| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: ca8210: fix cas_ctl leak on spi_async failure
ca8210_spi_transfer() allocates cas_ctl with kzalloc_obj(GFP_ATOMIC)
and relies entirely on the SPI completion callback
ca8210_spi_transfer_complete() to free it.
The spi_async() API only invokes the completion callback on successful
submission. On failure it returns a negative error code without ever
queuing the callback, which leaves cas_ctl and its embedded spi_message
and spi_transfer orphaned. Every kfree(cas_ctl) in the driver is
inside the completion callback, so there is no other reclamation path.
ca8210_spi_transfer() is called from ca8210_spi_exchange(), the
interrupt handler ca8210_interrupt_handler(), and from the retry path
inside the completion callback itself. The exchange and interrupt
handler paths loop on -EBUSY, so under sustained SPI bus contention
every retry iteration leaks a fresh cas_ctl (~600 bytes per
occurrence).
Fix it by freeing cas_ctl on the spi_async() error path. While here,
correct the misleading error string: the function calls spi_async(),
not spi_sync(). |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: admin-gate legacy LLSEC dump operations
In net/ieee802154/netlink.c, the legacy IEEE802154_NL family ops table
builds the LLSEC dump entries (LLSEC_LIST_KEY, LLSEC_LIST_DEV,
LLSEC_LIST_DEVKEY, LLSEC_LIST_SECLEVEL) with IEEE802154_DUMP() which
sets no .flags, so generic netlink runs them ungated. The modern
nl802154 family admin-gates the equivalent reads via
NL802154_CMD_GET_SEC_KEY and friends with .flags = GENL_ADMIN_PERM.
Any local uid that can open AF_NETLINK / NETLINK_GENERIC can resolve
the "802.15.4 MAC" family and dump LLSEC_LIST_KEY on any wpan netdev
that has an LLSEC key installed; the dump handler writes the raw
16-byte AES-128 key bytes (IEEE802154_ATTR_LLSEC_KEY_BYTES, copied
verbatim from struct ieee802154_llsec_key.key) into the reply.
Recovering the AES key compromises 802.15.4 LLSEC link confidentiality
and authenticity, since LLSEC uses CCM* and the same key authenticates
and encrypts frames.
Impact: any local uid with no capabilities can read the raw 16-byte
AES-128 LLSEC key from the kernel keytable on any wpan netdev that has
an administrator-installed LLSEC key, by issuing an LLSEC_LIST_KEY
dump on the legacy IEEE802154_NL generic-netlink family.
Introduce IEEE802154_DUMP_PRIV() mirroring IEEE802154_DUMP() but
setting .flags = GENL_ADMIN_PERM, and use it for the four LLSEC dump
entries. LIST_PHY and LIST_IFACE retain IEEE802154_DUMP() because the
modern nl802154 family exposes their equivalents to unprivileged
readers by design (NL802154_CMD_GET_WPAN_PHY and
NL802154_CMD_GET_INTERFACE carry "can be retrieved by unprivileged
users" annotations). |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: Free BPID bitmap on setup failure
nix_setup_bpids() allocates bp->bpids with rvu_alloc_bitmap(), which uses
a plain kcalloc(). If any of the following devm_kcalloc() allocations for
the BPID mapping arrays fails, the function returns without freeing the
bitmap. Free the BPID bitmap before returning from those error paths. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ip6_tunnel: require CAP_NET_ADMIN in the device netns for changelink
ip6_tnl_changelink() operates on at most two netns, dev_net(dev) and the
tunnel link netns t->net. They differ once the device is created in or
moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in t->net can rewrite a tunnel that
lives in t->net.
Gate ip6_tnl_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ip6_gre: require CAP_NET_ADMIN in the device netns for changelink
ip6gre_changelink() and ip6erspan_changelink() operate on at most two
netns, dev_net(dev) and the tunnel link netns t->net. They differ once
the device is created in or moved to a netns other than the one the
request runs in. The rtnl changelink path checks CAP_NET_ADMIN only
against dev_net(dev), so a caller privileged there but not in t->net can
rewrite a tunnel that lives in t->net.
Gate both ops on rtnl_dev_link_net_capable() at their top, before any
attribute is parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ena: clean up XDP TX queues when regular TX setup fails
create_queues_with_size_backoff() creates XDP TX queues before setting
up the regular TX path. If the subsequent allocation or creation of
regular TX queues fails, the error handling paths omit the teardown of the
XDP TX queues, leading to a resource leak.
Fix this by explicitly destroying the XDP TX queue subset at the two
missing failure points.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have
an ENA device to test with, no runtime testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: wwan: t7xx: destroy DMA pool on CLDMA late init failure
t7xx_cldma_late_init() creates md_ctrl->gpd_dmapool before
initializing the TX and RX rings. If any ring initialization
fails, the error path frees the already initialized rings but
leaves the DMA pool allocated.
Destroy md_ctrl->gpd_dmapool on the late-init failure path
to avoid leaking the DMA pool. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: ti: icssg: guard PA stat lookups
icssg_ndo_get_stats64() unconditionally calls emac_get_stat_by_name()
with FW PA stat names regardless of whether the PA stats block is
present on the hardware. emac_get_stat_by_name() already guards the
PA stats lookup with `if (emac->prueth->pa_stats)`; when that pointer
is NULL the lookup falls through to netdev_err() and returns -EINVAL.
Because ndo_get_stats64 is polled regularly by the networking stack
this produces thousands of log entries of the form:
icssg-prueth icssg1-eth end0: Invalid stats FW_RX_ERROR
A secondary consequence is that the int(-EINVAL) return value is
implicitly widened to a near-ULLONG_MAX unsigned value when accumulated
into the __u64 fields of rtnl_link_stats64, silently corrupting the
rx_errors, rx_dropped and tx_dropped counters reported by `ip -s link`.
Every other PA-aware code path in the driver is already guarded with
the same `if (emac->prueth->pa_stats)` check. Apply the same guard
here. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sit: require CAP_NET_ADMIN in the device netns for changelink
ipip6_changelink() operates on at most two netns, dev_net(dev) and the
tunnel link netns t->net. They differ once the device is created in or
moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in t->net can rewrite a tunnel that
lives in t->net.
Gate ipip6_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed. sit was the one tunnel type not covered
by the recent series that added this check to the other changelink()
handlers. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: macsec: fix use-after-free of metadata_dst on RX SC delete
When an offloaded MACsec RX SC is deleted, macsec_del_rxsc_ctx() freed
the per-SC metadata_dst with metadata_dst_free(), which kfree()s the
object unconditionally and ignores the dst reference count. The RX
datapath in mlx5e_macsec_offload_handle_rx_skb() looks up the SC under
rcu_read_lock() via xa_load(), takes a reference with dst_hold() and
attaches the dst to the skb with skb_dst_set(). A reader that already
obtained the rx_sc pointer can race with the delete path and operate on
freed memory.
Fix the owner side by dropping the reference with dst_release() instead
of freeing unconditionally, and convert the RX datapath to
dst_hold_safe() so a reader racing the SC delete cannot attach a dst
whose last reference was just dropped; only attach it when a reference
was actually taken.
mlx5e_macsec_add_rxsc() also published sc_xarray_element via xa_alloc()
before rx_sc->md_dst was allocated and initialised, so a datapath reader
that looked the SC up by fs_id could observe rx_sc with md_dst still
NULL or, on weakly-ordered architectures, a non-NULL md_dst pointer
whose contents were not yet visible. NULL-check the xa_load() result and
md_dst on the datapath, and reorder add_rxsc() so the xa_alloc() publish
happens only after md_dst is fully initialised; the xarray RCU publish
then pairs with the rcu_read_lock()/xa_load() in the datapath.
Note: macsec_del_rxsc_ctx() also kfree()s rx_sc->sc_xarray_element
without an RCU grace period while the same datapath reads it under
rcu_read_lock(); that is a separate pre-existing issue left to a
follow-up patch.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix race condition in reset_device sysfs callback
The ims_pcu_reset_device() sysfs callback calls ims_pcu_execute_command()
without acquiring pcu->cmd_mutex. This can lead to data races and
corruption of the shared command buffer if triggered concurrently with
other commands.
Acquire pcu->cmd_mutex before calling ims_pcu_execute_command(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: xen: scsiback: Free the command tag on the TMR submit-failure path
scsiback_device_action() obtains a command tag in
scsiback_get_pend_req() and submits a task-management request with
target_submit_tmr(). When target_submit_tmr() fails it returns < 0 and
scsiback jumps to the err: label, which sends a response but frees
nothing, leaking the tag.
Impact: a pvSCSI guest can leak the command tags of a LUN's session,
stopping the LUN, by issuing VSCSIIF_ACT_SCSI_ABORT or RESET requests
whenever target_submit_tmr() fails.
transport_generic_free_cmd() cannot be used here. By the time
target_submit_tmr() returns an error it has already run
__target_init_cmd() (so se_cmd->cmd_kref is one, not zero), and on its
target_get_sess_cmd() error path it has freed se_cmd->se_tmr_req via
core_tmr_release_req() while leaving SCF_SCSI_TMR_CDB set and the
pointer dangling. Letting the command release run target_free_cmd_mem()
would then double-free se_tmr_req.
Use the same helper, which returns just the tag, on this path too. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix memory leak in lpfc_sli4_driver_resource_setup()
The memory allocated for mboxq using mempool_alloc() is not freed in
some of the early exit error paths. Fix that by moving the
mempool_free() call to an earlier point after last use. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-ioctl: fix a possible overflow in list_version_get_info
sizeof(tt->version) is 12 bytes, but the code writes 16 bytes into the
output buffer - info->vers->version[0], info->vers->version[1],
info->vers->version[2] and info->vers->next. This can cause buffer
overflow.
Fix this buffer overflow by replacing "sizeof(tt->version)" with
"sizeof(struct dm_target_versions)". |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: use unconditional synchronize_rcu() in isotp_release()
isotp_notify() unregisters the (RCU) CAN filters via can_rx_unregister()
and clears so->bound without waiting for a grace period. isotp_release()
uses so->bound to decide whether it needs to call synchronize_rcu()
before cancelling so->rxtimer, so when NETDEV_UNREGISTER runs first it
skips that synchronize_rcu() and can cancel the timer while an
in-flight isotp_rcv() is still executing and about to re-arm it via
isotp_send_fc(), leading to a use-after-free timer callback on the
freed socket.
sakisho-bot remarked a problem with rtnl_lock held in isotp_notify(),
therefore make isotp_release() always call synchronize_rcu() before
cancelling the timers, regardless of so->bound. This still closes the
original race (isotp_notify() clearing so->bound without waiting for
in-flight isotp_rcv() callers before isotp_release() cancels the RX
timer) without adding any RCU wait to the netdevice notifier path. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: mt7621: avoid corruption of shared interrupt trigger state
The bank-shared fields like 'rising' and 'falling' are modified using
non-atomic read-modify-write operations. Since every gpio chip instance
represents an entire bank of 32 pins, if 'mediatek_gpio_irq_type()' is
called concurrently for different IRQs on the same bank a possible overwrite
of each other's configuration is possible. Thus, protect this state with
'gpio_generic_lock_irqsave' lock in the same way it is handled in irp_chip
'mediatek_gpio_irq_mask()' and 'mediatek_gpio_irq_unmask()' callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: Sync page pool RX frags for CPU
MANA allocates RX buffers from page pool fragments when frag_count is
greater than 1. In that case the buffers remain DMA mapped by page pool
and the RX completion path does not call dma_unmap_single(). As a result,
the implicit sync-for-CPU normally performed by dma_unmap_single() is
missing before the packet data is passed to the networking stack.
This breaks RX on configurations which require explicit DMA syncing, for
example when booted with swiotlb=force.
Fix this by recording the page pool page and DMA sync offset when the RX
buffer is allocated, and syncing the received packet range for CPU access
before handing the RX buffer to the stack. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: Validate the packet length reported by the NIC
Validate the packet length reported in the RX CQE before passing it
to skb processing. The CQE is supplied by the NIC device and should
not be blindly trusted. |
| In the Linux kernel, the following vulnerability has been resolved:
cpu: hotplug: Bound hotplug states sysfs output
states_show() adds CPU hotplug state names into a single sysfs buffer
using sprintf(). With enough registered states, this can write past the
end of the PAGE_SIZE buffer.
Use sysfs_emit_at() so output is bounded. |
| In the Linux kernel, the following vulnerability has been resolved:
cpu: hotplug: Preserve per instance callback errors
cpuhp_invoke_callback() unwinds earlier callbacks for the same
hotplug state when one instance fails. The rollback path currently
reuses ret, so a successful rollback can hide the original error and
make the failed transition look successful.
Keep the rollback result separate from the original error. |
