| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: mpls: initialize rtm_tos in mpls_getroute()
mpls_getroute() builds the RTM_NEWROUTE reply to an RTM_GETROUTE
request by filling a struct rtmsg allocated from an skb whose data
area is not zeroed (alloc_skb(NLMSG_GOODSIZE, ...)). It sets every
field of the header except rtm_tos:
r = nlmsg_data(nlh);
r->rtm_family = AF_MPLS;
r->rtm_dst_len = 20;
r->rtm_src_len = 0;
r->rtm_table = RT_TABLE_MAIN;
r->rtm_type = RTN_UNICAST;
r->rtm_scope = RT_SCOPE_UNIVERSE;
r->rtm_protocol = rt->rt_protocol;
r->rtm_flags = 0;
struct rtmsg has no padding, so the one uninitialised byte rtm_tos
(offset 3) is copied straight to user space on recvmsg(), leaking a
byte of uninitialised heap memory. This is in contrast to
mpls_dump_route(), which fills the very same header and does set
rtm_tos = 0.
Initialize rtm_tos to 0, matching mpls_dump_route().
Reproduced with KMSAN by adding an MPLS route and issuing a
non-RTM_F_FIB_MATCH RTM_GETROUTE for its label:
BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x36c/0x33f0
_copy_to_iter+0x36c/0x33f0
__skb_datagram_iter+0x196/0x12c0
skb_copy_datagram_iter+0x5b/0x210
netlink_recvmsg+0x37b/0xef0
...
Uninit was created at:
__alloc_skb+0x8ca/0x10e0
mpls_getroute+0x1280/0x3a40
rtnetlink_rcv_msg+0x1138/0x15a0
...
Byte 19 of 64 is uninitialized
(byte 19 = nlmsghdr(16) + rtmsg offset 3 = rtm_tos) |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an integer error when processing DRDA large-object headers. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_sip: widen NAT rewrite delta to s32 in sip_help_tcp()
sip_help_tcp() stores the size change of each NAT-rewritten SIP message
in s16 diff and accumulates it in s16 tdiff, but a single message can
grow by more than S16_MAX while the packet stays under the 65535
enlarge_skb() limit: nf_nat_sip() rewrites every matching URI, and a long
Contact list expands the message by tens of kilobytes. diff then wraps,
and "datalen = datalen + diff - msglen" yields a huge unsigned datalen,
so the next iteration's ct_sip_get_header() reads past the linearized skb
tail.
Widen diff, tdiff and the seq_adjust hook to s32. Both are bounded by the
65535 byte packet limit, and the seqadj core is already s32
(nf_ct_seqadj_set() takes s32), so no previously accepted input is
rejected.
BUG: KASAN: use-after-free in ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
Read of size 1 at addr ffff888010800000 by task ksoftirqd/1/25
ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
sip_help_tcp (net/netfilter/nf_conntrack_sip.c:1694)
nf_confirm (net/netfilter/nf_conntrack_proto.c:183)
nf_hook_slow (net/netfilter/core.c:619)
ip6_output (net/ipv6/ip6_output.c:246)
ip6_forward (net/ipv6/ip6_output.c:690)
ipv6_rcv (net/ipv6/ip6_input.c:351)
__netif_receive_skb_one_core (net/core/dev.c:6212)
process_backlog (net/core/dev.c:6676)
__napi_poll (net/core/dev.c:7735)
net_rx_action (net/core/dev.c:7955)
handle_softirqs (kernel/softirq.c:622)
run_ksoftirqd (kernel/softirq.c:1076)
... |
| In the Linux kernel, the following vulnerability has been resolved:
keys: fix out-of-bounds read in keyring_get_key_chunk()
For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.
The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
keys: make keyring key-chunk byte order agree with keyring_diff_objects()
keyring_get_key_chunk() loads description bytes into the index chunk low
address first, while keyring_diff_objects() numbers the first differing
bit from the low end and folds the absolute byte index into the level
without removing the inline-prefix offset the level already carries.
The two disagree on byte order and bit position, so the array can be
told two keys first differ at a bit that does not differ in the chunk
the walker uses, letting crafted descriptions collide into one node.
Load the chunk in the order keyring_diff_objects() assumes and drop the
inline-prefix length when folding the byte index into the level. This
only changes the in-memory ordering used to place keys within a keyring;
add, search and read of non-colliding keys are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_hashlimit: validate hashtable supports XT_HASHLIMIT_RATE_MATCH
The XT_HASHLIMIT_RATE_MATCH flag mode changes the semantics of the
dsthash_ent structure which represents an entry in the hashtable. There
is a union area which uses a different layout to express the rate match
mode.
Update .checkentry path to validate the XT_HASHLIMIT_RATE_MATCH mode
flag is requested by two or more different rules that refer to the same
hashtable. Otherwise, uninitialized access to the burst field in the
union is possible.
Reject the use of the XT_HASHLIMIT_RATE_MATCH mode flag if set on by
revision less than 3 too. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to obtain sensitive information or cause a denial of service due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: hold the RCU lock across ipv6_chk_addr() in rds_tcp_laddr_check()
rds_tcp_laddr_check() looks up a scoped IPv6 interface with
dev_get_by_index_rcu(), drops the RCU read-side lock, and only then
passes the bare struct net_device * into ipv6_chk_addr().
dev_get_by_index_rcu() only keeps the device alive within the same RCU
read-side section. After rcu_read_unlock(), a concurrent RTM_DELLINK can
free the net_device; ipv6_chk_addr() then dereferences the stale pointer
in __ipv6_chk_addr_and_flags() (e.g. l3mdev_master_dev_rcu(dev)), reading
freed memory.
Keep the RCU read-side lock held across the ipv6_chk_addr() call instead
of dropping it right after the lookup, so the device cannot be freed
while it is in use.
BUG: KASAN: slab-use-after-free in __ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
Read of size 8 at addr ffff8880106ec000 by task exploit/153
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
__ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
ipv6_chk_addr (net/ipv6/addrconf.c:2031 net/ipv6/addrconf.c:1972)
rds_tcp_laddr_check (net/rds/tcp.c:370)
rds_bind (net/rds/bind.c:248)
__sys_bind (net/socket.c:1920)
__x64_sys_bind (net/socket.c:1956)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi: Fix stale-data leak into the SCSI sense buffer
iscsi_scsi_cmd_rsp() copies the sense data of a SCSI Response from the
target-supplied data segment. The segment carries a 2-byte sense length
followed by the sense bytes, so it must hold 2 + senselen bytes, but the
bounds check only requires datalen >= senselen:
senselen = get_unaligned_be16(data);
if (datalen < senselen)
goto invalid_datalen;
memcpy(sc->sense_buffer, data + 2,
min_t(uint16_t, senselen, SCSI_SENSE_BUFFERSIZE));
A target that returns a SCSI Response whose datalen equals senselen
(with senselen <= SCSI_SENSE_BUFFERSIZE) makes the memcpy() from data +
2 read up to two bytes past the received data. Those bytes are stale
conn->data contents and end up in the command's sense buffer, which is
returned to userspace.
Account for the 2-byte sense length prefix in the check. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi_tcp: Bound SCSI Response data segment to the connection buffer
iscsi_tcp_hdr_dissect() receives the data segment of several PDU types
into the fixed-size conn->data buffer, which is allocated for
ISCSI_DEF_MAX_RECV_SEG_LEN (8192) bytes. For the LOGIN_RSP, TEXT_RSP,
REJECT and ASYNC_EVENT opcodes the dissect path already rejects a PDU
whose DataSegmentLength exceeds that buffer.
The SCSI Command Response (ISCSI_OP_SCSI_CMD_RSP) path also copies its
data segment (sense/response data) into conn->data via
iscsi_tcp_data_recv_prep(), but it does so without the same check. The
only upstream bound on in.datalen is conn->max_recv_dlength, the
initiator's advertised MaxRecvDataSegmentLength, which is commonly
negotiated well above 8192 (open-iscsi defaults to 262144). A target
that returns a SCSI Response with a DataSegmentLength between 8193 and
max_recv_dlength therefore overflows the 8192-byte conn->data buffer.
Once the same bound applies, ISCSI_OP_SCSI_CMD_RSP is handled exactly
like those responses: bound the data segment, receive it into conn->data
when present, and otherwise complete the PDU with no data. Fold the
opcode into that case group rather than duplicating the check. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race
Commit fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue
for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock:
the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue,
calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI
devices and waits for the host to become runtime-active. But the host
cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the
drain is blocked on that very handler.
However skipping the drain reintroduces a race: hisi_sas returns from
resume before all PHY UP work and libsas discovery work finish. The
controller may then autosuspend while disks are still waking up. The
disks issue IO to a suspended controller, the IO fails, and the disks
get disabled.
Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT
notification to after sas_drain_work(). By then the host resume is about
to complete, so device removal through device_link no longer blocks on
the resume and the cycle is broken.
With the deadlock gone, restore sas_resume_ha() (the draining variant)
in hisi_sas and remove sas_resume_ha_no_sync().
The reorder is safe for the other libsas consumers (isci, pm8001,
aic94xx, mvsas). During suspend, sas_suspend_devices() calls
sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to
NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a
timed-out phy's disk is immediately rejected by the LLDD before reaching
hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET),
and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both
complete directly via scsi_done() without entering SCSI EH. This is
identical in both the old and new ordering since lldd_dev_gone runs
during suspend, before resume. The reorder only affects when the
PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work()
vs. asynchronous after resume returns), not whether I/O can reach the
device. aic94xx and mvsas do not register any PM ops and never reach
this code path. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Fix number of temperature registers for NCT6116
Unlike NCT6106, NCT6116 only has three temperature registers, and with
it only three temperature source and temperature source configuration
registers. The register addresses match those of NCT6106 and can be
re-used.
The code used a separate array to list the temperature source registers
for NCT6116, but used the size of the NCT6106 register array to set
the number of registers. The NCT6106 register array provides six addresses,
while the temperature source register array for NCT6116 only provides three
addresses. This causes a KASAN report.
BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775]
Read of size 2 at addr ffffffffc19561a6 by task modprobe/954
...
Call Trace:
dump_stack+0x7d/0xa7
print_address_description.constprop.0+0x1c/0x220
? __kasan_kmalloc.constprop.0+0xc9/0xd0
? __kmalloc_node_track_caller+0x194/0x5b0
? nct6775_probe+0x936/0x46f0 [nct6775]
? nct6775_probe+0x936/0x46f0 [nct6775]
...
Fix the problem by hard-coding the number of temperature and temperature
configuration registers to three for NCT6116. Drop the unnecessary
NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (lm90) Only report alarms if driver is ready
Userspace can read sysfs attributes before driver registration is complete,
immediately after devm_hwmon_device_register_with_info() has been called.
At that time, data->hwmon_dev is not yet initialized. This can trigger
a NULL pointer access since lm90_update_device() and with it
lm90_update_alarms_locked() will be called. This call schedules
report_work and lm90_report_alarms(), which passes the still-NULL
data->hwmon_dev to hwmon_notify_event() and triggers a NULL pointer
dereference.
Fix the problem by only scheduling the report and alert workers
data->hwmon_dev is set. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nzxt-smart2) DMA-align output buffer
Sashiko reports:
When send_output_report() calls hid_hw_output_report(), the underlying USB
HID core calls usb_interrupt_msg() which maps this buffer directly for DMA.
When the DMA mapping flushes or invalidates the cacheline, it will corrupt
the adjacent variables (mutex, update_interval) that were modified
concurrently by the CPU. This causes memory corruption due to cacheline
sharing on non-coherent CPU architectures (such as ARM or MIPS). The DMA
API debugging tool (CONFIG_DMA_API_DEBUG) will trigger runtime warnings
for this violation.
Any operation that triggers send_output_report() (like setting a fan speed
or updating the interval) causes the USB DMA mapping. On systems with
non-coherent caches, this structural bug causes immediate and deterministic
memory corruption.
Align the output buffer to ARCH_DMA_MINALIGN to fix the problem. |
| In the Linux kernel, the following vulnerability has been resolved:
net: do not send ICMP/NDISC Redirects when peer allocation fails
When inet_getpeer_v4() or inet_getpeer_v6() fails to allocate a peer entry
under memory pressure or tree size caps, redirect handlers previously fell
back to sending un-rate-limited ICMP/NDISC Redirect messages.
In IPv4, ip_rt_send_redirect() called icmp_send() directly when peer == NULL.
In IPv6, ip6_forward() and ndisc_send_redirect() passed a NULL peer into
inet_peer_xrlim_allow(), which returned true when peer == NULL.
Because ICMP/NDISC Redirects are not part of the default global rate limit
mask (sysctl_icmp_ratemask), sending redirects when peer == NULL creates
an un-rate-limited ICMP packet storm.
Fix this by failing closed in ip_rt_send_redirect(), ip6_forward(), and
ndisc_send_redirect() when peer is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Prevent access to unsupported weight registers
Sashiko reports:
During initialization of the nct6116 chip, the driver sets data->pwm_num
to 5. However, it assigns several NCT6106 register arrays (such as
NCT6106_REG_WEIGHT_DUTY_STEP, NCT6106_REG_WEIGHT_TEMP_SEL, and
NCT6106_REG_WEIGHT_TEMP_*) to data->REG_PWM and data->REG_WEIGHT_TEMP.
These arrays only contain 3 elements.
In nct6775_update_pwm(), the driver iterates up to data->pwm_num. If
data->has_pwm has bits 3 or 4 set (which is structurally possible for
nct6116), the loop attempts to read elements at index 3 and 4 from these
3-element arrays. This results in a global out-of-bounds read, which can
be caught by KASAN.
Furthermore, the driver uses these garbage out-of-bounds values as
hardware register addresses for subsequent read and write operations. This
leads to invalid hardware register access, potentially causing hardware
misconfiguration or system crashes.
The underlying problem is that the chip does support up to five fan
control channels, but only the first three support weight control.
Fix the problem by extending the affected weight register arrays with
zeroed fields. The driver uses zeroed register addresses to determine
if a register is supported or not, and skips accesses for unsupported
registers. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to a buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
forcedeth: fix UAF of txrx_stats in nv_remove
nv_remove() frees the per-CPU txrx_stats before unregister_netdev().
Until unregister completes, ndo_get_stats64, the NAPI/xmit data path,
and nv_close()/drain may still access txrx_stats, leading to a
use-after-free.
Free the stats only after unregister_netdev(). |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (adt7470) Fix busy-loop and I2C flooding in update thread
When userspace configures 'auto_update_interval' to 0 via sysfs, the
background kthread executes schedule_timeout_interruptible(0), which
returns immediately.
If 'num_temp_sensors' is concurrently or previously set to 0, the
msleep_interruptible() delay inside adt7470_read_temperatures() also
becomes 0. This combination forces the background thread into a tight,
unbounded busy-loop, hogging the CPU and flooding the I2C bus with a
continuous stream of transactions.
Fix this vulnerability by raising the lower limit of the clamp_val in
auto_update_interval_store() from 0 to 500 milliseconds. This guarantees
a reasonable minimum sleep window between sensor updates, protecting the
system from intentional or accidental I2C bus denial of service. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (adt7470) Fix divide-by-zero TOCTOU crash in fan speed read
If the fan data becomes 0 between the FAN_DATA_VALID() check and the
FAN_PERIOD_TO_RPM() conversion, it will result in a divide-by-zero crash
due to a race with a concurrent update of the cached fan value.
Fix a TOCTOU issue by reading fan data once. |
