| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: stop hardware after post-start probe failures
wacom_parse_and_register() starts HID hardware before registering inputs
and initializing pad LEDs/remotes. Those later steps can fail, but their
error paths currently release Wacom resources without stopping the HID
hardware.
Route post-hid_hw_start() failures through hid_hw_stop() before
releasing driver resources.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_uart: clear HCI_UART_SENDING when write_work is canceled
HCI_UART_SENDING bit in tx_state means write_work is pending and blocks
queueing it again. Currently this bit is not cleared when canceling the
work in hci_uart_close(), which blocks future writes when device is
reopened later if write_work was pending.
Fix by clearing HCI_UART_SENDING when canceling the work.
Also make clearing of tx_skb safe by using disable_work_sync +
enable_work instead of just cancel_work_sync. hci_uart_flush() purges
the proto tx queue so we can cancel the pending write_work there,
instead of doing it just in hci_uart_close(). Re-enable and possibly
requeue the work after queue flush. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: fix two unsafe bare decodes in decode_lockers()
decode_lockers() in cls_lock_client.c contains two bare decode operations
that allow a malicious or compromised OSD to trigger slab-out-of-bounds
reads:
1. ceph_decode_32(p) at the num_lockers field has no preceding bounds
check. ceph_start_decoding() accepts struct_len=0 as valid -- the
internal ceph_decode_need(p, end, 0, bad) always passes -- so when an
OSD sends struct_len=0, ceph_start_decoding() returns success with
p == end. The immediately following bare ceph_decode_32(p) then reads
4 bytes past the validated buffer boundary. The garbage value is
passed directly to kzalloc_objs() as the locker count.
The sibling function decode_watchers() in osd_client.c already uses
ceph_decode_32_safe() after its own ceph_start_decoding() call.
decode_lockers() was the only site using the bare variant.
2. ceph_decode_8(p) after the decode_locker() loop has no preceding
bounds check. If an OSD crafts num_lockers such that the loop
advances p exactly to end, the subsequent bare ceph_decode_8(p) reads
one byte past the validated buffer boundary. The result is passed
directly into *type, which is used as a lock type discriminator by
callers, giving an OSD-controlled one-byte OOB read with direct
influence over the lock type field.
Fix both by replacing bare operations with their safe variants:
ceph_decode_32(p) -> ceph_decode_32_safe(p, end, *num_lockers,
err_inval)
ceph_decode_8(p) -> ceph_decode_8_safe(p, end, *type,
err_free_lockers)
The goto targets differ intentionally:
err_inval: is a new label returning -EINVAL directly. It is used for
the pre-allocation failure path where *lockers is not yet allocated
and must not be passed to ceph_free_lockers().
err_free_lockers: is the existing label. It is used for the
post-allocation failure path where *lockers is allocated and must
be freed.
ret is set to -EINVAL before ceph_decode_8_safe() so that
err_free_lockers returns the correct error code on bounds violation.
Without this, err_free_lockers would return a stale ret value (0 from
the successful decode_locker() loop), silently swallowing the error.
-EINVAL is correct for both failure paths. The data received from the
OSD is structurally malformed. -ENOMEM would misrepresent the failure
class to callers and to stable@ backporters triaging error paths.
Attacker model: a malicious or compromised OSD in a multi-tenant Ceph
deployment can trigger this against any kernel client that issues the
lock.get_info class method (e.g. during RBD exclusive lock acquisition).
[ idryomov: trim changelog, formatting ] |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: resample the data fork mapping after cycling ILOCK
xfs_reflink_fill_{cow_hole,delalloc} are both presented with an inode,
a data fork mapping, and a cow fork mapping. Unfortunately, these two
helpers cycle the ILOCK to grab a transaction, which means that the
mappings are stale as soon as we reacquire the ILOCK. Currently we
refresh the cow fork mapping by re-calling xfs_find_trim_cow_extent, but
we don't refresh the data fork mapping beforehand, which means that the
xfs_bmap_trim_cow in that function queries the refcount btree about the
wrong physical blocks and returns an inaccurate value in *shared.
If *shared is now false, the directio write proceeds with a stale data
fork mapping. Fix this by querying the data fork mapping if the
sequence counter changes across the ILOCK cycle. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: amlogic - avoid double cleanup in meson_crypto_probe()
When meson_allocate_chanlist() fails after a partial allocation, it already
unwinds the allocated chanlist state through its local error path.
meson_crypto_probe() then jump to error_flow and calls
meson_free_chanlist() again, causing the same per-flow resources to be torn
down twice. In the reproduced failure path, the second teardown
re-entered crypto_engine_exit() on an already destroyed worker and KASAN
reported a slab-use-after-free in kthread_destroy_worker().
Prevent double-free by handling partial allocation failures locally within
meson_allocate_chanlist() and skipping the outer cleanup path.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available.
The bug was reproduced in a QEMU x86_64 guest booted with KASAN on v7.1,
using the reproducer under tools/testing/meson_crypto_probe. The reproducer
forces the second dma_alloc_attrs() call in the gxl-crypto probe path to
return NULL, making meson_allocate_chanlist() fail after partial
initialization. On the unpatched kernel this reliably triggered a
slab-use-after-free. With this fix applied, the same reproducer no longer
emits any KASAN report and the probe fails cleanly with -ENOMEM.
==================================================================
BUG: KASAN: slab-use-after-free in kthread_destroy_worker+0xb2/0xd0
Read of size 8 at addr ff1100010c057a68 by task insmod/265
CPU: 1 UID: 0 PID: 265 Comm: insmod Tainted: G O 7.1.0-rc2-00376-g810af9adc907-dirty #10 PREEMPT(lazy)
Tainted: [O]=OOT_MODULE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0xa0
print_report+0xcb/0x5e0
? __virt_addr_valid+0x21d/0x3f0
? kthread_destroy_worker+0xb2/0xd0
? kthread_destroy_worker+0xb2/0xd0
kasan_report+0xca/0x100
? kthread_destroy_worker+0xb2/0xd0
kthread_destroy_worker+0xb2/0xd0
meson_crypto_probe+0x4d0/0xc10 [amlogic_gxl_crypto]
platform_probe+0x99/0x140
really_probe+0x1c6/0x6a0
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x248/0x310
? acpi_driver_match_device+0xb0/0x100
driver_probe_device+0x48/0x210
? __pfx___device_attach_driver+0x10/0x10
__device_attach_driver+0x160/0x320
bus_for_each_drv+0x104/0x190
? __pfx_bus_for_each_drv+0x10/0x10
? _raw_spin_unlock_irqrestore+0x2c/0x50
__device_attach+0x19d/0x3b0
? __pfx___device_attach+0x10/0x10
? do_raw_spin_unlock+0x53/0x220
device_initial_probe+0x78/0xa0
bus_probe_device+0x5b/0x130
device_add+0xcfd/0x1430
? __pfx_device_add+0x10/0x10
? insert_resource+0x34/0x50
? lock_release+0xc9/0x290
platform_device_add+0x24e/0x590
? __pfx_meson_crypto_probe_repro_init+0x10/0x10 [meson_crypto_probe_repro]
meson_crypto_probe_repro_init+0x330/0xff0 [meson_crypto_probe_repro]
do_one_initcall+0xc0/0x450
? __pfx_do_one_initcall+0x10/0x10
? _raw_spin_unlock_irqrestore+0x2c/0x50
? __create_object+0x59/0x80
? kasan_unpoison+0x27/0x60
do_init_module+0x27b/0x7d0
? __pfx_do_init_module+0x10/0x10
? kasan_quarantine_put+0x84/0x1d0
? kfree+0x32c/0x510
? load_module+0x561e/0x5ff0
load_module+0x54fe/0x5ff0
? __pfx_load_module+0x10/0x10
? security_file_permission+0x20/0x40
? kernel_read_file+0x23d/0x6e0
? mmap_region+0x235/0x4a0
? __pfx_kernel_read_file+0x10/0x10
? __file_has_perm+0x2c0/0x3e0
init_module_from_file+0x158/0x180
? __pfx_init_module_from_file+0x10/0x10
? __lock_acquire+0x45a/0x1ba0
? idempotent_init_module+0x315/0x610
? lock_release+0xc9/0x290
? lock
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: Fix error code in smb2_aead_req_alloc()
The "*num_sgs" variable is a u32 so "ERR_PTR(*num_sgs)" doesn't work.
We would have to do something similar to the previous line where it's
cast to int and then long. However, it's simpler to store the return in
an int ret variable.
This bug would eventually result in a crash when dereference the invalid
error pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix double-free in SMB2_close() replay
A response-bearing attempt can return a replayable error and free its
response buffer. If SMB2_close_init() fails before the next send, cleanup
retains the previous buffer type and frees that response again.
Reset response bookkeeping before each attempt to prevent the stale free. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix a use-after-free problem in rxe_mmap
rxe_mmap() removes a rxe_mmap_info struct from the pending_mmaps list
and releases pending_lock while the struct's kref is still at 1:
list_del_init(&ip->pending_mmaps);
spin_unlock_bh(&rxe->pending_lock); /* ref == 1, no lock held */
ret = remap_vmalloc_range(vma, ip->obj, 0); /* walks PTEs */
[...]
rxe_vma_open(vma); /* kref_get, ref → 2 */
remap_vmalloc_range_partial() walks PTEs without any lock.
A concurrent DESTROY_CQ ioctl on another CPU calls:
kref_put(&q->ip->ref, rxe_mmap_release) /* ref 1→0 */
vfree(ip->obj) /* clears vmalloc PTEs mid-walk */
kfree(ip) /* frees rxe_mmap_info */
This yields:
1. Kernel crash, vmalloc_to_page() returns NULL when vfree wins the
per-PTE race -> vm_insert_page(NULL) → GPF in validate_page_before_insert
2. Page UAF, vmalloc_to_page() reads a stale PTE before vfree clears
it. User VMA holds a PTE to a free'd page which might eventually get
reallocated later by vmalloc which allows the attacker to get a clean
page-level UAF.
It is worth noting that even though a page-level UAF is possible given
the strong primitive, it is statistically very difficult to achieve
given the very short time window (after the last insert_page and before
the kref_get).
The call trace are as below:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 0 UID: 1000 PID: 413 Comm: poc Not tainted 7.0.0-rc5-dirty #28 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:validate_page_before_insert+0x32/0x300
Code: e5 41 57 41 56 49 89 fe 41 55 41 54 53 48 89 f3 e8 93 b5 a3 ff 48 8d 7b 08 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 7b 02 00 00 4c 8b 63 08 31 ff 4d 89 e5 41 83 e5
RSP: 0018:ffff88811b15f2f0 EFLAGS: 00000202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000008
RBP: ffff88811b15f318 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8881181eee00
R13: 0000000000000000 R14: ffff8881181eee00 R15: ffff8881181eee20
FS: 00007b1e000f76c0(0000) GS:ffff8884268e0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007b1e00a24ac0 CR3: 0000000116eb3000 CR4: 00000000000006f0
Call Trace:
<TASK>
insert_page+0x8f/0x190
? __pfx_insert_page+0x10/0x10
? kasan_save_alloc_info+0x38/0x60
vm_insert_page+0x2e7/0x400
remap_vmalloc_range_partial+0x212/0x3e0
remap_vmalloc_range+0x6e/0xb0
? __kasan_check_write+0x14/0x30
rxe_mmap+0x2e9/0x5d0
ib_uverbs_mmap+0x1ad/0x2c0
__mmap_region+0x12c2/0x2ad0
? __pfx___mmap_region+0x10/0x10
? __sanitizer_cov_trace_switch+0x58/0xb0
? mas_prev_slot+0x360/0x39c0
? __sanitizer_cov_trace_switch+0x58/0xb0
? mas_next_slot+0x1e5b/0x2f40
? __sanitizer_cov_trace_cmp8+0x18/0x30
? unmapped_area_topdown+0x4dd/0x610
? kfree+0x1b1/0x440
? free_cpumask_var+0x16/0x30
? __kasan_slab_free+0x7d/0xa0
? __sanitizer_cov_trace_cmp8+0x18/0x30
mmap_region+0x2e6/0x3c0
do_mmap+0xa3e/0x12a0
? __pfx_do_mmap+0x10/0x10
? __kasan_check_write+0x14/0x30
? down_write_killable+0xba/0x160
? __pfx_down_write_killable+0x10/0x10
? __sanitizer_cov_trace_cmp4+0x16/0x30
vm_mmap_pgoff+0x2d4/0x4a0
? __pfx_vm_mmap_pgoff+0x10/0x10
? fget+0x1bf/0x270
ksys_mmap_pgoff+0x40c/0x690
? __sanitizer_cov_trace_const_cmp4+0x16/0x30
? __pfx_ksys_mmap_pgoff+0x10/0x10
? __kasan_check_write+0x14/0x30
? _raw_spin_trylock+0xbb/0x130
? __pfx__raw_spin_trylock+0x10/0x10
__x64_sys_mmap+0x135/0x1e0
x64_sys_c
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: fix sk_dst_cache double-free in xfrm_user_policy()
xfrm_user_policy() clears the socket dst cache with __sk_dst_reset(),
i.e. the non-atomic __sk_dst_set(sk, NULL): it reads sk_dst_cache with
rcu_dereference_protected(), stores NULL and dst_release()s the old dst.
That is only safe if no other thread modifies sk_dst_cache concurrently.
For a connected UDP socket that does not hold: the transmit fast path
(udp_sendmsg -> sk_dst_check -> sk_dst_reset) resets the cache locklessly
with an atomic xchg(). A per-socket policy change racing a send can make
both sides observe the same old dst and each dst_release() it, dropping
the socket's single reference twice and freeing the xfrm_dst bundle while
it is still referenced:
BUG: KASAN: slab-use-after-free in dst_release
Write of size 4 at addr ffff88801897b6c0 by task exploit/155
Call Trace:
...
dst_release (... ./include/linux/rcuref.h:109)
xfrm_user_policy (./include/net/sock.h:2239 ./include/net/sock.h:2256 net/xfrm/xfrm_state.c:3053)
do_ip_setsockopt (net/ipv4/ip_sockglue.c:1347)
ip_setsockopt (net/ipv4/ip_sockglue.c:1417)
do_sock_setsockopt (net/socket.c:2368)
__sys_setsockopt (net/socket.c:2393)
__x64_sys_setsockopt (net/socket.c:2396)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
Reachable by an unprivileged user via a user+network namespace.
Use the atomic sk_dst_reset() so the cache is cleared and released with a
single xchg(): whichever side wins releases the dst once, the other sees
NULL and does nothing. Behaviour is otherwise unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm6: clear dst.dev on error to avoid double netdev_put in xfrm6_fill_dst()
On the error path where in6_dev_get(dev) returns NULL, xfrm6_fill_dst()
releases the device reference with netdev_put() but leaves
xdst->u.dst.dev set. dst_destroy() later calls netdev_put(dst->dev)
again, so the same net_device reference is released twice, underflowing
its refcount (ref_tracker WARNING + "unregister_netdevice: waiting for
<dev> to become free").
Clear xdst->u.dst.dev after the netdev_put(), the same way the XFRM
device-offload paths xfrm_dev_state_add() and xfrm_dev_policy_add() in
net/xfrm/xfrm_device.c NULL ->dev when releasing the reference on error.
ref_tracker: reference already released.
ref_tracker: allocated in:
xfrm6_fill_dst (net/ipv6/xfrm6_policy.c:86)
...
udpv6_sendmsg (net/ipv6/udp.c:1696)
...
ref_tracker: freed in:
xfrm6_fill_dst (net/ipv6/xfrm6_policy.c:90)
...
WARNING: lib/ref_tracker.c:322 at ref_tracker_free+0x58b/0x780
dst_destroy (net/core/dst.c:115)
rcu_core
handle_softirqs
... |
| In the Linux kernel, the following vulnerability has been resolved:
nexthop: initialize extack in nh_res_bucket_migrate()
nh_res_bucket_migrate() passes an uninitialized netlink_ext_ack to
call_nexthop_res_bucket_notifiers(). When
nh_notifier_res_bucket_info_init() fails (e.g. the kzalloc returns
-ENOMEM), the error is propagated back before any notifier sets
extack._msg, and the error path formats the stale pointer with
pr_err_ratelimited("%s\n", extack._msg). With CONFIG_INIT_STACK_NONE
this dereferences uninitialized stack memory:
Oops: general protection fault, probably for non-canonical address ...
KASAN: maybe wild-memory-access in range [...]
RIP: 0010:string (lib/vsprintf.c:730)
vsnprintf (lib/vsprintf.c:2945)
_printk (kernel/printk/printk.c:2504)
nh_res_bucket_migrate (net/ipv4/nexthop.c:1816)
nh_res_table_upkeep (net/ipv4/nexthop.c:1866)
rtm_new_nexthop (net/ipv4/nexthop.c:3323)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
netlink_sendmsg (net/netlink/af_netlink.c:1900)
Kernel panic - not syncing: Fatal exception
Zero-initialize extack so _msg is NULL on error paths that never set it. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: tcp: fix double sock release on batch realloc
bpf_iter_tcp_batch() releases the current batch via
bpf_iter_tcp_put_batch(), which drops the socket refs and rewrites
each slot with the socket cookie, then grows the batch. cur_sk/end_sk
are kept for bpf_iter_tcp_resume(), but on realloc failure the function
returns ERR_PTR() before resume runs, leaving cur_sk < end_sk over
slots that now hold cookies rather than sock pointers.
bpf_iter_tcp_seq_stop() then calls bpf_iter_tcp_put_batch() again and
dereferences a cookie as a struct sock.
Empty the batch on the failure path so stop() does not release it
again. The sockets were already freed by the first
bpf_iter_tcp_put_batch(), so nothing leaks, and a later read() rescans
the bucket from the start instead of skipping it. The sibling
GFP_NOWAIT failure path still holds real socket references and is left
for stop() to release.
BUG: KASAN: null-ptr-deref in __sock_gen_cookie
Read of size 8 at addr 0000000000000059 by task exploit
...
__sock_gen_cookie (net/core/sock_diag.c:28)
bpf_iter_tcp_put_batch (net/ipv4/tcp_ipv4.c:2918)
bpf_iter_tcp_seq_stop (net/ipv4/tcp_ipv4.c:3270)
bpf_seq_read (kernel/bpf/bpf_iter.c:205)
vfs_read (fs/read_write.c:572)
ksys_read (fs/read_write.c:716)
do_syscall_64
entry_SYSCALL_64_after_hwframe
Kernel panic - not syncing: Fatal exception |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: tear down new links on vif update error path
When ieee80211_vif_update_links() adds new links it allocates a link
container for each and calls ieee80211_link_init() (which registers the
per-link debugfs files with file->private_data pointing into the container)
and ieee80211_link_setup(). If the subsequent drv_change_vif_links() fails,
the error path restores the old pointers and jumps to 'free', which frees
the new containers but never removes their debugfs entries or stops the
links. The debugfs files survive with file->private_data dangling at the
freed container, so a later open()+read() (e.g. link-1/txpower)
dereferences freed memory in ieee80211_if_read_link(), a use-after-free.
The removal path already dismantles links correctly via
ieee80211_tear_down_links(), which removes each link's keys and debugfs
entries and calls ieee80211_link_stop(); the add path on the error branch
does not. Commit be1ba9ed221f ("wifi: mac80211: avoid weird state in error
path") hardened this same error path for the link-removal case
(new_links == 0) but left the newly-added links' teardown unaddressed.
drv_change_vif_links() can fail at runtime on MLO drivers (internal
allocation / queue / firmware command failures).
Remove the new links' debugfs entries and stop them before freeing.
BUG: KASAN: slab-use-after-free in ieee80211_if_read_link (net/mac80211/debugfs_netdev.c:127)
Read of size 8 at addr ffff888011290000 by task exploit/145
Call Trace:
...
ieee80211_if_read_link (net/mac80211/debugfs_netdev.c:127)
short_proxy_read (fs/debugfs/file.c:373)
vfs_read (fs/read_write.c:572)
ksys_read (fs/read_write.c:716)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
...
Oops: general protection fault, probably for non-canonical address 0xdffffc000000000a
RIP: 0010:ieee80211_if_read_link (net/mac80211/debugfs_netdev.c:127)
Kernel panic - not syncing: Fatal exception |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix fils_discovery double free on alloc failure
ieee80211_set_fils_discovery() calls kfree_rcu() on the old template
before allocating the replacement. If the kzalloc() then fails, it
returns -ENOMEM while link->u.ap.fils_discovery still points at the
object already queued for freeing. A later update or AP teardown
(ieee80211_stop_ap()) re-queues that same rcu_head; the second free is
caught by KASAN when the RCU sheaf is processed in softirq:
BUG: KASAN: double-free in rcu_free_sheaf (mm/slub.c:5850)
Free of addr ffff88800c065280 by task swapper/0/0
...
__rcu_free_sheaf_prepare (mm/slub.c:2634 mm/slub.c:2940)
rcu_free_sheaf (mm/slub.c:5850)
rcu_core (kernel/rcu/tree.c:2617 kernel/rcu/tree.c:2869)
handle_softirqs (kernel/softirq.c:622)
The buggy address belongs to the cache kmalloc-96 of size 96
Queue the old object for kfree_rcu() only after the new one is published,
matching ieee80211_set_probe_resp() and ieee80211_set_s1g_short_beacon(). |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: don't free the ASCONF's own transport in DEL-IP processing
sctp_process_asconf() caches the transport the ASCONF chunk is processed
against in asconf->transport (== chunk->transport, set once in sctp_rcv()).
For an ASCONF located through its Address Parameter by
__sctp_rcv_asconf_lookup(), that cached transport corresponds to the
Address Parameter, which need not be the packet's source address.
sctp_process_asconf_param() rejects a DEL-IP for the packet source address
(ADDIP D8, SCTP_ERROR_DEL_SRC_IP), but nothing protects asconf->transport.
A single ASCONF can therefore carry, in order:
[Address Parameter L] [DEL-IP L] [DEL-IP 0.0.0.0]
where L differs from the source. The DEL-IP for L passes the D8 check and
calls sctp_assoc_rm_peer() on the transport that asconf->transport still
points at, freeing it (RCU-deferred). The following wildcard DEL-IP then
reuses the now-dangling asconf->transport in sctp_assoc_set_primary() and
sctp_assoc_del_nonprimary_peers(): set_primary() dereferences the freed
transport (->ipaddr, ->state) and plants the dangling pointer into
asoc->peer.primary_path / active_path, and del_nonprimary_peers(), keeping
only the pointer that is no longer on the list, removes every real
transport, leaving the association with a transport_count of 0 and
primary_path/active_path pointing at freed memory.
Reject a DEL-IP that targets the transport the ASCONF is being processed
against, mirroring the existing source-address guard, so the wildcard
branch can never reuse a freed transport. |
| In the Linux kernel, the following vulnerability has been resolved:
rhashtable: clear stale iter->p on table restart
rhashtable_walk_start_check() has two restart paths when resuming a walk.
When iter->walker.tbl is valid, it re-validates iter->p against the table
and sets iter->p = NULL if the object is gone. When iter->walker.tbl is
NULL (table was freed during resize), it resets slot and skip but forgets
to clear iter->p.
rhashtable_walk_next() then dereferences the stale iter->p, reading
freed memory. This is a use-after-free.
Any caller that does multi-fragment rhashtable walks across
walk_stop/walk_start boundaries is affected. Concrete cases include
netlink_diag (__netlink_diag_dump in net/netlink/diag.c) and TIPC
(tipc_nl_sk_walk in net/tipc/socket.c).
Crash stack (netlink_diag):
BUG: KASAN: slab-use-after-free in rhashtable_walk_next+0x365/0x3c0
Read of size 8 at addr ffff88801a9d2438 (freed kmalloc-2k, offset 1080)
Call Trace:
rhashtable_walk_next+0x365/0x3c0 (lib/rhashtable.c:1016)
__netlink_diag_dump+0x160/0x760 (net/netlink/diag.c:122)
netlink_diag_dump+0xc2/0x240
netlink_dump+0x5bc/0x1270
netlink_recvmsg+0x7a3/0x980
sock_recvmsg+0x1bc/0x200
__sys_recvfrom+0x1d4/0x2c0 |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nVMX: Hide shadow VMCS right after VMCLEAR
free_nested() frees the shadow VMCS while vmcs01 still points to it. But
because it is asynchronous with respect to loaded_vmcs_clear(), the vCPU
might migrate before the pointer is cleared and __loaded_vmcs_clear()
may then execute VMCLEAR.
The VMCS needs to stay attached until its explicit VMCLEAR completes, but
then it can be hidden and the page safely freed. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Check for invalid/obsolete root *after* making MMU pages available
Check for a "stale" page fault, i.e. for an invalid and/or obsolete root,
after making MMU pages available for the shadow MMU. If reclaiming shadow
pages zaps an in-use root, i.e. marks it invalid, then KVM will attempt to
map memory into an invalid root. On its own, populating an invalid root is
"fine", but because child shadow pages inherit their parent's role, any
children created during the map/fetch will be created as invalid pages,
thus violating KVM's invariant that invalid pages are never on the list of
active MMU pages.
Note, the underlying flaw has existed since KVM first started tracking
invalid roots in 2008 (commit 2e53d63acba7, "KVM: MMU: ignore zapped root
pagetables"), but the true badness only came along in 2020 (Linux 5.9)
with the invariant that invalid shadow pages can't be on the list of
active pages.
Note #2, inheriting role.invalid when creating child shadow pages is also
far from ideal; that flaw will be addressed separately. |
| In the Linux kernel, the following vulnerability has been resolved:
posix-cpu-timers: Prevent UAF caused by non-leader exec() race
Wongi and Jungwoo decoded and reported a non-leader exec() related race
which can result in an UAF:
sys_timer_delete() exec()
posix_cpu_timer_del()
// Observes old leader
p = pid_task(pid, pid_type); de_thread()
switch_leader();
release_task(old_leader)
__exit_signal(old_leader)
sighand = lock(old_leader, sighand);
posix_cpu_timers*_exit();
sighand = lock_task_sighand(p) unhash_task(old_leader);
sh = lock(p, sighand) old_leader->sighand = NULL;
unlock(sighand);
(p->sighand == NULL)
unlock(sh)
return NULL;
// Returns without action
if(!sighand)
return 0;
free_posix_timer();
This is "harmless" unless the deleted timer was armed and enqueued in
p->signal because on exec() a TGID targeted timer is inherited.
As sys_timer_delete() freed the underlying posix timer object
run_posix_cpu_timers() or any timerqueue related add/delete operations on
other timers will access the freed object's timerqueue node, which results
in an UAF.
There is a similar problem vs. posix_cpu_timer_set(). For regular posix
timers it just transiently returns -ESRCH to user space, but for the use
case in do_cpu_nanosleep() it's the same UAF just that the k_itimer is
allocated on the stack.
Also posix_cpu_timer_rearm() fails to rearm the timer, which means it stops
to expire.
While debating solutions Frederic pointed out another problem:
posix_cpu_timer_del(tmr)
__exit_signal(p)
posix_cpu_timers*_exit(p);
unhash_task(p);
p->sighand = NULL;
sh = lock_task_sighand(p)
sighand = p->sighand;
if (!sighand)
return NULL;
lock(sighand);
if (!sh)
WARN_ON_ONCE(timer_queued(tmr));
On weakly ordered architectures it is not guaranteed that
posix_cpu_timer_del() will observe the stores in posix_cpu_timers*_exit()
when p->sighand is observed as NULL, which means the WARN() can be a false
positive.
Solve these issues by:
1) Changing the store in __exit_signal() to smp_store_release().
2) Adding a smp_acquire__after_ctrl_dep() into the !sighand path
of lock_task_sighand().
3) Creating a helper function for looking up the task and locking sighand
which does not return when sighand == NULL. Instead it retries the
task lookup and only if that fails it gives up.
4) Using that helper in the three affected functions.
#1/#2 ensures that the reader side which observes sighand == NULL also
observes all preceeding stores, i.e. the stores in posix_cpu_timers*_exit()
and the ones in unhash_task().
#3 ensures that the above described non-leader exec() situation is handled
gracefully. When the task lookup returns the old leader, but sighand ==
NULL then it retries. In the non-leader exec() case the subsequent task
lookup will observe the new leader due to #1/#2. In normal exit() scenarios
the subsequent lookup fails.
When the task lookup fails, the function also checks whether the timer is
still enqueued and issues a warning if that's the case. Unfortunately there
is nothing which can be done about it, but as the task is already not
longer visible the timer should not be accessed anymore. This check also
requires memory ordering, which is not provided when the first lookup
fails. To achieve that the check is preceeded by a smp_rmb() which pairs
with the smp_wmb() in write_seqlock() in __exit_signal(). That ensures that
the stores in posix_cpu_timers*_exit() are visible.
The history of the non-leader exec() issue goes back to the early days of
posix CPU timers, which stored a pointer to the group leader task in the
timer. That obviously fails when a non-leader exec() switches the leader.
commit e0a70217107e ("posix-cpu-timers: workaround to suppress the problems
with mt exec") added a temporary workaround for that in 2010 which surv
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
s390/pkey: Check length in PKEY_VERIFYPROTK ioctl
Explicitly check the buffer length request structure provided by
user-space and fail, if it exceeds the buffer size. |
