| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix stackmap overflow check in __bpf_get_stackid()
Syzkaller reported a KASAN slab-out-of-bounds write in __bpf_get_stackid()
when copying stack trace data. The issue occurs when the perf trace
contains more stack entries than the stack map bucket can hold,
leading to an out-of-bounds write in the bucket's data array. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: fix uninit memory after failed mi_read in mi_format_new
Fix a KMSAN un-init bug found by syzkaller.
ntfs_get_bh() expects a buffer from sb_getblk(), that buffer may not be
uptodate. We do not bring the buffer uptodate before setting it as
uptodate. If the buffer were to not be uptodate, it could mean adding a
buffer with un-init data to the mi record. Attempting to load that record
will trigger KMSAN.
Avoid this by setting the buffer as uptodate, if it’s not already, by
overwriting it. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix incorrect splitting in btrfs_drop_extent_map_range
In production we were seeing a variety of WARN_ON()'s in the extent_map
code, specifically in btrfs_drop_extent_map_range() when we have to call
add_extent_mapping() for our second split.
Consider the following extent map layout
PINNED
[0 16K) [32K, 48K)
and then we call btrfs_drop_extent_map_range for [0, 36K), with
skip_pinned == true. The initial loop will have
start = 0
end = 36K
len = 36K
we will find the [0, 16k) extent, but since we are pinned we will skip
it, which has this code
start = em_end;
if (end != (u64)-1)
len = start + len - em_end;
em_end here is 16K, so now the values are
start = 16K
len = 16K + 36K - 16K = 36K
len should instead be 20K. This is a problem when we find the next
extent at [32K, 48K), we need to split this extent to leave [36K, 48k),
however the code for the split looks like this
split->start = start + len;
split->len = em_end - (start + len);
In this case we have
em_end = 48K
split->start = 16K + 36K // this should be 16K + 20K
split->len = 48K - (16K + 36K) // this overflows as 16K + 36K is 52K
and now we have an invalid extent_map in the tree that potentially
overlaps other entries in the extent map. Even in the non-overlapping
case we will have split->start set improperly, which will cause problems
with any block related calculations.
We don't actually need len in this loop, we can simply use end as our
end point, and only adjust start up when we find a pinned extent we need
to skip.
Adjust the logic to do this, which keeps us from inserting an invalid
extent map.
We only skip_pinned in the relocation case, so this is relatively rare,
except in the case where you are running relocation a lot, which can
happen with auto relocation on. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: Fix uninit buffer allocated by __getname()
Fix uninit errors caused after buffer allocation given to 'de'; by
initializing the buffer with zeroes. The fix was found by using KMSAN. |
| In the Linux kernel, the following vulnerability has been resolved:
smack: fix bug: unprivileged task can create labels
If an unprivileged task is allowed to relabel itself
(/smack/relabel-self is not empty),
it can freely create new labels by writing their
names into own /proc/PID/attr/smack/current
This occurs because do_setattr() imports
the provided label in advance,
before checking "relabel-self" list.
This change ensures that the "relabel-self" list
is checked before importing the label. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: qcom-adm: fix wrong calling convention for prep_slave_sg
The calling convention for pre_slave_sg is to return NULL on error and
provide an error log to the system. Qcom-adm instead provide error
pointer when an error occur. This indirectly cause kernel panic for
example for the nandc driver that checks only if the pointer returned by
device_prep_slave_sg is not NULL. Returning an error pointer makes nandc
think the device_prep_slave_sg function correctly completed and makes
the kernel panics later in the code.
While nandc is the one that makes the kernel crash, it was pointed out
that the real problem is qcom-adm not following calling convention for
that function.
To fix this, drop returning error pointer and return NULL with an error
log. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix possible use-after-free in async command interface
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x7d
print_report.cold+0x2d5/0x684
? do_raw_spin_lock+0x23d/0x270
kasan_report+0xb1/0x1a0
? do_raw_spin_lock+0x23d/0x270
do_raw_spin_lock+0x23d/0x270
? rwlock_bug.part.0+0x90/0x90
? __delete_object+0xb8/0x100
? lock_downgrade+0x6e0/0x6e0
_raw_spin_lock_irqsave+0x43/0x60
? __wake_up_common_lock+0xb9/0x140
__wake_up_common_lock+0xb9/0x140
? __wake_up_common+0x650/0x650
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kasan_set_track+0x21/0x30
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kfree+0x1ba/0x520
? do_raw_spin_unlock+0x54/0x220
mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core]
? dump_command+0xcc0/0xcc0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
? irq_release+0x140/0x140 [mlx5_core]
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x1f2/0x620
handle_irq_event+0xb2/0x1d0
handle_edge_irq+0x21e/0xb00
__common_interrupt+0x79/0x1a0
common_interrupt+0x78/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x42/0x60
Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 <c3> 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00
RSP: 0018:ffff888100dbfdf0 EFLAGS: 00000242
RAX: 0000000000000001 RBX: ffffffff84ecbd48 RCX: 1ffffffff0afe110
RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffff835cc9bc
RBP: 0000000000000005 R08: 0000000000000001 R09: ffff88881dec4ac3
R10: ffffed1103bd8958 R11: 0000017d0ca571c9 R12: 0000000000000005
R13: ffffffff84f024e0 R14: 0000000000000000 R15: dffffc0000000000
? default_idle_call+0xcc/0x450
default_idle_call+0xec/0x450
do_idle+0x394/0x450
? arch_cpu_idle_exit+0x40/0x40
? do_idle+0x17/0x450
cpu_startup_entry+0x19/0x20
start_secondary+0x221/0x2b0
? set_cpu_sibling_map+0x2070/0x2070
secondary_startup_64_no_verify+0xcd/0xdb
</TASK>
Allocated by task 49502:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
kvmalloc_node+0x48/0xe0
mlx5e_bulk_async_init+0x35/0x110 [mlx5_core]
mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1c
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
s390/lcs: Fix return type of lcs_start_xmit()
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: idmouse: fix an uninit-value in idmouse_open
In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.
Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.
Note that this is found by KMSAN, so only kernel compilation
is tested. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: hif_usb: fix memory leak of urbs in ath9k_hif_usb_dealloc_tx_urbs()
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix hard lockup when reading the rx_monitor from debugfs
During I/O and simultaneous cat of /sys/kernel/debug/lpfc/fnX/rx_monitor, a
hard lockup similar to the call trace below may occur.
The spin_lock_bh in lpfc_rx_monitor_report is not protecting from timer
interrupts as expected, so change the strength of the spin lock to _irq.
Kernel panic - not syncing: Hard LOCKUP
CPU: 3 PID: 110402 Comm: cat Kdump: loaded
exception RIP: native_queued_spin_lock_slowpath+91
[IRQ stack]
native_queued_spin_lock_slowpath at ffffffffb814e30b
_raw_spin_lock at ffffffffb89a667a
lpfc_rx_monitor_record at ffffffffc0a73a36 [lpfc]
lpfc_cmf_timer at ffffffffc0abbc67 [lpfc]
__hrtimer_run_queues at ffffffffb8184250
hrtimer_interrupt at ffffffffb8184ab0
smp_apic_timer_interrupt at ffffffffb8a026ba
apic_timer_interrupt at ffffffffb8a01c4f
[End of IRQ stack]
apic_timer_interrupt at ffffffffb8a01c4f
lpfc_rx_monitor_report at ffffffffc0a73c80 [lpfc]
lpfc_rx_monitor_read at ffffffffc0addde1 [lpfc]
full_proxy_read at ffffffffb83e7fc3
vfs_read at ffffffffb833fe71
ksys_read at ffffffffb83402af
do_syscall_64 at ffffffffb800430b
entry_SYSCALL_64_after_hwframe at ffffffffb8a000ad |
| In the Linux kernel, the following vulnerability has been resolved:
staging: media: tegra-video: fix device_node use after free
At probe time this code path is followed:
* tegra_csi_init
* tegra_csi_channels_alloc
* for_each_child_of_node(node, channel) -- iterates over channels
* automatically gets 'channel'
* tegra_csi_channel_alloc()
* saves into chan->of_node a pointer to the channel OF node
* automatically gets and puts 'channel'
* now the node saved in chan->of_node has refcount 0, can disappear
* tegra_csi_channels_init
* iterates over channels
* tegra_csi_channel_init -- uses chan->of_node
After that, chan->of_node keeps storing the node until the device is
removed.
of_node_get() the node and of_node_put() it during teardown to avoid any
risk. |
| In the Linux kernel, the following vulnerability has been resolved:
acct: fix potential integer overflow in encode_comp_t()
The integer overflow is descripted with following codes:
> 317 static comp_t encode_comp_t(u64 value)
> 318 {
> 319 int exp, rnd;
......
> 341 exp <<= MANTSIZE;
> 342 exp += value;
> 343 return exp;
> 344 }
Currently comp_t is defined as type of '__u16', but the variable 'exp' is
type of 'int', so overflow would happen when variable 'exp' in line 343 is
greater than 65535. |
| In the Linux kernel, the following vulnerability has been resolved:
configfs: fix possible memory leak in configfs_create_dir()
kmemleak reported memory leaks in configfs_create_dir():
unreferenced object 0xffff888009f6af00 (size 192):
comm "modprobe", pid 3777, jiffies 4295537735 (age 233.784s)
backtrace:
kmem_cache_alloc (mm/slub.c:3250 mm/slub.c:3256 mm/slub.c:3263 mm/slub.c:3273)
new_fragment (./include/linux/slab.h:600 fs/configfs/dir.c:163)
configfs_register_subsystem (fs/configfs/dir.c:1857)
basic_write (drivers/hwtracing/stm/p_basic.c:14) stm_p_basic
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
unreferenced object 0xffff888003ba7180 (size 96):
comm "modprobe", pid 3777, jiffies 4295537735 (age 233.784s)
backtrace:
kmem_cache_alloc (mm/slub.c:3250 mm/slub.c:3256 mm/slub.c:3263 mm/slub.c:3273)
configfs_new_dirent (./include/linux/slab.h:723 fs/configfs/dir.c:194)
configfs_make_dirent (fs/configfs/dir.c:248)
configfs_create_dir (fs/configfs/dir.c:296)
configfs_attach_group.isra.28 (fs/configfs/dir.c:816 fs/configfs/dir.c:852)
configfs_register_subsystem (fs/configfs/dir.c:1881)
basic_write (drivers/hwtracing/stm/p_basic.c:14) stm_p_basic
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
This is because the refcount is not correct in configfs_make_dirent().
For normal stage, the refcount is changing as:
configfs_register_subsystem()
configfs_create_dir()
configfs_make_dirent()
configfs_new_dirent() # set s_count = 1
dentry->d_fsdata = configfs_get(sd); # s_count = 2
...
configfs_unregister_subsystem()
configfs_remove_dir()
remove_dir()
configfs_remove_dirent() # s_count = 1
dput() ...
*dentry_unlink_inode()*
configfs_d_iput() # s_count = 0, release
However, if we failed in configfs_create():
configfs_register_subsystem()
configfs_create_dir()
configfs_make_dirent() # s_count = 2
...
configfs_create() # fail
->out_remove:
configfs_remove_dirent(dentry)
configfs_put(sd) # s_count = 1
return PTR_ERR(inode);
There is no inode in the error path, so the configfs_d_iput() is lost
and makes sd and fragment memory leaked.
To fix this, when we failed in configfs_create(), manually call
configfs_put(sd) to keep the refcount correct. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix PCI device refcount leak in amdgpu_atrm_get_bios()
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in amdgpu_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: marvell/octeontx - prevent integer overflows
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "code_length * 2" can overflow. The round_up(ucode_size, 16) +
sizeof() expression can overflow too. Prevent these overflows. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6/sit: use DEV_STATS_INC() to avoid data-races
syzbot/KCSAN reported that multiple cpus are updating dev->stats.tx_error
concurrently.
This is because sit tunnels are NETIF_F_LLTX, meaning their ndo_start_xmit()
is not protected by a spinlock.
While original KCSAN report was about tx path, rx path has the same issue. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: mxcmmc: fix return value check of mmc_add_host()
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix refcount leak in hns_roce_mmap
rdma_user_mmap_entry_get_pgoff() takes the reference.
Add missing rdma_user_mmap_entry_put() to release the reference.
Acked-by Haoyue Xu <xuhaoyue1@hisilicon.com> |
| In the Linux kernel, the following vulnerability has been resolved:
fortify: Fix __compiletime_strlen() under UBSAN_BOUNDS_LOCAL
With CONFIG_FORTIFY=y and CONFIG_UBSAN_LOCAL_BOUNDS=y enabled, we observe
a runtime panic while running Android's Compatibility Test Suite's (CTS)
android.hardware.input.cts.tests. This is stemming from a strlen()
call in hidinput_allocate().
__compiletime_strlen() is implemented in terms of __builtin_object_size(),
then does an array access to check for NUL-termination. A quirk of
__builtin_object_size() is that for strings whose values are runtime
dependent, __builtin_object_size(str, 1 or 0) returns the maximum size
of possible values when those sizes are determinable at compile time.
Example:
static const char *v = "FOO BAR";
static const char *y = "FOO BA";
unsigned long x (int z) {
// Returns 8, which is:
// max(__builtin_object_size(v, 1), __builtin_object_size(y, 1))
return __builtin_object_size(z ? v : y, 1);
}
So when FORTIFY_SOURCE is enabled, the current implementation of
__compiletime_strlen() will try to access beyond the end of y at runtime
using the size of v. Mixed with UBSAN_LOCAL_BOUNDS we get a fault.
hidinput_allocate() has a local C string whose value is control flow
dependent on a switch statement, so __builtin_object_size(str, 1)
evaluates to the maximum string length, making all other cases fault on
the last character check. hidinput_allocate() could be cleaned up to
avoid runtime calls to strlen() since the local variable can only have
literal values, so there's no benefit to trying to fortify the strlen
call site there.
Perform a __builtin_constant_p() check against index 0 earlier in the
macro to filter out the control-flow-dependant case. Add a KUnit test
for checking the expected behavioral characteristics of FORTIFY_SOURCE
internals. |
