| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ipack: ipoctal: fix stack information leak
The tty driver name is used also after registering the driver and must
specifically not be allocated on the stack to avoid leaking information
to user space (or triggering an oops).
Drivers should not try to encode topology information in the tty device
name but this one snuck in through staging without anyone noticing and
another driver has since copied this malpractice.
Fixing the ABI is a separate issue, but this at least plugs the security
hole. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: fix reconnection fail due to reserved tag allocation
We found a issue on production environment while using NVMe over RDMA,
admin_q reconnect failed forever while remote target and network is ok.
After dig into it, we found it may caused by a ABBA deadlock due to tag
allocation. In my case, the tag was hold by a keep alive request
waiting inside admin_q, as we quiesced admin_q while reset ctrl, so the
request maked as idle and will not process before reset success. As
fabric_q shares tagset with admin_q, while reconnect remote target, we
need a tag for connect command, but the only one reserved tag was held
by keep alive command which waiting inside admin_q. As a result, we
failed to reconnect admin_q forever. In order to fix this issue, I
think we should keep two reserved tags for admin queue. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: change DMA direction while mapping reinjected packets
For fragmented packets, ath12k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE. Otherwise,
an invalid payload may be reinjected into the HW and
subsequently delivered to the host.
Given that arbitrary memory can be allocated to the skb buffer,
knowledge about the data contained in the reinjected buffer is lacking.
Consequently, there’s a risk of private information being leaked.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
lib: alloc_tag_module_unload must wait for pending kfree_rcu calls
Ben Greear reports following splat:
------------[ cut here ]------------
net/netfilter/nf_nat_core.c:1114 module nf_nat func:nf_nat_register_fn has 256 allocated at module unload
WARNING: CPU: 1 PID: 10421 at lib/alloc_tag.c:168 alloc_tag_module_unload+0x22b/0x3f0
Modules linked in: nf_nat(-) btrfs ufs qnx4 hfsplus hfs minix vfat msdos fat
...
Hardware name: Default string Default string/SKYBAY, BIOS 5.12 08/04/2020
RIP: 0010:alloc_tag_module_unload+0x22b/0x3f0
codetag_unload_module+0x19b/0x2a0
? codetag_load_module+0x80/0x80
nf_nat module exit calls kfree_rcu on those addresses, but the free
operation is likely still pending by the time alloc_tag checks for leaks.
Wait for outstanding kfree_rcu operations to complete before checking
resolves this warning.
Reproducer:
unshare -n iptables-nft -t nat -A PREROUTING -p tcp
grep nf_nat /proc/allocinfo # will list 4 allocations
rmmod nft_chain_nat
rmmod nf_nat # will WARN.
[akpm@linux-foundation.org: add comment] |
| In the Linux kernel, the following vulnerability has been resolved:
debugfs: fix wait/cancellation handling during remove
Ben Greear further reports deadlocks during concurrent debugfs
remove while files are being accessed, even though the code in
question now uses debugfs cancellations. Turns out that despite
all the review on the locking, we missed completely that the
logic is wrong: if the refcount hits zero we can finish (and
need not wait for the completion), but if it doesn't we have
to trigger all the cancellations. As written, we can _never_
get into the loop triggering the cancellations. Fix this, and
explain it better while at it. |
| In the Linux kernel, the following vulnerability has been resolved:
hid: cp2112: Fix duplicate workqueue initialization
Previously the cp2112 driver called INIT_DELAYED_WORK within
cp2112_gpio_irq_startup, resulting in duplicate initilizations of the
workqueue on subsequent IRQ startups following an initial request. This
resulted in a warning in set_work_data in workqueue.c, as well as a rare
NULL dereference within process_one_work in workqueue.c.
Initialize the workqueue within _probe instead. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Define the __io_aw() hook as mmiowb()
Commit fb24ea52f78e0d595852e ("drivers: Remove explicit invocations of
mmiowb()") remove all mmiowb() in drivers, but it says:
"NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation."
The mmio in radeon_ring_commit() is protected by a mutex rather than a
spinlock, but in the mutex fastpath it behaves similar to spinlock. We
can add mmiowb() calls in the radeon driver but the maintainer says he
doesn't like such a workaround, and radeon is not the only example of
mutex protected mmio.
So we should extend the mmiowb tracking system from spinlock to mutex,
and maybe other locking primitives. This is not easy and error prone, so
we solve it in the architectural code, by simply defining the __io_aw()
hook as mmiowb(). And we no longer need to override queued_spin_unlock()
so use the generic definition.
Without this, we get such an error when run 'glxgears' on weak ordering
architectures such as LoongArch:
radeon 0000:04:00.0: ring 0 stalled for more than 10324msec
radeon 0000:04:00.0: ring 3 stalled for more than 10240msec
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000001f412 last fence id 0x000000000001f414 on ring 3)
radeon 0000:04:00.0: GPU lockup (current fence id 0x000000000000f940 last fence id 0x000000000000f941 on ring 0)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35)
radeon 0000:04:00.0: scheduling IB failed (-35).
[drm:radeon_gem_va_ioctl [radeon]] *ERROR* Couldn't update BO_VA (-35) |
| A vulnerability was identified in Docker Desktop that allows local running Linux containers to access the Docker Engine API via the configured Docker subnet, at 192.168.65.7:2375 by default. This vulnerability occurs with or without Enhanced Container Isolation (ECI) enabled, and with or without the "Expose daemon on tcp://localhost:2375 without TLS" option enabled.
This can lead to execution of a wide range of privileged commands to the engine API, including controlling other containers, creating new ones, managing images etc. In some circumstances (e.g. Docker Desktop for Windows with WSL backend) it also allows mounting the host drive with the same privileges as the user running Docker Desktop. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix racy may inline data check in dio write
syzbot reports that the following warning from ext4_iomap_begin()
triggers as of the commit referenced below:
if (WARN_ON_ONCE(ext4_has_inline_data(inode)))
return -ERANGE;
This occurs during a dio write, which is never expected to encounter
an inode with inline data. To enforce this behavior,
ext4_dio_write_iter() checks the current inline state of the inode
and clears the MAY_INLINE_DATA state flag to either fall back to
buffered writes, or enforce that any other writers in progress on
the inode are not allowed to create inline data.
The problem is that the check for existing inline data and the state
flag can span a lock cycle. For example, if the ilock is originally
locked shared and subsequently upgraded to exclusive, another writer
may have reacquired the lock and created inline data before the dio
write task acquires the lock and proceeds.
The commit referenced below loosens the lock requirements to allow
some forms of unaligned dio writes to occur under shared lock, but
AFAICT the inline data check was technically already racy for any
dio write that would have involved a lock cycle. Regardless, lift
clearing of the state bit to the same lock critical section that
checks for preexisting inline data on the inode to close the race. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: scarlett2: Add missing mutex lock around get meter levels
As scarlett2_meter_ctl_get() uses meter_level_map[], the data_mutex
should be locked while accessing it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hns3: do not allow call hns3_nic_net_open repeatedly
hns3_nic_net_open() is not allowed to called repeatly, but there
is no checking for this. When doing device reset and setup tc
concurrently, there is a small oppotunity to call hns3_nic_net_open
repeatedly, and cause kernel bug by calling napi_enable twice.
The calltrace information is like below:
[ 3078.222780] ------------[ cut here ]------------
[ 3078.230255] kernel BUG at net/core/dev.c:6991!
[ 3078.236224] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 3078.243431] Modules linked in: hns3 hclgevf hclge hnae3 vfio_iommu_type1 vfio_pci vfio_virqfd vfio pv680_mii(O)
[ 3078.258880] CPU: 0 PID: 295 Comm: kworker/u8:5 Tainted: G O 5.14.0-rc4+ #1
[ 3078.269102] Hardware name: , BIOS KpxxxFPGA 1P B600 V181 08/12/2021
[ 3078.276801] Workqueue: hclge hclge_service_task [hclge]
[ 3078.288774] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--)
[ 3078.296168] pc : napi_enable+0x80/0x84
tc qdisc sho[w 3d0e7v8 .e3t0h218 79] lr : hns3_nic_net_open+0x138/0x510 [hns3]
[ 3078.314771] sp : ffff8000108abb20
[ 3078.319099] x29: ffff8000108abb20 x28: 0000000000000000 x27: ffff0820a8490300
[ 3078.329121] x26: 0000000000000001 x25: ffff08209cfc6200 x24: 0000000000000000
[ 3078.339044] x23: ffff0820a8490300 x22: ffff08209cd76000 x21: ffff0820abfe3880
[ 3078.349018] x20: 0000000000000000 x19: ffff08209cd76900 x18: 0000000000000000
[ 3078.358620] x17: 0000000000000000 x16: ffffc816e1727a50 x15: 0000ffff8f4ff930
[ 3078.368895] x14: 0000000000000000 x13: 0000000000000000 x12: 0000259e9dbeb6b4
[ 3078.377987] x11: 0096a8f7e764eb40 x10: 634615ad28d3eab5 x9 : ffffc816ad8885b8
[ 3078.387091] x8 : ffff08209cfc6fb8 x7 : ffff0820ac0da058 x6 : ffff0820a8490344
[ 3078.396356] x5 : 0000000000000140 x4 : 0000000000000003 x3 : ffff08209cd76938
[ 3078.405365] x2 : 0000000000000000 x1 : 0000000000000010 x0 : ffff0820abfe38a0
[ 3078.414657] Call trace:
[ 3078.418517] napi_enable+0x80/0x84
[ 3078.424626] hns3_reset_notify_up_enet+0x78/0xd0 [hns3]
[ 3078.433469] hns3_reset_notify+0x64/0x80 [hns3]
[ 3078.441430] hclge_notify_client+0x68/0xb0 [hclge]
[ 3078.450511] hclge_reset_rebuild+0x524/0x884 [hclge]
[ 3078.458879] hclge_reset_service_task+0x3c4/0x680 [hclge]
[ 3078.467470] hclge_service_task+0xb0/0xb54 [hclge]
[ 3078.475675] process_one_work+0x1dc/0x48c
[ 3078.481888] worker_thread+0x15c/0x464
[ 3078.487104] kthread+0x160/0x170
[ 3078.492479] ret_from_fork+0x10/0x18
[ 3078.498785] Code: c8027c81 35ffffa2 d50323bf d65f03c0 (d4210000)
[ 3078.506889] ---[ end trace 8ebe0340a1b0fb44 ]---
Once hns3_nic_net_open() is excute success, the flag
HNS3_NIC_STATE_DOWN will be cleared. So add checking for this
flag, directly return when HNS3_NIC_STATE_DOWN is no set. |
| In the Linux kernel, the following vulnerability has been resolved:
cfg80211: fix management registrations locking
The management registrations locking was broken, the list was
locked for each wdev, but cfg80211_mgmt_registrations_update()
iterated it without holding all the correct spinlocks, causing
list corruption.
Rather than trying to fix it with fine-grained locking, just
move the lock to the wiphy/rdev (still need the list on each
wdev), we already need to hold the wdev lock to change it, so
there's no contention on the lock in any case. This trivially
fixes the bug since we hold one wdev's lock already, and now
will hold the lock that protects all lists. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ks8851: Handle softirqs at the end of IRQ thread to fix hang
The ks8851_irq() thread may call ks8851_rx_pkts() in case there are
any packets in the MAC FIFO, which calls netif_rx(). This netif_rx()
implementation is guarded by local_bh_disable() and local_bh_enable().
The local_bh_enable() may call do_softirq() to run softirqs in case
any are pending. One of the softirqs is net_rx_action, which ultimately
reaches the driver .start_xmit callback. If that happens, the system
hangs. The entire call chain is below:
ks8851_start_xmit_par from netdev_start_xmit
netdev_start_xmit from dev_hard_start_xmit
dev_hard_start_xmit from sch_direct_xmit
sch_direct_xmit from __dev_queue_xmit
__dev_queue_xmit from __neigh_update
__neigh_update from neigh_update
neigh_update from arp_process.constprop.0
arp_process.constprop.0 from __netif_receive_skb_one_core
__netif_receive_skb_one_core from process_backlog
process_backlog from __napi_poll.constprop.0
__napi_poll.constprop.0 from net_rx_action
net_rx_action from __do_softirq
__do_softirq from call_with_stack
call_with_stack from do_softirq
do_softirq from __local_bh_enable_ip
__local_bh_enable_ip from netif_rx
netif_rx from ks8851_irq
ks8851_irq from irq_thread_fn
irq_thread_fn from irq_thread
irq_thread from kthread
kthread from ret_from_fork
The hang happens because ks8851_irq() first locks a spinlock in
ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...)
and with that spinlock locked, calls netif_rx(). Once the execution
reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again
which attempts to claim the already locked spinlock again, and the
hang happens.
Move the do_softirq() call outside of the spinlock protected section
of ks8851_irq() by disabling BHs around the entire spinlock protected
section of ks8851_irq() handler. Place local_bh_enable() outside of
the spinlock protected section, so that it can trigger do_softirq()
without the ks8851_par.c ks8851_lock_par() spinlock being held, and
safely call ks8851_start_xmit_par() without attempting to lock the
already locked spinlock.
Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable()
now, replace netif_rx() with __netif_rx() which is not duplicating the
local_bh_disable()/local_bh_enable() calls. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: Convert spinlock to mutex to lock evl workqueue
drain_workqueue() cannot be called safely in a spinlocked context due to
possible task rescheduling. In the multi-task scenario, calling
queue_work() while drain_workqueue() will lead to a Call Trace as
pushing a work on a draining workqueue is not permitted in spinlocked
context.
Call Trace:
<TASK>
? __warn+0x7d/0x140
? __queue_work+0x2b2/0x440
? report_bug+0x1f8/0x200
? handle_bug+0x3c/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? __queue_work+0x2b2/0x440
queue_work_on+0x28/0x30
idxd_misc_thread+0x303/0x5a0 [idxd]
? __schedule+0x369/0xb40
? __pfx_irq_thread_fn+0x10/0x10
? irq_thread+0xbc/0x1b0
irq_thread_fn+0x21/0x70
irq_thread+0x102/0x1b0
? preempt_count_add+0x74/0xa0
? __pfx_irq_thread_dtor+0x10/0x10
? __pfx_irq_thread+0x10/0x10
kthread+0x103/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The current implementation uses a spinlock to protect event log workqueue
and will lead to the Call Trace due to potential task rescheduling.
To address the locking issue, convert the spinlock to mutex, allowing
the drain_workqueue() to be called in a safe mutex-locked context.
This change ensures proper synchronization when accessing the event log
workqueue, preventing potential Call Trace and improving the overall
robustness of the code. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: Avoid crash from unnecessary IDA free
In the remove path, there is an attempt to free the aux_idx IDA whether
it was allocated or not. This can potentially cause a crash when
unloading the driver on systems that do not initialize support for RDMA.
But, this free cannot be gated by the status bit for RDMA, since it is
allocated if the driver detects support for RDMA at probe time, but the
driver can enter into a state where RDMA is not supported after the IDA
has been allocated at probe time and this would lead to a memory leak.
Initialize aux_idx to an invalid value and check for a valid value when
unloading to determine if an IDA free is necessary. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/jfs: Add validity check for db_maxag and db_agpref
Both db_maxag and db_agpref are used as the index of the
db_agfree array, but there is currently no validity check for
db_maxag and db_agpref, which can lead to errors.
The following is related bug reported by Syzbot:
UBSAN: array-index-out-of-bounds in fs/jfs/jfs_dmap.c:639:20
index 7936 is out of range for type 'atomic_t[128]'
Add checking that the values of db_maxag and db_agpref are valid
indexes for the db_agfree array. |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: Fix freeing of uninitialized misc IRQ vector
When VSI set up failed in i40e_probe() as part of PF switch set up
driver was trying to free misc IRQ vectors in
i40e_clear_interrupt_scheme and produced a kernel Oops:
Trying to free already-free IRQ 266
WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300
Workqueue: events work_for_cpu_fn
RIP: 0010:__free_irq+0x9a/0x300
Call Trace:
? synchronize_irq+0x3a/0xa0
free_irq+0x2e/0x60
i40e_clear_interrupt_scheme+0x53/0x190 [i40e]
i40e_probe.part.108+0x134b/0x1a40 [i40e]
? kmem_cache_alloc+0x158/0x1c0
? acpi_ut_update_ref_count.part.1+0x8e/0x345
? acpi_ut_update_object_reference+0x15e/0x1e2
? strstr+0x21/0x70
? irq_get_irq_data+0xa/0x20
? mp_check_pin_attr+0x13/0xc0
? irq_get_irq_data+0xa/0x20
? mp_map_pin_to_irq+0xd3/0x2f0
? acpi_register_gsi_ioapic+0x93/0x170
? pci_conf1_read+0xa4/0x100
? pci_bus_read_config_word+0x49/0x70
? do_pci_enable_device+0xcc/0x100
local_pci_probe+0x41/0x90
work_for_cpu_fn+0x16/0x20
process_one_work+0x1a7/0x360
worker_thread+0x1cf/0x390
? create_worker+0x1a0/0x1a0
kthread+0x112/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x1f/0x40
The problem is that at that point misc IRQ vectors
were not allocated yet and we get a call trace
that driver is trying to free already free IRQ vectors.
Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED
PF state before calling i40e_free_misc_vector. This state is set only if
misc IRQ vectors were properly initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/vmalloc: combine all TLB flush operations of KASAN shadow virtual address into one operation
When compiling kernel source 'make -j $(nproc)' with the up-and-running
KASAN-enabled kernel on a 256-core machine, the following soft lockup is
shown:
watchdog: BUG: soft lockup - CPU#28 stuck for 22s! [kworker/28:1:1760]
CPU: 28 PID: 1760 Comm: kworker/28:1 Kdump: loaded Not tainted 6.10.0-rc5 #95
Workqueue: events drain_vmap_area_work
RIP: 0010:smp_call_function_many_cond+0x1d8/0xbb0
Code: 38 c8 7c 08 84 c9 0f 85 49 08 00 00 8b 45 08 a8 01 74 2e 48 89 f1 49 89 f7 48 c1 e9 03 41 83 e7 07 4c 01 e9 41 83 c7 03 f3 90 <0f> b6 01 41 38 c7 7c 08 84 c0 0f 85 d4 06 00 00 8b 45 08 a8 01 75
RSP: 0018:ffffc9000cb3fb60 EFLAGS: 00000202
RAX: 0000000000000011 RBX: ffff8883bc4469c0 RCX: ffffed10776e9949
RDX: 0000000000000002 RSI: ffff8883bb74ca48 RDI: ffffffff8434dc50
RBP: ffff8883bb74ca40 R08: ffff888103585dc0 R09: ffff8884533a1800
R10: 0000000000000004 R11: ffffffffffffffff R12: ffffed1077888d39
R13: dffffc0000000000 R14: ffffed1077888d38 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8883bc400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005577b5c8d158 CR3: 0000000004850000 CR4: 0000000000350ef0
Call Trace:
<IRQ>
? watchdog_timer_fn+0x2cd/0x390
? __pfx_watchdog_timer_fn+0x10/0x10
? __hrtimer_run_queues+0x300/0x6d0
? sched_clock_cpu+0x69/0x4e0
? __pfx___hrtimer_run_queues+0x10/0x10
? srso_return_thunk+0x5/0x5f
? ktime_get_update_offsets_now+0x7f/0x2a0
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
? hrtimer_interrupt+0x2ca/0x760
? __sysvec_apic_timer_interrupt+0x8c/0x2b0
? sysvec_apic_timer_interrupt+0x6a/0x90
</IRQ>
<TASK>
? asm_sysvec_apic_timer_interrupt+0x16/0x20
? smp_call_function_many_cond+0x1d8/0xbb0
? __pfx_do_kernel_range_flush+0x10/0x10
on_each_cpu_cond_mask+0x20/0x40
flush_tlb_kernel_range+0x19b/0x250
? srso_return_thunk+0x5/0x5f
? kasan_release_vmalloc+0xa7/0xc0
purge_vmap_node+0x357/0x820
? __pfx_purge_vmap_node+0x10/0x10
__purge_vmap_area_lazy+0x5b8/0xa10
drain_vmap_area_work+0x21/0x30
process_one_work+0x661/0x10b0
worker_thread+0x844/0x10e0
? srso_return_thunk+0x5/0x5f
? __kthread_parkme+0x82/0x140
? __pfx_worker_thread+0x10/0x10
kthread+0x2a5/0x370
? __pfx_kthread+0x10/0x10
ret_from_fork+0x30/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Debugging Analysis:
1. The following ftrace log shows that the lockup CPU spends too much
time iterating vmap_nodes and flushing TLB when purging vm_area
structures. (Some info is trimmed).
kworker: funcgraph_entry: | drain_vmap_area_work() {
kworker: funcgraph_entry: | mutex_lock() {
kworker: funcgraph_entry: 1.092 us | __cond_resched();
kworker: funcgraph_exit: 3.306 us | }
... ...
kworker: funcgraph_entry: | flush_tlb_kernel_range() {
... ...
kworker: funcgraph_exit: # 7533.649 us | }
... ...
kworker: funcgraph_entry: 2.344 us | mutex_unlock();
kworker: funcgraph_exit: $ 23871554 us | }
The drain_vmap_area_work() spends over 23 seconds.
There are 2805 flush_tlb_kernel_range() calls in the ftrace log.
* One is called in __purge_vmap_area_lazy().
* Others are called by purge_vmap_node->kasan_release_vmalloc.
purge_vmap_node() iteratively releases kasan vmalloc
allocations and flushes TLB for each vmap_area.
- [Rough calculation] Each flush_tlb_kernel_range() runs
about 7.5ms.
-- 2804 * 7.5ms = 21.03 seconds.
-- That's why a soft lock is triggered.
2. Extending the soft lockup time can work around the issue (For example,
# echo
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: protect device queue against concurrent access
In dasd_profile_start() the amount of requests on the device queue are
counted. The access to the device queue is unprotected against
concurrent access. With a lot of parallel I/O, especially with alias
devices enabled, the device queue can change while dasd_profile_start()
is accessing the queue. In the worst case this leads to a kernel panic
due to incorrect pointer accesses.
Fix this by taking the device lock before accessing the queue and
counting the requests. Additionally the check for a valid profile data
pointer can be done earlier to avoid unnecessary locking in a hot path. |
| Meshtastic is an open source mesh networking solution. In affected firmware versions crafted packets over MQTT are able to appear as a DM in client to a node even though they were not decoded with PKC. This issue has been addressed in version 2.5.19 and all users are advised to upgrade. There are no known workarounds for this vulnerability. |
