| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: validate ND option lengths in vxlan_na_create
vxlan_na_create() walks ND options according to option-provided
lengths. A malformed option can make the parser advance beyond the
computed option span or use a too-short source LLADDR option payload.
Validate option lengths against the remaining NS option area before
advancing, and only read source LLADDR when the option is large enough
for an Ethernet address. |
| In the Linux kernel, the following vulnerability has been resolved:
counter: rz-mtu3-cnt: do not use struct rz_mtu3_channel's dev member
The counter driver can use HW channels 1 and 2, while the PWM driver can
use HW channels 0, 1, 2, 3, 4, 6, 7.
The dev member is assigned both by the counter driver and the PWM driver
for channels 1 and 2, to their own struct device instance, overwriting
the previous value.
The sub-drivers race to assign their own struct device pointer to the
same struct rz_mtu3_channel's dev member.
The dev member of struct rz_mtu3_channel is used by the counter
sub-driver for runtime PM.
Depending on the probe order of the counter and PWM sub-drivers, the
dev member may point to the wrong struct device instance, causing the
counter sub-driver to do runtime PM actions on the wrong device.
To fix this, use the parent pointer of the counter, which is assigned
during probe to the correct struct device, not the struct device pointer
inside the shared struct rz_mtu3_channel. |
| In the Linux kernel, the following vulnerability has been resolved:
reset: gpio: fix double free in reset_add_gpio_aux_device() error path
When __auxiliary_device_add() fails, reset_add_gpio_aux_device()
calls auxiliary_device_uninit(adev).
The device release callback reset_gpio_aux_device_release() frees
adev, but the current error path then calls kfree(adev) again,
causing a double free.
Keep kfree(adev) for the auxiliary_device_init() failure path, but
avoid freeing adev after auxiliary_device_uninit(). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Fix memory leak with CCA cards used as accelerator
Tests showed that there is a memory leak if CCA cards are used as
accelerator for clear key RSA requests (ME and CRT). With the last
rework for the memory allocation the AP messages are allocated by
ap_init_apmsg() but for some reason on two places (ME and CRT) the
older allocation was still in place. So the first allocation simple
was never freed. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: ni_atmio16d: Fix invalid clean-up after failed attach
If the driver's COMEDI "attach" handler function (`atmio16d_attach()`)
returns an error, the COMEDI core will call the driver's "detach"
handler function (`atmio16d_detach()`) to clean up. This calls
`reset_atmio16d()` unconditionally, but depending on where the error
occurred in the attach handler, the device may not have been
sufficiently initialized to call `reset_atmio16d()`. It uses
`dev->iobase` as the I/O port base address and `dev->private` as the
pointer to the COMEDI device's private data structure. `dev->iobase`
may still be set to its initial value of 0, which would result in
undesired writes to low I/O port addresses. `dev->private` may still be
`NULL`, which would result in null pointer dereferences.
Fix `atmio16d_detach()` by checking that `dev->private` is valid
(non-null) before calling `reset_atmio16d()`. This implies that
`dev->iobase` was set correctly since that is set up before
`dev->private`. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: dt2815: add hardware detection to prevent crash
The dt2815 driver crashes when attached to I/O ports without actual
hardware present. This occurs because syzkaller or users can attach
the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl.
When no hardware exists at the specified port, inb() operations return
0xff (floating bus), but outb() operations can trigger page faults due
to undefined behavior, especially under race conditions:
BUG: unable to handle page fault for address: 000000007fffff90
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:dt2815_attach+0x6e0/0x1110
Add hardware detection by reading the status register before attempting
any write operations. If the read returns 0xff, assume no hardware is
present and fail the attach with -ENODEV. This prevents crashes from
outb() operations on non-existent hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050: Fix irq resource leak
The interrupt handler is setup but only a few lines down if
iio_trigger_register() fails the function returns without properly
releasing the handler.
Add cleanup goto to resolve resource leak.
Detected by Smatch:
drivers/iio/gyro/mpu3050-core.c:1128 mpu3050_trigger_probe() warn:
'irq' from request_threaded_irq() not released on lines: 1124. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate doorbell_offset in user queue creation
amdgpu_userq_get_doorbell_index() passes the user-provided
doorbell_offset to amdgpu_doorbell_index_on_bar() without bounds
checking. An arbitrarily large doorbell_offset can cause the
calculated doorbell index to fall outside the allocated doorbell BO,
potentially corrupting kernel doorbell space.
Validate that doorbell_offset falls within the doorbell BO before
computing the BAR index, using u64 arithmetic to prevent overflow.
(cherry picked from commit de1ef4ffd70e1d15f0bf584fd22b1f28cbd5e2ec) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: fix u8 overflow in SSID scan buffer size calculation
The variable valuesize is declared as u8 but accumulates the total
length of all SSIDs to scan. Each SSID contributes up to 33 bytes
(IEEE80211_MAX_SSID_LEN + 1), and with WILC_MAX_NUM_PROBED_SSID (10)
SSIDs the total can reach 330, which wraps around to 74 when stored
in a u8.
This causes kmalloc to allocate only 75 bytes while the subsequent
memcpy writes up to 331 bytes into the buffer, resulting in a 256-byte
heap buffer overflow.
Widen valuesize from u8 to u32 to accommodate the full range. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/qaic: Handle DBC deactivation if the owner went away
When a DBC is released, the device sends a QAIC_TRANS_DEACTIVATE_FROM_DEV
transaction to the host over the QAIC_CONTROL MHI channel. QAIC handles
this by calling decode_deactivate() to release the resources allocated for
that DBC. Since that handling is done in the qaic_manage_ioctl() context,
if the user goes away before receiving and handling the deactivation, the
host will be out-of-sync with the DBCs available for use, and the DBC
resources will not be freed unless the device is removed. If another user
loads and requests to activate a network, then the device assigns the same
DBC to that network, QAIC will "indefinitely" wait for dbc->in_use = false,
leading the user process to hang.
As a solution to this, handle QAIC_TRANS_DEACTIVATE_FROM_DEV transactions
that are received after the user has gone away. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix incorrect pruning due to atomic fetch precision tracking
When backtrack_insn encounters a BPF_STX instruction with BPF_ATOMIC
and BPF_FETCH, the src register (or r0 for BPF_CMPXCHG) also acts as
a destination, thus receiving the old value from the memory location.
The current backtracking logic does not account for this. It treats
atomic fetch operations the same as regular stores where the src
register is only an input. This leads the backtrack_insn to fail to
propagate precision to the stack location, which is then not marked
as precise!
Later, the verifier's path pruning can incorrectly consider two states
equivalent when they differ in terms of stack state. Meaning, two
branches can be treated as equivalent and thus get pruned when they
should not be seen as such.
Fix it as follows: Extend the BPF_LDX handling in backtrack_insn to
also cover atomic fetch operations via is_atomic_fetch_insn() helper.
When the fetch dst register is being tracked for precision, clear it,
and propagate precision over to the stack slot. For non-stack memory,
the precision walk stops at the atomic instruction, same as regular
BPF_LDX. This covers all fetch variants.
Before:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs=r2 stack= before 2: (b7) r2 = 0
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit
After:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs= stack=-8 before 2: (b7) r2 = 0
mark_precise: frame0: regs= stack=-8 before 1: (7b) *(u64 *)(r10 -8) = r1
mark_precise: frame0: regs=r1 stack= before 0: (b7) r1 = 8
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject sleepable kprobe_multi programs at attach time
kprobe.multi programs run in atomic/RCU context and cannot sleep.
However, bpf_kprobe_multi_link_attach() did not validate whether the
program being attached had the sleepable flag set, allowing sleepable
helpers such as bpf_copy_from_user() to be invoked from a non-sleepable
context.
This causes a "sleeping function called from invalid context" splat:
BUG: sleeping function called from invalid context at ./include/linux/uaccess.h:169
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1787, name: sudo
preempt_count: 1, expected: 0
RCU nest depth: 2, expected: 0
Fix this by rejecting sleepable programs early in
bpf_kprobe_multi_link_attach(), before any further processing. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_event: fix potential UAF in hci_le_remote_conn_param_req_evt
hci_conn lookup and field access must be covered by hdev lock in
hci_le_remote_conn_param_req_evt, otherwise it's possible it is freed
concurrently.
Extend the hci_dev_lock critical section to cover all conn usage. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: validate LTK enc_size on load
Load Long Term Keys stores the user-provided enc_size and later uses
it to size fixed-size stack operations when replying to LE LTK
requests. An enc_size larger than the 16-byte key buffer can therefore
overflow the reply stack buffer.
Reject oversized enc_size values while validating the management LTK
record so invalid keys never reach the stored key state. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: hci_cmd_sync_queue_once() return -EEXIST if exists
hci_cmd_sync_queue_once() needs to indicate whether a queue item was
added, so caller can know if callbacks are called, so it can avoid
leaking resources.
Change the function to return -EEXIST if queue item already exists.
Modify all callsites to handle that. |
| A flaw has been found in TRENDnet TEW-821DAP up to 1.12B01. The impacted element is the function tools_diagnostic of the file /tmp/diagnostic of the component Firmware Udpate. This manipulation causes os command injection. Remote exploitation of the attack is possible. The exploit has been published and may be used. The vendor explains: "That firmware version will only work on our hardware version v1.xR. We have already EOL that product 8 years ago and are no longer selling". This vulnerability only affects products that are no longer supported by the maintainer. |
| A vulnerability has been found in TRENDnet TEW-821DAP 1.12B01. This affects an unknown function of the file /www/cgi/ssi of the component Firmware Update. Such manipulation leads to cleartext transmission of sensitive information. The attack can be executed remotely. This attack is characterized by high complexity. The exploitability is reported as difficult. The exploit has been disclosed to the public and may be used. The vendor explains: "That firmware version will only work on our hardware version v1.xR. We have already EOL that product 8 years ago and are no longer selling". This vulnerability only affects products that are no longer supported by the maintainer. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_helper: pass helper to expect cleanup
nf_conntrack_helper_unregister() calls nf_ct_expect_iterate_destroy()
to remove expectations belonging to the helper being unregistered.
However, it passes NULL instead of the helper pointer as the data
argument, so expect_iter_me() never matches any expectation and all
of them survive the cleanup.
After unregister returns, nfnl_cthelper_del() frees the helper
object immediately. Subsequent expectation dumps or packet-driven
init_conntrack() calls then dereference the freed exp->helper,
causing a use-after-free.
Pass the actual helper pointer so expectations referencing it are
properly destroyed before the helper object is freed.
BUG: KASAN: slab-use-after-free in string+0x38f/0x430
Read of size 1 at addr ffff888003b14d20 by task poc/103
Call Trace:
string+0x38f/0x430
vsnprintf+0x3cc/0x1170
seq_printf+0x17a/0x240
exp_seq_show+0x2e5/0x560
seq_read_iter+0x419/0x1280
proc_reg_read+0x1ac/0x270
vfs_read+0x179/0x930
ksys_read+0xef/0x1c0
Freed by task 103:
The buggy address is located 32 bytes inside of
freed 192-byte region [ffff888003b14d00, ffff888003b14dc0) |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_tunnel: clear skb2->cb[] in ip4ip6_err()
Oskar Kjos reported the following problem.
ip4ip6_err() calls icmp_send() on a cloned skb whose cb[] was written
by the IPv6 receive path as struct inet6_skb_parm. icmp_send() passes
IPCB(skb2) to __ip_options_echo(), which interprets that cb[] region
as struct inet_skb_parm (IPv4). The layouts differ: inet6_skb_parm.nhoff
at offset 14 overlaps inet_skb_parm.opt.rr, producing a non-zero rr
value. __ip_options_echo() then reads optlen from attacker-controlled
packet data at sptr[rr+1] and copies that many bytes into dopt->__data,
a fixed 40-byte stack buffer (IP_OPTIONS_DATA_FIXED_SIZE).
To fix this we clear skb2->cb[], as suggested by Oskar Kjos.
Also add minimal IPv4 header validation (version == 4, ihl >= 5). |
| In the Linux kernel, the following vulnerability has been resolved:
HID: core: Mitigate potential OOB by removing bogus memset()
The memset() in hid_report_raw_event() has the good intention of
clearing out bogus data by zeroing the area from the end of the incoming
data string to the assumed end of the buffer. However, as we have
previously seen, doing so can easily result in OOB reads and writes in
the subsequent thread of execution.
The current suggestion from one of the HID maintainers is to remove the
memset() and simply return if the incoming event buffer size is not
large enough to fill the associated report.
Suggested-by Benjamin Tissoires <bentiss@kernel.org>
[bentiss: changed the return value] |
