| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: mediatek: Fix IRQ domain leak when port fails to enable
When mtk_pcie_enable_port() fails, mtk_pcie_port_free() removes the port
from pcie->ports and frees the port structure. However, the IRQ domains set
up earlier by mtk_pcie_init_irq_domain() are never freed.
Fix this by refactoring mtk_pcie_irq_teardown() into a per-port helper,
mtk_pcie_irq_teardown_port(), and calling it from mtk_pcie_setup() when
mtk_pcie_enable_port() fails. Since the IRQ teardown must only happen in
the probe error path (during resume, child devices may have active MSI
mappings and the NOIRQ context prohibits sleeping locks),
mtk_pcie_enable_port() is changed to return an error code so callers can
distinguish the two paths and act accordingly.
This issue was reported by Sashiko while reviewing the EcoNet EN7528 SoC
support series. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: Fix sleep in atomic context in xhci_free_streams()
When a USB device with active stream endpoints is disconnected,
xhci_free_streams() is called from the hub_event workqueue to
free the stream resources. It calls xhci_free_stream_info()
while holding xhci->lock with irqs disabled.
xhci_free_stream_info() invokes xhci_free_stream_ctx(), which
calls dma_free_coherent() for large stream context arrays.
dma_free_coherent() can sleep (e.g. via vunmap), triggering
a BUG when called from atomic context.
Call trace:
dma_free_attrs+0x174/0x220
xhci_free_stream_info+0xd0/0x11c
xhci_free_streams+0x278/0x37c
usb_free_streams+0x98/0xc0
usb_unbind_interface+0x1b8/0x2f8
device_release_driver_internal+0x1d4/0x2cc
device_release_driver+0x18/0x28
bus_remove_device+0x160/0x1a4
device_del+0x1ec/0x350
usb_disable_device+0x98/0x214
usb_disconnect+0xf0/0x35c
hub_event+0xab4/0x19ec
process_one_work+0x278/0x63c
Fix this by saving the stream_info pointers and clearing the
ep references under the lock, then calling xhci_free_stream_info()
outside the lock where sleeping is allowed. |
| In the Linux kernel, the following vulnerability has been resolved:
rust_binder: clear freeze listener on node removal
Generally userspace is supposed to explicitly clear freeze listeners
before they drop the refcount on the node ref to zero, but there's
nothing forcing that. Currently, in this scenario the freeze listener
remains in the freeze_listeners rbtree and in the remote node's freeze
listener list, even though the ref for which the listener is registered
is gone. This could potentially lead to a memory leak due to a refcount
cycle. Thus, remove the freeze listener in this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix UAF in binder_thread_release()
When a thread exits, binder_thread_release() walks its transaction stack
to clear the t->from and t->to_proc that correspond with the exiting
thread. However, a process dying in parallel might attempt to kfree some
of these transactions. And if one of them has no associated t->to_proc,
the t->to_proc->inner_lock will not be acquired.
This means that transaction accesses in binder_thread_release() after
t->to_proc has been cleared might race with binder_free_transaction()
and cause a use-after-free error as reported by KASAN:
==================================================================
BUG: KASAN: slab-use-after-free in binder_thread_release+0x5d0/0x798
Write of size 8 at addr ffff000016627500 by task X/715
CPU: 17 UID: 0 PID: 715 Comm: X Not tainted 7.1.0-rc5-00149-g8fde5d1d47f6 #30 PREEMPT
Hardware name: linux,dummy-virt (DT)
Call trace:
binder_thread_release+0x5d0/0x798
binder_ioctl+0x12c0/0x299c
[...]
Allocated by task 717 on cpu 18 at 67.267803s:
__kasan_kmalloc+0xa0/0xbc
__kmalloc_cache_noprof+0x174/0x444
binder_transaction+0x554/0x8150
binder_thread_write+0xa30/0x4354
binder_ioctl+0x20f0/0x299c
[...]
Freed by task 202 on cpu 18 at 90.416221s:
__kasan_slab_free+0x58/0x80
kfree+0x1a0/0x4a4
binder_free_transaction+0x150/0x294
binder_send_failed_reply+0x398/0x6d8
binder_release_work+0x3e4/0x4ec
binder_deferred_func+0xbd8/0x104c
[...]
==================================================================
In order to avoid this, make sure that binder_free_transaction() reads
the t->to_proc under the transaction lock. This will serialize the
transaction release with the accesses in binder_thread_release(). Plus,
it matches the documented locking rules for @to_proc. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/mlx5: Fix racy bitfields and tighten struct layout
Bitfield operations are not atomic, they use a read-modify-write
pattern, therefore we should be careful not to pack bitfields that
can be concurrently updated into the same storage unit.
This split takes a binary approach: flags that are only modified
pre/post open/close remain bitfields, flags modified from user
action, including actions that reach across to another device (ex.
reset) use dedicated storage units.
Note mlx5_vhca_page_tracker.status is relocated to fill the alignment
hole this split exposes.
Bitfield justifications:
migrate_cap: written only in mlx5vf_cmd_set_migratable() at probe
chunk_mode: written only in mlx5vf_cmd_set_migratable() at probe
mig_state_cap: written only in mlx5vf_cmd_set_migratable() at probe
Dedicated storage units:
mdev_detach: written in the VF attach/detach event notifier
mlx5fv_vf_event() at runtime
log_active: written in mlx5vf_start_page_tracker()/
mlx5vf_stop_page_tracker() during runtime dirty tracking
deferred_reset: written in mlx5vf_state_mutex_unlock()/
mlx5vf_pci_aer_reset_done() during runtime reset handling
is_err: set by tracker error handling and dirty-log polling at runtime
object_changed: set by tracker event handling and cleared by dirty-log
polling at runtime |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/pci: Latch disable_idle_d3 per device
When disable_idle_d3 was introduced in vfio-pci, it directly manipulated
the device power state with pci_set_power_state(). There were no
refcounts to maintain or balanced operations, we could unconditionally
bring the device to D0 and conditionally move it to D3hot. Therefore
the module parameter was made writable.
Later, in commit c61302aa48f7 ("vfio/pci: Move module parameters to
vfio_pci.c"), as part of the vfio-pci-core split, the writable aspect
of the module parameter was nullified. The parameter value could still
be changed through sysfs, but the vfio-pci driver latched the values
into vfio-pci-core globals at module init. Loading the vfio-pci module,
or unloading and reloading, with non-default or different values could
change the globals relative to existing devices bound to vfio-pci
variant drivers.
Runtime PM was introduced in commit 7ab5e10eda02 ("vfio/pci: Move the
unused device into low power state with runtime PM"), which marks the
point where power states became refcounted. PM get and put operations
need to be balanced, but the same module operations noted above can
change the global variables relative to those devices already bound to
vfio-pci variant drivers. This introduces a window where PM operations
can now become unbalanced.
To resolve this with a narrow footprint for stable backports, the
disable_idle_d3 flag is latched into the vfio_pci_core_device at the
time of initialization, such that the device always operates with a
consistent value.
NB. vfio_pci_dev_set_try_reset() now unconditionally raises the
runtime PM usage count around bus reset to account for disable_idle_d3
becoming a per-device rather than global flag. When this flag is set,
the additional get/put pair is harmless and allows continued use of the
shared vfio_pci_dev_set_pm_runtime_get() helper. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: gus: check snd_ctl_new1() return value
snd_ctl_new1() can return NULL when memory allocation fails.
snd_gf1_pcm_volume_control() does not check the return value before
dereferencing kctl->id.index, which can lead to a NULL pointer
dereference.
Add a NULL check after snd_ctl_new1() and return -ENOMEM if it fails. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: compress: Fix task creation error unwind
snd_compr_task_new() allocates the driver task before validating the
returned DMA buffers and reserving file descriptors. When either of
those later steps fails, the core frees its task wrapper and DMA-buffer
references without calling the driver's task_free() callback. Any
driver resources allocated by task_create() are therefore leaked.
The dual-fd allocation path also jumps to cleanup without storing the
negative get_unused_fd_flags() result in retval. Since retval still
contains the successful task_create() return value, TASK_CREATE can
incorrectly report success although the task was discarded.
Preserve the fd allocation errors and call task_free() when failure
occurs after a successful task_create() callback. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: virtio: Validate control metadata from the device
virtio-snd control handling trusts the device-provided control type and
value count returned by the device.
That metadata is then used directly to index g_v2a_type_map[] in
virtsnd_kctl_info(), and to size loops and memcpy() operations in
virtsnd_kctl_get() and virtsnd_kctl_put() against fixed-size
virtio_snd_ctl_value and snd_ctl_elem_value arrays.
A buggy or malicious device can therefore trigger out-of-bounds access by
advertising an invalid control type or an oversized value count.
Validate control type and count once in virtsnd_kctl_parse_cfg(), before
querying enumerated items or exposing the control to ALSA. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: bmg160: bail out when bandwidth/filter is not in table
bmg160_get_filter() walks bmg160_samp_freq_table[] looking for the entry
matching the bw_bits value read from the chip:
for (i = 0; i < ARRAY_SIZE(bmg160_samp_freq_table); ++i) {
if (bmg160_samp_freq_table[i].bw_bits == bw_bits)
break;
}
*val = bmg160_samp_freq_table[i].filter;
If no entry matches, i ends up equal to the array size and the next line
reads one slot past the end. bmg160_set_filter() has the same shape, driven
by 'val' instead of bw_bits.
smatch flags both:
drivers/iio/gyro/bmg160_core.c:204 bmg160_get_filter() error:
buffer overflow 'bmg160_samp_freq_table' 7 <= 7
drivers/iio/gyro/bmg160_core.c:222 bmg160_set_filter() error:
buffer overflow 'bmg160_samp_freq_table' 7 <= 7
Return -EINVAL when no entry matches.
The set_filter() path is reachable from userspace via the sysfs
in_anglvel_filter_low_pass_3db_frequency interface, so userspace can
trivially trigger the out-of-bounds read with a value that is not in
bmg160_samp_freq_table[].filter. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kxsd9: fix runtime PM imbalance on write_raw() error
kxsd9_write_raw() takes a runtime PM reference with pm_runtime_get_sync()
but returns -EINVAL directly when a scale with a non-zero integer part is
requested, skipping the matching pm_runtime_put_autosuspend(). This leaks
a runtime PM usage-counter reference on every such write, after which the
device can no longer autosuspend.
Set the error code and fall through to the existing put instead of
returning early. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: correct drop logic for malformed AMPDU frames
The previous commit aims to fix issue caused by malformed AMPDU frames.
But the drop logic fails to deal with the first AMPDU packet paired with
certain range of sequence number, and leads to unexpected packet drop.
It is more likely to encounter this failure when there are busy traffic
during rekey process and could lead to disconnection from the AP.
Fix this by adding a initial state judgement and only reset status
during pairwise rekey. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: CPPC: Suppress UBSAN warning caused by field misuse
The definition of reg->access_width changes depending on the
reg->space_id type. Type ACPI_ADR_SPACE_PLATFORM_COMM uses
access_width to indicate the PCC region, which can result in a UBSAN
if the value is greater than 4.
For example:
UBSAN: shift-out-of-bounds in drivers/acpi/cppc_acpi.c:1090:9
shift exponent 32 is too large for 32-bit type 'int'
CPU: 61 UID: 0 PID: 1220 Comm: (udev-worker) Not tainted 7.0.10-201.fc44.aarch64 #1 PREEMPT(lazy)
Hardware name: To be filled by O.E.M.
Call trace:
...(trimming)
ubsan_epilogue+0x10/0x48
__ubsan_handle_shift_out_of_bounds+0xdc/0x1e0
cpc_write+0x4d0/0x670
cppc_set_perf+0x18c/0x490
cppc_cpufreq_cpu_init+0x1c8/0x380 [cppc_cpufreq]
... (trimming)
Lets fix this by validating the region type, as well as whether
access_width has a value. Then since we are returning bit_width
directly for ACPI_ADR_SPACE_PLATFORM_COMM, drop the code correcting
the size. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_api: Handle TC_ACT_CONSUMED in tcf_qevent_handle
tcf_classify() can return TC_ACT_CONSUMED while the skb is held by the
defragmentation engine (e.g. act_ct on out-of-order fragments). When
that happens the skb is no longer owned by the caller and must not be
touched again.
tcf_qevent_handle() did not handle TC_ACT_CONSUMED: it fell through the
switch and returned the skb to the caller as if classification had
passed. The only qdisc that wires up qevents today is RED, via three call sites
(qe_mark on RED_PROB_MARK/HARD_MARK, qe_early_drop on congestion_drop)
red_enqueue() was continuing to operate on an skb it no longer owns in this
case -- enqueueing it, dropping it, or updating statistics. Resulting in a UAF.
tc qdisc add dev eth0 root handle 1: red ... qevent early_drop block 10
tc filter add block 10 ... action ct
(with ct defrag enabled and traffic that produces out-of-order
fragments, e.g. a fragmented UDP stream)
Handle TC_ACT_CONSUMED in tcf_qevent_handle() the same way the ingress
and egress fast paths do: treat it as stolen and return NULL without
touching the skb. Unlike the TC_ACT_STOLEN case, the skb must not be
dropped/freed here, as it is no longer owned by us. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - remove unused character device and IOCTLs
The QAT driver exposes a character device (qat_adf_ctl) with IOCTLs
for device configuration, start, stop, status query and enumeration.
These IOCTLs are not part of any public uAPI header and have no known
in-tree or out-of-tree users. Device lifecycle is already managed via
sysfs.
The ioctl interface also increases the attack surface and is the
subject of a number of bug reports.
Remove the character device, the IOCTL definitions, and the related
data structures (adf_dev_status_info, adf_user_cfg_key_val,
adf_user_cfg_section, adf_user_cfg_ctl_data). Drop the now-unused
adf_cfg_user.h header and strip adf_ctl_drv.c down to the minimal
module_init/module_exit hooks for workqueue, AER, and crypto/compression
algorithm registration.
Clean up leftover dead code that was only reachable from the removed
IOCTL paths: adf_cfg_del_all(), adf_devmgr_verify_id(),
adf_devmgr_get_num_dev(), adf_devmgr_get_dev_by_id(),
adf_get_vf_real_id() and the unused ADF_CFG macros.
Additionally, drop the entry associated to QAT IOCTLs in
ioctl-number.rst. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/hyperv: validate resolution_count and fix WIN8 fallback
A SYNTHVID_RESOLUTION_RESPONSE with resolution_count > 64 walks past
the supported_resolution[SYNTHVID_MAX_RESOLUTION_COUNT] array in the
parse loop. Bound resolution_count against the array size, folded
into the existing zero-check.
When the WIN10 resolution probe fails, the caller in
hyperv_connect_vsp() left hv->screen_*_max / preferred_* unpopulated,
which sets mode_config.max_width / max_height to 0 and makes
drm_internal_framebuffer_create() reject every userspace framebuffer
with -EINVAL. The pre-WIN10 branch had the same gap for
preferred_width / preferred_height. Use a single post-probe fallback
guarded by screen_width_max == 0 so both paths converge on the WIN8
defaults. |
| In the Linux kernel, the following vulnerability has been resolved:
net/handshake: Take a long-lived file reference at submit
handshake_nl_accept_doit() needs the file pointer backing
req->hr_sk->sk_socket to survive the window between
handshake_req_next() and the subsequent FD_PREPARE() and get_file().
The submit-side sock_hold() does not provide that. sk_refcnt keeps
struct sock alive, but struct socket is owned by sock->file: when
the consumer fputs the last file reference, sock_release() tears
the socket down regardless of any sock_hold.
Add an hr_file pointer to struct handshake_req and acquire an
explicit reference on sock->file during handshake_req_submit().
handshake_complete() and handshake_req_cancel() release the
reference on the completion-bit-winning path.
The submit error path must also release the file reference, but
after rhashtable insertion a concurrent handshake_req_cancel() can
discover the request and race the error path. Gate the error-path
cleanup -- sk_destruct restoration, fput, and request destruction
-- with test_and_set_bit(HANDSHAKE_F_REQ_COMPLETED), the same
serialization handshake_complete() and handshake_req_cancel()
already use. When cancel has already claimed ownership, the submit
error path returns without touching the request; socket teardown
handles final destruction.
The accept-side dereferences are not yet retargeted; that change
comes in the next patch. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix eswitch mode block underflow on IPsec acquire SA
mlx5e_xfrm_add_state() handles acquire-flow temporary SAs by allocating
software state and skipping hardware offload setup.
That path jumps to the common success label before taking the eswitch mode
block. After tunnel-mode validation was moved earlier, the common success
label unconditionally calls mlx5_eswitch_unblock_mode(). For acquire SAs,
this decrements esw->offloads.num_block_mode without a matching increment.
Return directly after installing the acquire SA offload handle, so only the
paths that successfully called mlx5_eswitch_block_mode() call the matching
unblock. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_ffa: Bound PARTITION_INFO_GET_REGS copies
The register-based PARTITION_INFO_GET path trusted the firmware-provided
indices when copying partition descriptors into the caller buffer.
Reject inconsistent counts or index progressions so the copy loop cannot
write past the allocated array.
(fixed cur_idx when exactly one descriptor in the first fragment) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vce1: Fix VCE 1 firmware size and offsets
The VCPU BO contains the actual FW at an offset, but
it was not calculated into the VCPU BO size.
Subtract this from the FW size to make sure there is
no out of bounds access.
Make sure the stack and data offsets are aligned to
the 32K TLB size.
Check that the FW microcode actually fits in the
space that is reserved for it.
(cherry picked from commit c16fe59f622a080fc457a57b3e8f14c780699449) |
