| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: No more self recovery
When a node withdraws and it turns out that it is the only node that has
the filesystem mounted, gfs2 currently tries to replay the local journal
to bring the filesystem back into a consistent state. Not only is that
a very bad idea, it has also never worked because gfs2_recover_func()
will refuse to do anything during a withdraw.
However, before even getting to this point, gfs2_recover_func()
dereferences sdp->sd_jdesc->jd_inode. This was a use-after-free before
commit 04133b607a78 ("gfs2: Prevent double iput for journal on error")
and is a NULL pointer dereference since then.
Simply get rid of self recovery to fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
media: ti: j721e-csi2rx: fix list_del corruption
If ti_csi2rx_start_dma() fails in ti_csi2rx_dma_callback(), the buffer is
marked done with VB2_BUF_STATE_ERROR but is not removed from the DMA queue.
This causes the same buffer to be retried in the next iteration, resulting
in a double list_del() and eventual list corruption.
Fix this by removing the buffer from the queue before calling
vb2_buffer_done() on error.
This resolves a crash due to list_del corruption:
[ 37.811243] j721e-csi2rx 30102000.ticsi2rx: Failed to queue the next buffer for DMA
[ 37.832187] slab kmalloc-2k start ffff00000255b000 pointer offset 1064 size 2048
[ 37.839761] list_del corruption. next->prev should be ffff00000255bc28, but was ffff00000255d428. (next=ffff00000255b428)
[ 37.850799] ------------[ cut here ]------------
[ 37.855424] kernel BUG at lib/list_debug.c:65!
[ 37.859876] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
[ 37.866061] Modules linked in: i2c_dev usb_f_rndis u_ether libcomposite dwc3 udc_core usb_common aes_ce_blk aes_ce_cipher ghash_ce gf128mul sha1_ce cpufreq_dt dwc3_am62 phy_gmii_sel sa2ul
[ 37.882830] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.16.0-rc3+ #28 VOLUNTARY
[ 37.890851] Hardware name: Bosch STLA-GSRV2-B0 (DT)
[ 37.895737] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 37.902703] pc : __list_del_entry_valid_or_report+0xdc/0x114
[ 37.908390] lr : __list_del_entry_valid_or_report+0xdc/0x114
[ 37.914059] sp : ffff800080003db0
[ 37.917375] x29: ffff800080003db0 x28: 0000000000000007 x27: ffff800080e50000
[ 37.924521] x26: 0000000000000000 x25: ffff0000016abb50 x24: dead000000000122
[ 37.931666] x23: ffff0000016abb78 x22: ffff0000016ab080 x21: ffff800080003de0
[ 37.938810] x20: ffff00000255bc00 x19: ffff00000255b800 x18: 000000000000000a
[ 37.945956] x17: 20747562202c3832 x16: 6362353532303030 x15: 0720072007200720
[ 37.953101] x14: 0720072007200720 x13: 0720072007200720 x12: 00000000ffffffea
[ 37.960248] x11: ffff800080003b18 x10: 00000000ffffefff x9 : ffff800080f5b568
[ 37.967396] x8 : ffff800080f5b5c0 x7 : 0000000000017fe8 x6 : c0000000ffffefff
[ 37.974542] x5 : ffff00000fea6688 x4 : 0000000000000000 x3 : 0000000000000000
[ 37.981686] x2 : 0000000000000000 x1 : ffff800080ef2b40 x0 : 000000000000006d
[ 37.988832] Call trace:
[ 37.991281] __list_del_entry_valid_or_report+0xdc/0x114 (P)
[ 37.996959] ti_csi2rx_dma_callback+0x84/0x1c4
[ 38.001419] udma_vchan_complete+0x1e0/0x344
[ 38.005705] tasklet_action_common+0x118/0x310
[ 38.010163] tasklet_action+0x30/0x3c
[ 38.013832] handle_softirqs+0x10c/0x2e0
[ 38.017761] __do_softirq+0x14/0x20
[ 38.021256] ____do_softirq+0x10/0x20
[ 38.024931] call_on_irq_stack+0x24/0x60
[ 38.028873] do_softirq_own_stack+0x1c/0x40
[ 38.033064] __irq_exit_rcu+0x130/0x15c
[ 38.036909] irq_exit_rcu+0x10/0x20
[ 38.040403] el1_interrupt+0x38/0x60
[ 38.043987] el1h_64_irq_handler+0x18/0x24
[ 38.048091] el1h_64_irq+0x6c/0x70
[ 38.051501] default_idle_call+0x34/0xe0 (P)
[ 38.055783] do_idle+0x1f8/0x250
[ 38.059021] cpu_startup_entry+0x34/0x3c
[ 38.062951] rest_init+0xb4/0xc0
[ 38.066186] console_on_rootfs+0x0/0x6c
[ 38.070031] __primary_switched+0x88/0x90
[ 38.074059] Code: b00037e0 91378000 f9400462 97e9bf49 (d4210000)
[ 38.080168] ---[ end trace 0000000000000000 ]---
[ 38.084795] Kernel panic - not syncing: Oops - BUG: Fatal exception in interrupt
[ 38.092197] SMP: stopping secondary CPUs
[ 38.096139] Kernel Offset: disabled
[ 38.099631] CPU features: 0x0000,00002000,02000801,0400420b
[ 38.105202] Memory Limit: none
[ 38.108260] ---[ end Kernel panic - not syncing: Oops - BUG: Fatal exception in interrupt ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl818x: Kill URBs before clearing tx status queue
In rtl8187_stop() move the call of usb_kill_anchored_urbs() before clearing
b_tx_status.queue. This change prevents callbacks from using already freed
skb due to anchor was not killed before freeing such skb.
BUG: kernel NULL pointer dereference, address: 0000000000000080
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Not tainted 6.15.0 #8 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.0.0 02/06/2015
RIP: 0010:ieee80211_tx_status_irqsafe+0x21/0xc0 [mac80211]
Call Trace:
<IRQ>
rtl8187_tx_cb+0x116/0x150 [rtl8187]
__usb_hcd_giveback_urb+0x9d/0x120
usb_giveback_urb_bh+0xbb/0x140
process_one_work+0x19b/0x3c0
bh_worker+0x1a7/0x210
tasklet_action+0x10/0x30
handle_softirqs+0xf0/0x340
__irq_exit_rcu+0xcd/0xf0
common_interrupt+0x85/0xa0
</IRQ>
Tested on RTL8187BvE device.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, arm64: Fix fp initialization for exception boundary
In the ARM64 BPF JIT when prog->aux->exception_boundary is set for a BPF
program, find_used_callee_regs() is not called because for a program
acting as exception boundary, all callee saved registers are saved.
find_used_callee_regs() sets `ctx->fp_used = true;` when it sees FP
being used in any of the instructions.
For programs acting as exception boundary, ctx->fp_used remains false
even if frame pointer is used by the program and therefore, FP is not
set-up for such programs in the prologue. This can cause the kernel to
crash due to a pagefault.
Fix it by setting ctx->fp_used = true for exception boundary programs as
fp is always saved in such programs. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: add NULL check in eswitch lag check
The function ice_lag_is_switchdev_running() is being called from outside of
the LAG event handler code. This results in the lag->upper_netdev being
NULL sometimes. To avoid a NULL-pointer dereference, there needs to be a
check before it is dereferenced. |
| In the Linux kernel, the following vulnerability has been resolved:
smc: Fix various oops due to inet_sock type confusion.
syzbot reported weird splats [0][1] in cipso_v4_sock_setattr() while
freeing inet_sk(sk)->inet_opt.
The address was freed multiple times even though it was read-only memory.
cipso_v4_sock_setattr() did nothing wrong, and the root cause was type
confusion.
The cited commit made it possible to create smc_sock as an INET socket.
The issue is that struct smc_sock does not have struct inet_sock as the
first member but hijacks AF_INET and AF_INET6 sk_family, which confuses
various places.
In this case, inet_sock.inet_opt was actually smc_sock.clcsk_data_ready(),
which is an address of a function in the text segment.
$ pahole -C inet_sock vmlinux
struct inet_sock {
...
struct ip_options_rcu * inet_opt; /* 784 8 */
$ pahole -C smc_sock vmlinux
struct smc_sock {
...
void (*clcsk_data_ready)(struct sock *); /* 784 8 */
The same issue for another field was reported before. [2][3]
At that time, an ugly hack was suggested [4], but it makes both INET
and SMC code error-prone and hard to change.
Also, yet another variant was fixed by a hacky commit 98d4435efcbf3
("net/smc: prevent NULL pointer dereference in txopt_get").
Instead of papering over the root cause by such hacks, we should not
allow non-INET socket to reuse the INET infra.
Let's add inet_sock as the first member of smc_sock.
[0]:
kvfree_call_rcu(): Double-freed call. rcu_head 000000006921da73
WARNING: CPU: 0 PID: 6718 at mm/slab_common.c:1956 kvfree_call_rcu+0x94/0x3f0 mm/slab_common.c:1955
Modules linked in:
CPU: 0 UID: 0 PID: 6718 Comm: syz.0.17 Tainted: G W 6.16.0-rc4-syzkaller-g7482bb149b9f #0 PREEMPT
Tainted: [W]=WARN
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : kvfree_call_rcu+0x94/0x3f0 mm/slab_common.c:1955
lr : kvfree_call_rcu+0x94/0x3f0 mm/slab_common.c:1955
sp : ffff8000a03a7730
x29: ffff8000a03a7730 x28: 00000000fffffff5 x27: 1fffe000184823d3
x26: dfff800000000000 x25: ffff0000c2411e9e x24: ffff0000dd88da00
x23: ffff8000891ac9a0 x22: 00000000ffffffea x21: ffff8000891ac9a0
x20: ffff8000891ac9a0 x19: ffff80008afc2480 x18: 00000000ffffffff
x17: 0000000000000000 x16: ffff80008ae642c8 x15: ffff700011ede14c
x14: 1ffff00011ede14c x13: 0000000000000004 x12: ffffffffffffffff
x11: ffff700011ede14c x10: 0000000000ff0100 x9 : 5fa3c1ffaf0ff000
x8 : 5fa3c1ffaf0ff000 x7 : 0000000000000001 x6 : 0000000000000001
x5 : ffff8000a03a7078 x4 : ffff80008f766c20 x3 : ffff80008054d360
x2 : 0000000000000000 x1 : 0000000000000201 x0 : 0000000000000000
Call trace:
kvfree_call_rcu+0x94/0x3f0 mm/slab_common.c:1955 (P)
cipso_v4_sock_setattr+0x2f0/0x3f4 net/ipv4/cipso_ipv4.c:1914
netlbl_sock_setattr+0x240/0x334 net/netlabel/netlabel_kapi.c:1000
smack_netlbl_add+0xa8/0x158 security/smack/smack_lsm.c:2581
smack_inode_setsecurity+0x378/0x430 security/smack/smack_lsm.c:2912
security_inode_setsecurity+0x118/0x3c0 security/security.c:2706
__vfs_setxattr_noperm+0x174/0x5c4 fs/xattr.c:251
__vfs_setxattr_locked+0x1ec/0x218 fs/xattr.c:295
vfs_setxattr+0x158/0x2ac fs/xattr.c:321
do_setxattr fs/xattr.c:636 [inline]
file_setxattr+0x1b8/0x294 fs/xattr.c:646
path_setxattrat+0x2ac/0x320 fs/xattr.c:711
__do_sys_fsetxattr fs/xattr.c:761 [inline]
__se_sys_fsetxattr fs/xattr.c:758 [inline]
__arm64_sys_fsetxattr+0xc0/0xdc fs/xattr.c:758
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x58/0x180 arch/arm64/kernel/entry-common.c:879
el0t_64_sync_handler+0x84/0x12c arch/arm64/kernel/entry-common.c:898
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600
[
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
atm: clip: Fix potential null-ptr-deref in to_atmarpd().
atmarpd is protected by RTNL since commit f3a0592b37b8 ("[ATM]: clip
causes unregister hang").
However, it is not enough because to_atmarpd() is called without RTNL,
especially clip_neigh_solicit() / neigh_ops->solicit() is unsleepable.
Also, there is no RTNL dependency around atmarpd.
Let's use a private mutex and RCU to protect access to atmarpd in
to_atmarpd(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Reject SEV{-ES} intra host migration if vCPU creation is in-flight
Reject migration of SEV{-ES} state if either the source or destination VM
is actively creating a vCPU, i.e. if kvm_vm_ioctl_create_vcpu() is in the
section between incrementing created_vcpus and online_vcpus. The bulk of
vCPU creation runs _outside_ of kvm->lock to allow creating multiple vCPUs
in parallel, and so sev_info.es_active can get toggled from false=>true in
the destination VM after (or during) svm_vcpu_create(), resulting in an
SEV{-ES} VM effectively having a non-SEV{-ES} vCPU.
The issue manifests most visibly as a crash when trying to free a vCPU's
NULL VMSA page in an SEV-ES VM, but any number of things can go wrong.
BUG: unable to handle page fault for address: ffffebde00000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
CPU: 227 UID: 0 PID: 64063 Comm: syz.5.60023 Tainted: G U O 6.15.0-smp-DEV #2 NONE
Tainted: [U]=USER, [O]=OOT_MODULE
Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.52.0-0 10/28/2024
RIP: 0010:constant_test_bit arch/x86/include/asm/bitops.h:206 [inline]
RIP: 0010:arch_test_bit arch/x86/include/asm/bitops.h:238 [inline]
RIP: 0010:_test_bit include/asm-generic/bitops/instrumented-non-atomic.h:142 [inline]
RIP: 0010:PageHead include/linux/page-flags.h:866 [inline]
RIP: 0010:___free_pages+0x3e/0x120 mm/page_alloc.c:5067
Code: <49> f7 06 40 00 00 00 75 05 45 31 ff eb 0c 66 90 4c 89 f0 4c 39 f0
RSP: 0018:ffff8984551978d0 EFLAGS: 00010246
RAX: 0000777f80000001 RBX: 0000000000000000 RCX: ffffffff918aeb98
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffffebde00000000
RBP: 0000000000000000 R08: ffffebde00000007 R09: 1ffffd7bc0000000
R10: dffffc0000000000 R11: fffff97bc0000001 R12: dffffc0000000000
R13: ffff8983e19751a8 R14: ffffebde00000000 R15: 1ffffd7bc0000000
FS: 0000000000000000(0000) GS:ffff89ee661d3000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffebde00000000 CR3: 000000793ceaa000 CR4: 0000000000350ef0
DR0: 0000000000000000 DR1: 0000000000000b5f DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
sev_free_vcpu+0x413/0x630 arch/x86/kvm/svm/sev.c:3169
svm_vcpu_free+0x13a/0x2a0 arch/x86/kvm/svm/svm.c:1515
kvm_arch_vcpu_destroy+0x6a/0x1d0 arch/x86/kvm/x86.c:12396
kvm_vcpu_destroy virt/kvm/kvm_main.c:470 [inline]
kvm_destroy_vcpus+0xd1/0x300 virt/kvm/kvm_main.c:490
kvm_arch_destroy_vm+0x636/0x820 arch/x86/kvm/x86.c:12895
kvm_put_kvm+0xb8e/0xfb0 virt/kvm/kvm_main.c:1310
kvm_vm_release+0x48/0x60 virt/kvm/kvm_main.c:1369
__fput+0x3e4/0x9e0 fs/file_table.c:465
task_work_run+0x1a9/0x220 kernel/task_work.c:227
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x7f0/0x25b0 kernel/exit.c:953
do_group_exit+0x203/0x2d0 kernel/exit.c:1102
get_signal+0x1357/0x1480 kernel/signal.c:3034
arch_do_signal_or_restart+0x40/0x690 arch/x86/kernel/signal.c:337
exit_to_user_mode_loop kernel/entry/common.c:111 [inline]
exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline]
__syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline]
syscall_exit_to_user_mode+0x67/0xb0 kernel/entry/common.c:218
do_syscall_64+0x7c/0x150 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f87a898e969
</TASK>
Modules linked in: gq(O)
gsmi: Log Shutdown Reason 0x03
CR2: ffffebde00000000
---[ end trace 0000000000000000 ]---
Deliberately don't check for a NULL VMSA when freeing the vCPU, as crashing
the host is likely desirable due to the VMSA being consumed by hardware.
E.g. if KVM manages to allow VMRUN on the vCPU, hardware may read/write a
bogus VMSA page. Accessing P
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
genirq/irq_sim: Initialize work context pointers properly
Initialize `ops` member's pointers properly by using kzalloc() instead of
kmalloc() when allocating the simulation work context. Otherwise the
pointers contain random content leading to invalid dereferencing. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: Fix NULL pointer dereference in core_scsi3_decode_spec_i_port()
The function core_scsi3_decode_spec_i_port(), in its error code path,
unconditionally calls core_scsi3_lunacl_undepend_item() passing the
dest_se_deve pointer, which may be NULL.
This can lead to a NULL pointer dereference if dest_se_deve remains
unset.
SPC-3 PR SPEC_I_PT: Unable to locate dest_tpg
Unable to handle kernel paging request at virtual address dfff800000000012
Call trace:
core_scsi3_lunacl_undepend_item+0x2c/0xf0 [target_core_mod] (P)
core_scsi3_decode_spec_i_port+0x120c/0x1c30 [target_core_mod]
core_scsi3_emulate_pro_register+0x6b8/0xcd8 [target_core_mod]
target_scsi3_emulate_pr_out+0x56c/0x840 [target_core_mod]
Fix this by adding a NULL check before calling
core_scsi3_lunacl_undepend_item() |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-qpic-snand: reallocate BAM transactions
Using the mtd_nandbiterrs module for testing the driver occasionally
results in weird things like below.
1. swiotlb mapping fails with the following message:
[ 85.926216] qcom_snand 79b0000.spi: swiotlb buffer is full (sz: 4294967294 bytes), total 512 (slots), used 0 (slots)
[ 85.932937] qcom_snand 79b0000.spi: failure in mapping desc
[ 87.999314] qcom_snand 79b0000.spi: failure to write raw page
[ 87.999352] mtd_nandbiterrs: error: write_oob failed (-110)
Rebooting the board after this causes a panic due to a NULL pointer
dereference.
2. If the swiotlb mapping does not fail, rebooting the board may result
in a different panic due to a bad spinlock magic:
[ 256.104459] BUG: spinlock bad magic on CPU#3, procd/2241
[ 256.104488] Unable to handle kernel paging request at virtual address ffffffff0000049b
...
Investigating the issue revealed that these symptoms are results of
memory corruption which is caused by out of bounds access within the
driver.
The driver uses a dynamically allocated structure for BAM transactions,
which structure must have enough space for all possible variations of
different flash operations initiated by the driver. The required space
heavily depends on the actual number of 'codewords' which is calculated
from the pagesize of the actual NAND chip.
Although the qcom_nandc_alloc() function allocates memory for the BAM
transactions during probe, but since the actual number of 'codewords'
is not yet know the allocation is done for one 'codeword' only.
Because of this, whenever the driver does a flash operation, and the
number of the required transactions exceeds the size of the allocated
arrays the driver accesses memory out of the allocated range.
To avoid this, change the code to free the initially allocated BAM
transactions memory, and allocate a new one once the actual number of
'codewords' required for a given NAND chip is known. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: uartlite: register uart driver in init
When two instances of uart devices are probing, a concurrency race can
occur. If one thread calls uart_register_driver function, which first
allocates and assigns memory to 'uart_state' member of uart_driver
structure, the other instance can bypass uart driver registration and
call ulite_assign. This calls uart_add_one_port, which expects the uart
driver to be fully initialized. This leads to a kernel panic due to a
null pointer dereference:
[ 8.143581] BUG: kernel NULL pointer dereference, address: 00000000000002b8
[ 8.156982] #PF: supervisor write access in kernel mode
[ 8.156984] #PF: error_code(0x0002) - not-present page
[ 8.156986] PGD 0 P4D 0
...
[ 8.180668] RIP: 0010:mutex_lock+0x19/0x30
[ 8.188624] Call Trace:
[ 8.188629] ? __die_body.cold+0x1a/0x1f
[ 8.195260] ? page_fault_oops+0x15c/0x290
[ 8.209183] ? __irq_resolve_mapping+0x47/0x80
[ 8.209187] ? exc_page_fault+0x64/0x140
[ 8.209190] ? asm_exc_page_fault+0x22/0x30
[ 8.209196] ? mutex_lock+0x19/0x30
[ 8.223116] uart_add_one_port+0x60/0x440
[ 8.223122] ? proc_tty_register_driver+0x43/0x50
[ 8.223126] ? tty_register_driver+0x1ca/0x1e0
[ 8.246250] ulite_probe+0x357/0x4b0 [uartlite]
To prevent it, move uart driver registration in to init function. This
will ensure that uart_driver is always registered when probe function
is called. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell_rbu: Fix list usage
Pass the correct list head to list_for_each_entry*() when looping through
the packet list.
Without this patch, reading the packet data via sysfs will show the data
incorrectly (because it starts at the wrong packet), and clearing the
packet list will result in a NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
net: clear the dst when changing skb protocol
A not-so-careful NAT46 BPF program can crash the kernel
if it indiscriminately flips ingress packets from v4 to v6:
BUG: kernel NULL pointer dereference, address: 0000000000000000
ip6_rcv_core (net/ipv6/ip6_input.c:190:20)
ipv6_rcv (net/ipv6/ip6_input.c:306:8)
process_backlog (net/core/dev.c:6186:4)
napi_poll (net/core/dev.c:6906:9)
net_rx_action (net/core/dev.c:7028:13)
do_softirq (kernel/softirq.c:462:3)
netif_rx (net/core/dev.c:5326:3)
dev_loopback_xmit (net/core/dev.c:4015:2)
ip_mc_finish_output (net/ipv4/ip_output.c:363:8)
NF_HOOK (./include/linux/netfilter.h:314:9)
ip_mc_output (net/ipv4/ip_output.c:400:5)
dst_output (./include/net/dst.h:459:9)
ip_local_out (net/ipv4/ip_output.c:130:9)
ip_send_skb (net/ipv4/ip_output.c:1496:8)
udp_send_skb (net/ipv4/udp.c:1040:8)
udp_sendmsg (net/ipv4/udp.c:1328:10)
The output interface has a 4->6 program attached at ingress.
We try to loop the multicast skb back to the sending socket.
Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr
and changes skb->protocol to v6. We enter ip6_rcv_core which
tries to use skb_dst(). But the dst is still an IPv4 one left
after IPv4 mcast output.
Clear the dst in all BPF helpers which change the protocol.
Try to preserve metadata dsts, those may carry non-routing
metadata. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix null pointer dereference in destroy_previous_session
If client set ->PreviousSessionId on kerberos session setup stage,
NULL pointer dereference error will happen. Since sess->user is not
set yet, It can pass the user argument as NULL to destroy_previous_session.
sess->user will be set in ksmbd_krb5_authenticate(). So this patch move
calling destroy_previous_session() after ksmbd_krb5_authenticate(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Avoid NULL pointer dereference in `v3d_job_update_stats()`
The following kernel Oops was recently reported by Mesa CI:
[ 800.139824] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000588
[ 800.148619] Mem abort info:
[ 800.151402] ESR = 0x0000000096000005
[ 800.155141] EC = 0x25: DABT (current EL), IL = 32 bits
[ 800.160444] SET = 0, FnV = 0
[ 800.163488] EA = 0, S1PTW = 0
[ 800.166619] FSC = 0x05: level 1 translation fault
[ 800.171487] Data abort info:
[ 800.174357] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000
[ 800.179832] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 800.184873] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 800.190176] user pgtable: 4k pages, 39-bit VAs, pgdp=00000001014c2000
[ 800.196607] [0000000000000588] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
[ 800.205305] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP
[ 800.211564] Modules linked in: vc4 snd_soc_hdmi_codec drm_display_helper v3d cec gpu_sched drm_dma_helper drm_shmem_helper drm_kms_helper drm drm_panel_orientation_quirks snd_soc_core snd_compress snd_pcm_dmaengine snd_pcm i2c_brcmstb snd_timer snd backlight
[ 800.234448] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.25+rpt-rpi-v8 #1 Debian 1:6.12.25-1+rpt1
[ 800.244182] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT)
[ 800.250005] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 800.256959] pc : v3d_job_update_stats+0x60/0x130 [v3d]
[ 800.262112] lr : v3d_job_update_stats+0x48/0x130 [v3d]
[ 800.267251] sp : ffffffc080003e60
[ 800.270555] x29: ffffffc080003e60 x28: ffffffd842784980 x27: 0224012000000000
[ 800.277687] x26: ffffffd84277f630 x25: ffffff81012fd800 x24: 0000000000000020
[ 800.284818] x23: ffffff8040238b08 x22: 0000000000000570 x21: 0000000000000158
[ 800.291948] x20: 0000000000000000 x19: ffffff8040238000 x18: 0000000000000000
[ 800.299078] x17: ffffffa8c1bd2000 x16: ffffffc080000000 x15: 0000000000000000
[ 800.306208] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
[ 800.313338] x11: 0000000000000040 x10: 0000000000001a40 x9 : ffffffd83b39757c
[ 800.320468] x8 : ffffffd842786420 x7 : 7fffffffffffffff x6 : 0000000000ef32b0
[ 800.327598] x5 : 00ffffffffffffff x4 : 0000000000000015 x3 : ffffffd842784980
[ 800.334728] x2 : 0000000000000004 x1 : 0000000000010002 x0 : 000000ba4c0ca382
[ 800.341859] Call trace:
[ 800.344294] v3d_job_update_stats+0x60/0x130 [v3d]
[ 800.349086] v3d_irq+0x124/0x2e0 [v3d]
[ 800.352835] __handle_irq_event_percpu+0x58/0x218
[ 800.357539] handle_irq_event+0x54/0xb8
[ 800.361369] handle_fasteoi_irq+0xac/0x240
[ 800.365458] handle_irq_desc+0x48/0x68
[ 800.369200] generic_handle_domain_irq+0x24/0x38
[ 800.373810] gic_handle_irq+0x48/0xd8
[ 800.377464] call_on_irq_stack+0x24/0x58
[ 800.381379] do_interrupt_handler+0x88/0x98
[ 800.385554] el1_interrupt+0x34/0x68
[ 800.389123] el1h_64_irq_handler+0x18/0x28
[ 800.393211] el1h_64_irq+0x64/0x68
[ 800.396603] default_idle_call+0x3c/0x168
[ 800.400606] do_idle+0x1fc/0x230
[ 800.403827] cpu_startup_entry+0x40/0x50
[ 800.407742] rest_init+0xe4/0xf0
[ 800.410962] start_kernel+0x5e8/0x790
[ 800.414616] __primary_switched+0x80/0x90
[ 800.418622] Code: 8b170277 8b160296 11000421 b9000861 (b9401ac1)
[ 800.424707] ---[ end trace 0000000000000000 ]---
[ 800.457313] ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---
This issue happens when the file descriptor is closed before the jobs
submitted by it are completed. When the job completes, we update the
global GPU stats and the per-fd GPU stats, which are exposed through
fdinfo. If the file descriptor was closed, then the struct `v3d_file_priv`
and its stats were already freed and we can't update the per-fd stats.
Therefore, if the file descriptor was already closed, don't u
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix null-ptr-deref when acquiring remote ip of ethernet bearer
The reproduction steps:
1. create a tun interface
2. enable l2 bearer
3. TIPC_NL_UDP_GET_REMOTEIP with media name set to tun
tipc: Started in network mode
tipc: Node identity 8af312d38a21, cluster identity 4711
tipc: Enabled bearer <eth:syz_tun>, priority 1
Oops: general protection fault
KASAN: null-ptr-deref in range
CPU: 1 UID: 1000 PID: 559 Comm: poc Not tainted 6.16.0-rc1+ #117 PREEMPT
Hardware name: QEMU Ubuntu 24.04 PC
RIP: 0010:tipc_udp_nl_dump_remoteip+0x4a4/0x8f0
the ub was in fact a struct dev.
when bid != 0 && skip_cnt != 0, bearer_list[bid] may be NULL or
other media when other thread changes it.
fix this by checking media_id. |
| In the Linux kernel, the following vulnerability has been resolved:
calipso: Fix null-ptr-deref in calipso_req_{set,del}attr().
syzkaller reported a null-ptr-deref in sock_omalloc() while allocating
a CALIPSO option. [0]
The NULL is of struct sock, which was fetched by sk_to_full_sk() in
calipso_req_setattr().
Since commit a1a5344ddbe8 ("tcp: avoid two atomic ops for syncookies"),
reqsk->rsk_listener could be NULL when SYN Cookie is returned to its
client, as hinted by the leading SYN Cookie log.
Here are 3 options to fix the bug:
1) Return 0 in calipso_req_setattr()
2) Return an error in calipso_req_setattr()
3) Alaways set rsk_listener
1) is no go as it bypasses LSM, but 2) effectively disables SYN Cookie
for CALIPSO. 3) is also no go as there have been many efforts to reduce
atomic ops and make TCP robust against DDoS. See also commit 3b24d854cb35
("tcp/dccp: do not touch listener sk_refcnt under synflood").
As of the blamed commit, SYN Cookie already did not need refcounting,
and no one has stumbled on the bug for 9 years, so no CALIPSO user will
care about SYN Cookie.
Let's return an error in calipso_req_setattr() and calipso_req_delattr()
in the SYN Cookie case.
This can be reproduced by [1] on Fedora and now connect() of nc times out.
[0]:
TCP: request_sock_TCPv6: Possible SYN flooding on port [::]:20002. Sending cookies.
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
CPU: 3 UID: 0 PID: 12262 Comm: syz.1.2611 Not tainted 6.14.0 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:read_pnet include/net/net_namespace.h:406 [inline]
RIP: 0010:sock_net include/net/sock.h:655 [inline]
RIP: 0010:sock_kmalloc+0x35/0x170 net/core/sock.c:2806
Code: 89 d5 41 54 55 89 f5 53 48 89 fb e8 25 e3 c6 fd e8 f0 91 e3 00 48 8d 7b 30 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 26 01 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b
RSP: 0018:ffff88811af89038 EFLAGS: 00010216
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffff888105266400
RDX: 0000000000000006 RSI: ffff88800c890000 RDI: 0000000000000030
RBP: 0000000000000050 R08: 0000000000000000 R09: ffff88810526640e
R10: ffffed1020a4cc81 R11: ffff88810526640f R12: 0000000000000000
R13: 0000000000000820 R14: ffff888105266400 R15: 0000000000000050
FS: 00007f0653a07640(0000) GS:ffff88811af80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f863ba096f4 CR3: 00000000163c0005 CR4: 0000000000770ef0
PKRU: 80000000
Call Trace:
<IRQ>
ipv6_renew_options+0x279/0x950 net/ipv6/exthdrs.c:1288
calipso_req_setattr+0x181/0x340 net/ipv6/calipso.c:1204
calipso_req_setattr+0x56/0x80 net/netlabel/netlabel_calipso.c:597
netlbl_req_setattr+0x18a/0x440 net/netlabel/netlabel_kapi.c:1249
selinux_netlbl_inet_conn_request+0x1fb/0x320 security/selinux/netlabel.c:342
selinux_inet_conn_request+0x1eb/0x2c0 security/selinux/hooks.c:5551
security_inet_conn_request+0x50/0xa0 security/security.c:4945
tcp_v6_route_req+0x22c/0x550 net/ipv6/tcp_ipv6.c:825
tcp_conn_request+0xec8/0x2b70 net/ipv4/tcp_input.c:7275
tcp_v6_conn_request+0x1e3/0x440 net/ipv6/tcp_ipv6.c:1328
tcp_rcv_state_process+0xafa/0x52b0 net/ipv4/tcp_input.c:6781
tcp_v6_do_rcv+0x8a6/0x1a40 net/ipv6/tcp_ipv6.c:1667
tcp_v6_rcv+0x505e/0x5b50 net/ipv6/tcp_ipv6.c:1904
ip6_protocol_deliver_rcu+0x17c/0x1da0 net/ipv6/ip6_input.c:436
ip6_input_finish+0x103/0x180 net/ipv6/ip6_input.c:480
NF_HOOK include/linux/netfilter.h:314 [inline]
NF_HOOK include/linux/netfilter.h:308 [inline]
ip6_input+0x13c/0x6b0 net/ipv6/ip6_input.c:491
dst_input include/net/dst.h:469 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:79 [inline]
ip6_rcv_finish+0xb6/0x490 net/ipv6/ip6_input.c:69
NF_HOOK include/linux/netfilter.h:314 [inline]
NF_HOOK include/linux/netf
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: wwan: t7xx: Fix napi rx poll issue
When driver handles the napi rx polling requests, the netdev might
have been released by the dellink logic triggered by the disconnect
operation on user plane. However, in the logic of processing skb in
polling, an invalid netdev is still being used, which causes a panic.
BUG: kernel NULL pointer dereference, address: 00000000000000f1
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:dev_gro_receive+0x3a/0x620
[...]
Call Trace:
<IRQ>
? __die_body+0x68/0xb0
? page_fault_oops+0x379/0x3e0
? exc_page_fault+0x4f/0xa0
? asm_exc_page_fault+0x22/0x30
? __pfx_t7xx_ccmni_recv_skb+0x10/0x10 [mtk_t7xx (HASH:1400 7)]
? dev_gro_receive+0x3a/0x620
napi_gro_receive+0xad/0x170
t7xx_ccmni_recv_skb+0x48/0x70 [mtk_t7xx (HASH:1400 7)]
t7xx_dpmaif_napi_rx_poll+0x590/0x800 [mtk_t7xx (HASH:1400 7)]
net_rx_action+0x103/0x470
irq_exit_rcu+0x13a/0x310
sysvec_apic_timer_interrupt+0x56/0x90
</IRQ> |
| In the Linux kernel, the following vulnerability has been resolved:
dma-buf: insert memory barrier before updating num_fences
smp_store_mb() inserts memory barrier after storing operation.
It is different with what the comment is originally aiming so Null
pointer dereference can be happened if memory update is reordered. |
