| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Reject firmware log with size smaller than header
fw_log_from_bo() validates the tracing buffer header_size and that the
log fits within the BO, but never checks that log->size is at least
log->header_size. fw_log_print_buffer() then computes:
u32 data_size = log->size - log->header_size;
which underflows to a near-U32_MAX value when firmware reports a log whose
size is smaller than its header. That huge data_size defeats the
log_start/log_end bounds clamps added by commit dd1311bcf0e6 ("accel/ivpu:
Add bounds checks for firmware log indices"), so fw_log_print_lines() reads
far past the small real data region of the BO. A size of 0 also makes
fw_log_from_bo() advance the offset by 0, causing the callers to loop
forever on the same header.
Reject logs whose size is smaller than the header (which also rejects
size == 0). |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: reject user command submission without a command BO
amdxdna_drm_submit_execbuf() passes the user-supplied command BO handle
straight into amdxdna_cmd_submit() with drv_cmd == NULL. When the handle
is AMDXDNA_INVALID_BO_HANDLE (0), the block that fetches job->cmd_bo is
skipped, leaving it NULL, and no check rejects it on the user path (the
!job->cmd_bo guard lives inside the != INVALID branch).
The job is then armed and pushed to the DRM scheduler.
aie2_sched_job_run() takes the drv_cmd == NULL path and calls
amdxdna_cmd_set_state(job->cmd_bo) -> amdxdna_gem_vmap(NULL) ->
to_gobj(NULL)->dev, a NULL pointer dereference in the drm_sched worker.
A process with access to the accel node on a system with a probed AMD NPU
can trigger a kernel oops with a single AMDXDNA_EXEC_CMD ioctl
(cmd_handles = 0).
Only internal driver commands (SYNC_DEBUG_BO / ATTACH_DEBUG_BO)
legitimately pass AMDXDNA_INVALID_BO_HANDLE, and they always set drv_cmd.
Reject the invalid handle for user submissions (drv_cmd == NULL) at the
submit choke point so every user path is covered.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: reject command submission on devices without a submit op
amdxdna_cmd_submit() calls xdna->dev_info->ops->cmd_submit()
unconditionally, but only aie2_dev_ops defines that callback.
aie4_vf_ops (the AIE4 SR-IOV virtual function) does not, so a user
AMDXDNA_EXEC_CMD ioctl on an AIE4 device reaches a NULL function-pointer
call and oopses the kernel. AIE4 submits work through a mapped user queue
and doorbell, not this ioctl path.
Reject the submission early with -EOPNOTSUPP when the device provides no
cmd_submit op, so the shared EXEC ioctl is a clean no-op on such devices.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
dm-verity: fix a possible NULL pointer dereference
Fix a possible NULL pointer dereference dm_verity_loadpin_is_bdev_trusted
if the device has no table. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-verity: fix buffer overflow in FEC calculation
There's a buffer overflow in dm-verity-fec:
if (neras && *neras <= v->fec->roots)
fio->erasures[(*neras)++] = i;
This allows *neras to reach roots + 1 (the post-increment pushes it past
roots). This value is then passed as no_eras to decode_rs8(). Inside the
RS decoder (lib/reed_solomon/decode_rs.c:113-121), the erasure locator
polynomial loop writes lambda[j] where j can reach nroots + 1 — one
element past the end of lambda[] (which is sized nroots + 1, valid
indices 0..nroots). The out-of-bounds write lands on syn[0], corrupting
the syndrome buffer. |
| The TrueBooker plugin for WordPress is vulnerable to Account Takeover in all versions up to, and including, 1.2.6. This is due to the add_front_user_update() AJAX handler being registered for unauthenticated users and accepting an arbitrary truebooker_wp_user_id value, which is passed directly to wp_update_user() without verifying authentication or ownership. This makes it possible for unauthenticated attackers to change any WordPress user account email address, including an administrator, by submitting the target user ID and an attacker-controlled email address. An attacker can then use the native WordPress password reset flow to receive the reset link at the attacker-controlled email address and take over the account. |
| The Real Estate Manager Pro plugin for WordPress is vulnerable to Privilege Escalation in all versions up to, and including, 12.8.6. This is due to improper capability handling in the allow_attachment_actions() function, which can treat a target user ID as a media attachment ID during user capability checks. This makes it possible for authenticated attackers, with Subscriber-level access and above, to edit an administrator account and escalate their privileges to Administrator when the targeted user ID matches the ID of an existing media attachment. |
| In the Linux kernel, the following vulnerability has been resolved:
liveupdate: validate session type before performing operation
The sessions ioctls are not applicable to all session types. PRESERVE_FD
is only applicable to outgoing sessions. RETRIEVE_FD and FINISH are only
valid for incoming session. Calling a incoming ioctl on an outgoing
session is invalid and can cause file handlers to run into unexpected
errors.
For example, a user can create a (outgoing) session, preserve a memfd,
and then immediately do a retrieve without doing a kexec in between.
This would result in memfd's retrieve handler to run. The handlers
expects to be called from a post-kexec context, and will try to do a
kho_restore_vmalloc() or kho_restore_folio() to try and restore memory.
KHO catches this (thanks to KHO_PAGE_MAGIC) and returns an error, but
since this is considered an internal error and KHO throws out a bunch of
WARN()s.
Associate a type with each ioctl op and validate the type in
luo_session_ioctl() before dispatching the ioctl handler to make sure
the op is being called for the right session type. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: use opener credentials for FSCTL mutations
SET_SPARSE, SET_ZERO_DATA and SET_COMPRESSION operate on an open SMB
handle but call VFS xattr, fallocate or fileattr helpers with the current
ksmbd worker credentials. Those helpers can revalidate inode permissions,
ownership and LSM policy independently of the SMB handle access mask.
Run each operation with the credentials captured in the target file when
the handle was opened. Keep credential handling local to these single-file
FSCTLs rather than applying session credentials to the complete IOCTL
handler, which also contains handle-less and multi-handle operations. |
| In the Linux kernel, the following vulnerability has been resolved:
device property: initialize the remaining fields of fwnode_handle in fwnode_init()
If a firmware node is allocated on the stack (for instance: temporary
software node whose life-time we control) or on the heap - but using a
non-zeroing allocation function - and initialized using fwnode_init(),
its secondary pointer will contain uninitialized memory which likely
will be neither NULL nor IS_ERR() and so may end up being dereferenced
(for example: in dev_to_swnode()). Set fwnode->secondary to NULL on
initialization. While at it: initialize the remaining fields of struct
fwnode_handle too just to be sure.
[ Fix typo in commit message. - Danilo ] |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: sdhci-esdhc-imx: disable irq during suspend to fix unhandled interrupt
When using WIFI out-of-band wakeup, an "irq xxx: nobody cared" warning
occurs. This happens because the usdhc interrupt is not disabled during
system suspend when device_may_wakeup() returns false.
The sequence of events leading to this issue:
1. System enters suspend without disabling usdhc interrupt
(because device_may_wakeup() returns false for usdhc device)
2. WIFI out-of-band wakeup triggers system resume via GPIO interrupt
3. WIFI sends a Card interrupt before usdhc has fully resumed
4. usdhc is still in runtime suspend state and cannot handle the
interrupt properly
5. The unhandled interrupt triggers "nobody cared" warning
Fix this by unconditionally disabling the usdhc interrupt during suspend
and re-enabling it during resume, regardless of the wakeup capability.
This ensures no interrupts are processed during the suspend/resume
transition. |
| In the Linux kernel, the following vulnerability has been resolved:
macsec: don't read an unset MAC header in macsec_encrypt()
macsec_encrypt() reads the Ethernet header via eth_hdr(skb)
(skb->head + skb->mac_header) to memmove() the 12 source/destination MAC
bytes forward and make room for the SecTAG.
On the AF_PACKET SOCK_RAW + PACKET_QDISC_BYPASS transmit path the skb
reaches the macsec ndo_start_xmit() with the MAC header unset, so
eth_hdr(skb) resolves to skb->head + (u16)~0 and the read is out of
bounds: a 12-byte heap over-read that is also emitted on the wire as the
frame's outer source/destination MAC. KASAN reports a slab-out-of-bounds
read in macsec_start_xmit() on 6.0; on current mainline a CONFIG_DEBUG_NET
build flags it as an unset mac header in skb_mac_header().
On the TX path the L2 header is at skb->data, so use skb_eth_hdr(), added
by commit 96cc4b69581d ("macvlan: do not assume mac_header is set in
macvlan_broadcast()") for exactly this purpose. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: use parsed transport offset in SCTP state lookup
set_sctp_state() reads the SCTP chunk header again in order to drive the
IPVS SCTP state table. For IPv6 it computes the offset with
sizeof(struct ipv6hdr), while the surrounding IPVS code uses iph.len from
ip_vs_fill_iph_skb(), where ipv6_find_hdr() has already skipped
extension headers and found the real transport header.
This makes the state machine read from the wrong offset for IPv6 SCTP
packets that carry extension headers. For example, an INIT packet with an
8-byte destination options header can be scheduled correctly by
sctp_conn_schedule(), but set_sctp_state() reads the first byte of the
SCTP verification tag as a DATA chunk type. The connection then moves
from NONE to ESTABLISHED instead of INIT1, gets the longer established
timeout, and updates the active/inactive destination counters
incorrectly. This happens even though the SCTP handshake has not
completed.
Use the parsed transport offset passed down from ip_vs_set_state() for
the SCTP chunk-header lookup. For IPv4 and IPv6 packets without
extension headers this preserves the existing offset. |
| In the Linux kernel, the following vulnerability has been resolved:
llc: fix SAP refcount leak in llc_ui_autobind()
llc_ui_autobind() opens a SAP after choosing a dynamic LSAP.
llc_sap_open() returns a reference owned by the caller, and
llc_sap_add_socket() takes a second reference for the socket's
membership in the SAP hash tables.
llc_ui_bind() drops the caller's reference after adding the socket,
but llc_ui_autobind() keeps it. When the socket is closed,
llc_sap_remove_socket() releases only the socket reference, leaving
the SAP on llc_sap_list with sk_count == 0.
This is user-visible because repeated autobind and close cycles can consume
all dynamic SAP values and make later autobinds fail with -EUSERS.
Drop the caller's reference after a successful autobind, matching
llc_ui_bind()'s ownership model. |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: remove interfaces with RCU list deletion
Queue wake, stop, and disable paths walk local->interfaces under RCU.
The bulk hardware teardown path removes entries with list_del(), so an
asynchronous transmit completion can follow a poisoned list node in
ieee802154_wake_queue().
Use list_del_rcu() as in the single-interface removal path. The following
unregister_netdevice() waits for in-flight RCU readers before freeing the
netdevice, so no separate grace-period wait is needed. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: HWS, fix matcher leak on resize target setup failure
hws_bwc_matcher_move() allocates a replacement matcher before setting it
as the resize target. If mlx5hws_matcher_resize_set_target() fails, the
replacement matcher is not attached anywhere and is leaked.
Fix the leak by destroying the replacement matcher before returning from
the resize-target failure path.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1.1.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
mlx5 HWS-capable device to test with, no runtime testing was able to be
performed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: liquidio: fix BAR resource leak on PF number failure
If cn23xx_get_pf_num() fails, the function returns without
unmapping either BAR. Unmap both BARs before returning from
the error path.
Found by manual code review. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate extension-frame layout before RX
Extension frames only have the extension header at the regular 802.11
header offset. The generic RX path can still reach helpers and interface
dispatch code that read regular header address fields before unsupported
extension subtypes are dropped.
mac80211 currently only handles S1G beacon extension frames. Drop other
extension subtypes before they can reach regular-header RX processing.
For S1G beacons, linearize the SKB with the management-frame path and
require the fixed S1G beacon header, including optional fixed fields
indicated by frame control, before generic RX dispatch.
Route S1G beacons through the station/default-link RX path without
regular-header station lookup. Avoid regular-header address reads in the
mac80211 RX paths that process S1G extension beacons, including
accept-frame, duplicate-detection, address-copy, and MLO
address-translation paths.
Also make ieee80211_get_bssid() length-safe before returning the S1G
source-address pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/spufs: fix out-of-bounds access in spufs_mem_mmap_access()
spufs_mem_mmap_access() computes the local store offset as
address - vma->vm_start, but bounds-checks it against vma->vm_end
instead of the local store size. On 64-bit, offset is always well
below vma->vm_end, so the clamp never fires and len stays unbounded
against the LS_SIZE buffer returned by ctx->ops->get_ls().
Reject offsets at or beyond LS_SIZE and clamp len to the remaining
space, mirroring the guard already used by spufs_mem_mmap_fault() and
spufs_ps_fault(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: fix more places with wrong ipv6 transport offsets
Sashiko reports for more incorrect IPv6 transport offsets.
The app code for TCP was assuming IPv4 network header
even after the ipvsh argument was provided. This can
cause problems with apps over IPv6. As for the only
official app in the kernel tree (FTP) this problem is
harmless because we use Netfilter to mangle the FTP
ports and we do not adjust the TCP seq numbers.
Also, provide correct offset of the ICMPV6 header in
ip_vs_out_icmp_v6() for correct checksum checks when
the IPv6 packet has extension headers. |
