch_jpg(), jpg_task.boundary[40], strcpy() function. |
| In the Linux kernel, the following vulnerability has been resolved:
udf: fix partition descriptor append bookkeeping
Mounting a crafted UDF image with repeated partition descriptors can
trigger a heap out-of-bounds write in part_descs_loc[].
handle_partition_descriptor() deduplicates entries by partition number,
but appended slots never record partnum. As a result duplicate
Partition Descriptors are appended repeatedly and num_part_descs keeps
growing.
Once the table is full, the growth path still sizes the allocation from
partnum even though inserts are indexed by num_part_descs. If partnum is
already aligned to PART_DESC_ALLOC_STEP, ALIGN(partnum, step) can keep
the old capacity and the next append writes past the end of the table.
Store partnum in the appended slot and size growth from the next append
count so deduplication and capacity tracking follow the same model. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: ns: Free the node during ctrl_cmd_bye()
A node sends the BYE packet when it is about to go down. So the nameserver
should advertise the removal of the node to all remote and local observers
and free the node finally. But currently, the nameserver doesn't free the
node memory even after processing the BYE packet. This causes the node
memory to leak.
Hence, remove the node from Xarray list and free the node memory during
both success and failure case of ctrl_cmd_bye(). |
| In the Linux kernel, the following vulnerability has been resolved:
media: mtk-jpeg: fix use-after-free in release path due to uncancelled work
The mtk_jpeg_release() function frees the context structure (ctx) without
first cancelling any pending or running work in ctx->jpeg_work. This
creates a race window where the workqueue callback may still be accessing
the context memory after it has been freed.
Race condition:
CPU 0 (release) CPU 1 (workqueue)
---------------- ------------------
close()
mtk_jpeg_release()
mtk_jpegenc_worker()
ctx = work->data
// accessing ctx
kfree(ctx) // freed!
access ctx // UAF!
The work is queued via queue_work() during JPEG encode/decode operations
(via mtk_jpeg_device_run). If the device is closed while work is pending
or running, the work handler will access freed memory.
Fix this by calling cancel_work_sync() BEFORE acquiring the mutex. This
ordering is critical: if cancel_work_sync() is called after mutex_lock(),
and the work handler also tries to acquire the same mutex, it would cause
a deadlock.
Note: The open error path does NOT need cancel_work_sync() because
INIT_WORK() only initializes the work structure - it does not schedule
it. Work is only scheduled later during ioctl operations. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memfd_luo: fix physical address conversion in put_folios cleanup
In memfd_luo_retrieve_folios()'s put_folios cleanup path:
1. kho_restore_folio() expects a phys_addr_t (physical address) but
receives a raw PFN (pfolio->pfn). This causes kho_restore_page() to
check the wrong physical address (pfn << PAGE_SHIFT instead of the
actual physical address).
2. This loop lacks the !pfolio->pfn check that exists in the main
retrieval loop and memfd_luo_discard_folios(), which could
incorrectly process sparse file holes where pfn=0.
Fix by converting PFN to physical address with PFN_PHYS() and adding
the !pfolio->pfn check, matching the pattern used elsewhere in this file.
This issue was identified by the AI review.
https://sashiko.dev/#/patchset/20260323110747.193569-1-duanchenghao@kylinos.cn |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: xlnx: Only access buffer information if IPI is buffered
In the receive callback check if message is NULL to prevent
possibility of crash by NULL pointer dereferencing. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix missing brelse() in ext4_xattr_inode_dec_ref_all()
The commit c8e008b60492 ("ext4: ignore xattrs past end")
introduced a refcount leak in when block_csum is false.
ext4_xattr_inode_dec_ref_all() calls ext4_get_inode_loc() to
get iloc.bh, but never releases it with brelse(). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ctxfi: Add fallback to default RSR for S/PDIF
spdif_passthru_playback_get_resources() uses atc->pll_rate as the RSR
for the MSR calculation loop. However, pll_rate is only updated in
atc_pll_init() and not in hw_pll_init(), so it remains 0 after the
card init.
When spdif_passthru_playback_setup() skips atc_pll_init() for
32000 Hz, (rsr * desc.msr) always becomes 0, causing the loop to spin
indefinitely.
Add fallback to use atc->rsr when atc->pll_rate is 0. This reflects
the hardware state, since hw_card_init() already configures the PLL
to the default RSR. |
