| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: tas2781: bound firmware description string parsing
The TAS2781 firmware parser reads several variable-length description
strings with strlen() before checking that the string terminator is
present inside the firmware blob. A malformed firmware image without a
NUL terminator can therefore make the parser walk past the end of the
firmware buffer before the later size checks run.
Add a small bounded string-length helper and use it for all description
fields that are parsed from the firmware buffer. Keep the existing size
checks for the fixed bytes that follow each string. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Fix IRQ unsafe locking in gdom allocation
Lockdep complains:
[ 259.410489] =====================================================
[ 259.417287] WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
[ 259.424667] 7.0.0-g51db1d8d2113 #54 Not tainted
[ 259.429718] -----------------------------------------------------
[ 259.436516] qemu-system-x86/10143 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 259.444670] ff3b2b1c60305170 (&xa->xa_lock#25){+.+.}-{3:3}, at: __domain_flush_pages+0x17c/0x4b0
[ 259.454485]
and this task is already holding:
[ 259.460991] ff3b2b1c98504cc0 (&domain->lock){-.-.}-{3:3}, at: amd_iommu_iotlb_sync+0x25/0x60
[ 259.470408] which would create a new lock dependency:
[ 259.476041] (&domain->lock){-.-.}-{3:3} -> (&xa->xa_lock#25){+.+.}-{3:3}
[ 259.483615]
but this new dependency connects a HARDIRQ-irq-safe lock:
[ 259.492447] (&domain->lock){-.-.}-{3:3}
[ 259.492449]
... which became HARDIRQ-irq-safe at:
[ 259.503705] lock_acquire+0xb6/0x2e0
[ 259.507790] _raw_spin_lock_irqsave+0x3e/0x60
[ 259.512748] amd_iommu_flush_iotlb_all+0x20/0x50
[ 259.517996] iommu_dma_free_iova.isra.0+0x1b8/0x1e0
[ 259.523534] __iommu_dma_unmap+0xc2/0x140
[ 259.528100] iommu_dma_unmap_phys+0x55/0xc0
[ 259.532863] dma_unmap_phys+0x274/0x2e0
[ 259.537238] dma_unmap_page_attrs+0x17/0x30
[ 259.542000] nvme_unmap_data+0x13e/0x280
[ 259.546473] nvme_pci_complete_batch+0x45/0x70
[ 259.551524] nvme_irq+0x83/0x90
[ 259.555123] __handle_irq_event_percpu+0x92/0x360
[ 259.560466] handle_irq_event+0x39/0x80
[ 259.564841] handle_edge_irq+0xb2/0x1a0
[ 259.569214] __common_interrupt+0x4e/0x130
[ 259.573882] common_interrupt+0x88/0xa0
[ 259.578256] asm_common_interrupt+0x27/0x40
[ 259.583019] cpuidle_enter_state+0x119/0x5d0
[ 259.587877] cpuidle_enter+0x2e/0x50
[ 259.591962] do_idle+0x153/0x2c0
[ 259.595657] cpu_startup_entry+0x29/0x30
[ 259.600128] start_secondary+0x118/0x150
[ 259.604601] common_startup_64+0x13e/0x141
[ 259.609266]
to a HARDIRQ-irq-unsafe lock:
[ 259.615384] (&xa->xa_lock#25){+.+.}-{3:3}
[ 259.615386]
... which became HARDIRQ-irq-unsafe at:
[ 259.627039] ...
[ 259.627039] lock_acquire+0xb6/0x2e0
[ 259.633071] _raw_spin_lock+0x2f/0x50
[ 259.637250] amd_iommu_alloc_domain_nested+0x140/0x3c0
[ 259.643078] iommufd_hwpt_alloc+0x272/0x800 [iommufd]
[ 259.648813] iommufd_fops_ioctl+0x14e/0x200 [iommufd]
[ 259.654547] __x64_sys_ioctl+0x9d/0xf0
...
Since amd_iommu_domain_flush_pages() necessarily holds domain->lock to do the
flush, switch the allocation side in gdom_info_load_or_alloc_locked() to
HARDIRQ-safe allocation. The IOMMU_DESTROY->free path has the same issue,
so switch that path to HARDIRQ-safe locking as well. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda: cs35l41: validate and free ACPI mute object
cs35l41_get_acpi_mute_state() evaluates a _DSM method to get the ACPI
mute state and reads the first byte from the returned object.
However, the returned ACPI object is owned by the caller and is never
freed after use, so each successful query leaks the _DSM result object.
The code also assumes that the returned object is a buffer with at least
one byte. A malformed firmware response can return a different object
type or an empty buffer, and the direct ret->buffer.pointer dereference
can then access an invalid pointer.
Use the typed _DSM helper, validate that the returned buffer contains at
least one byte, and free the ACPI object after reading it. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: validate Realtek vendor event length
btusb_recv_event_realtek() reads the event code at data[0] and the Realtek
subevent code at data[2] before deciding whether to consume a vendor event
as a coredump.
For example, the two-byte event ff 00 contains a complete vendor-event
header declaring zero parameters. The old classifier still reads a
nonexistent third byte and can misclassify the event as a coredump if the
adjacent byte is 0x34.
Require the HCI event header and first parameter to be present before
inspecting the Realtek subevent code. Short events continue through the
normal HCI receive path, which owns their protocol validation. |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: fix devconf_all NULL dereference when IPv6 is disabled
When booting with the 'ipv6.disable=1' parameter, the devconf_all is
never initialized because inet6_init() exits before addrconf_init() is
called which initializes it. bond_send_validate(), however, will still
call bond_ns_send_all() even ipv6 is indeed disabled. It will lead to
NULL derefence of net->ipv6.devconf_all in ip6_pol_route().
BUG: kernel NULL pointer dereference, address: 000000000000000c
[...]
Workqueue: bond0 bond_arp_monitor [bonding]
RIP: 0010:ip6_pol_route+0x69/0x480
[...]
Call Trace:
<TASK>
? srso_return_thunk+0x5/0x5f
? __pfx_ip6_pol_route_output+0x10/0x10
fib6_rule_lookup+0xfe/0x260
? wakeup_preempt+0x8a/0x90
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
? sched_balance_rq+0x369/0x810
ip6_route_output_flags+0xd7/0x170
bond_ns_send_all+0xde/0x280 [bonding]
bond_ab_arp_probe+0x296/0x320 [bonding]
? srso_return_thunk+0x5/0x5f
bond_activebackup_arp_mon+0xb4/0x2c0 [bonding]
process_one_work+0x196/0x370
worker_thread+0x1af/0x320
? srso_return_thunk+0x5/0x5f
? __pfx_worker_thread+0x10/0x10
kthread+0xe3/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x199/0x260
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Fix this by adding ipv6_mod_enabled() condition check in the caller. |
| Hono is a Web application framework that provides support for any JavaScript runtime. From 4.7.0 to 4.12.33, the Proxy Helper proxy() function in hono/proxy does not remove response headers named by the origin's Connection header. Per RFC 9110 Section 7.6.1, an intermediary must remove the header fields listed in a message's Connection header field before forwarding the message, in addition to the well known hop by hop headers, but the proxy() function only removed the well known hop by hop headers, including Connection itself, from origin responses. A client may therefore receive response headers that the origin intended only for its immediate peer, disclosing connection scoped or internal metadata contained in such headers, when an application proxies responses from an origin that declares additional, non standard headers as hop by hop via the Connection response header. This issue is fixed in version 4.12.34. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: drop incoming messages that cross network namespace boundaries
rds_find_bound() looks up the destination socket using a global
rhashtable keyed solely on (addr, port, scope_id). Network namespaces
are not part of the key, so a sender in netns A can deliver an incoming
message (inc) to a socket that lives in a different netns B.
When this happens, inc->i_conn points to an rds_connection whose c_net
is netns A, but the receiving rs lives in netns B. Once the child
process that created netns A exits, cleanup_net() calls
rds_loop_exit_net() -> rds_loop_kill_conns() -> rds_conn_destroy(),
freeing that connection. If the survivor socket in netns B still holds
the inc, any subsequent dereference of inc->i_conn is a use-after-free.
There are two dangerous sites in rds_clear_recv_queue():
1. inc->i_conn->c_lcong (offset 88 of freed rds_connection, size 200)
read via rds_recv_rcvbuf_delta() -- confirmed by KASAN.
2. inc->i_conn->c_trans->inc_free(inc) (function pointer at offset 80)
called via rds_inc_put() when the inc refcount reaches zero -- same
race window, potential call-through-freed-object primitive.
The bug is reachable from unprivileged user namespaces
(CLONE_NEWUSER + CLONE_NEWNET), available since Linux 3.8.
Fix this by rejecting the delivery in rds_recv_incoming() when the
socket returned by rds_find_bound() belongs to a different network
namespace than the connection that carried the message. Use the
existing rds_conn_net() / sock_net() helpers and net_eq() for the
comparison. |
| In the Linux kernel, the following vulnerability has been resolved:
dpaa2-switch: put MAC endpoint device on disconnect
fsl_mc_get_endpoint() returns the MAC endpoint device with a reference
taken through device_find_child(). The switch port connect path stores
that device in mac->mc_dev and keeps it for the lifetime of the connected
MAC object.
However, the disconnect path only closes the MAC and frees the dpaa2_mac
object. It does not drop the endpoint device reference stored in
mac->mc_dev, so every successful connect leaks that device reference when
the MAC is later disconnected.
Drop the endpoint device reference before freeing the dpaa2_mac object. |
| In the Linux kernel, the following vulnerability has been resolved:
net: airoha: Fix potential use-after-free in airoha_ppe_deinit()
airoha_ppe_deinit() replaces the NPU pointer with NULL via
rcu_replace_pointer() but does not wait for existing RCU readers
to exit before calling ppe_deinit() and airoha_npu_put(). This can
cause a use-after-free if a reader in an RCU read-side critical
section still holds a reference to the NPU when it is freed.
The init path (airoha_ppe_init) already calls synchronize_rcu()
after rcu_assign_pointer(), but the deinit path introduced in
commit 6abcf751bc08 ("net: airoha: Fix schedule while atomic in
airoha_ppe_deinit()") omitted the matching barrier when switching
from rcu_read_lock()/rcu_dereference() to rcu_replace_pointer().
Add synchronize_rcu() before ppe_deinit() to ensure all existing
RCU readers have completed before the NPU resources are released. |
| In the Linux kernel, the following vulnerability has been resolved:
dpaa2-eth: put MAC endpoint device on disconnect
fsl_mc_get_endpoint() returns the MAC endpoint device with a reference
taken through device_find_child(). The Ethernet connect path stores that
device in mac->mc_dev and keeps it for the lifetime of the connected MAC
object.
However, the disconnect path only disconnects and closes the MAC before
freeing the dpaa2_mac object. It does not drop the endpoint device
reference stored in mac->mc_dev, so every successful connect leaks that
device reference when the MAC is later disconnected.
Drop the endpoint device reference after closing the MAC and before
freeing the dpaa2_mac object. |
| In the Linux kernel, the following vulnerability has been resolved:
nfp: Check resource mutex allocation
nfp_cpp_resource_find() allocates a CPP mutex handle for the matching
resource-table entry and then reports success. nfp_resource_try_acquire()
immediately passes that handle to nfp_cpp_mutex_trylock().
However, nfp_cpp_mutex_alloc() returns NULL on failure. If that happens
for a matching table entry, the resource lookup still returns success and
the following trylock dereferences a NULL mutex pointer while opening the
resource.
nfp_resource_acquire() already treats failure to allocate the table mutex
as -ENOMEM. Do the same for the resource mutex and fail the lookup before
publishing the rest of the resource handle.
This issue was found by a static analysis checker and confirmed by
manual source review. |
| In the Linux kernel, the following vulnerability has been resolved:
wan: wanxl: Only reset hardware after BAR mapping
wanxl_pci_init_one() stores the freshly allocated card in driver data
before the PLX BAR is mapped. Several early probe failures then unwind
through wanxl_pci_remove_one(), including failure to allocate the coherent
status area or to restore the DMA mask.
wanxl_pci_remove_one() unconditionally calls wanxl_reset(), and
wanxl_reset() dereferences card->plx. On those early failures card->plx
is still NULL, so the error path can dereference a NULL MMIO pointer.
Only issue the hardware reset once the BAR mapping exists. The remaining
cleanup in wanxl_pci_remove_one() already checks whether later resources
were allocated.
This issue was found by a static analysis checker and confirmed by
manual source review. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: bound uAP association event IEs to the event buffer
mwifiex_process_uap_event() handles EVENT_UAP_STA_ASSOC by exposing the
(re)association request IEs that the firmware copies into the event:
sinfo->assoc_req_ies = &event->data[len];
len = (u8 *)sinfo->assoc_req_ies - (u8 *)&event->frame_control;
sinfo->assoc_req_ies_len = le16_to_cpu(event->len) - (u16)len;
event->len is supplied by the device firmware and is never validated,
and the subtraction is unchecked. assoc_req_ies points into
adapter->event_body[MAX_EVENT_SIZE], a fixed-size array embedded in the
kmalloc()'d struct mwifiex_adapter.
On the ap_11n_enabled path mwifiex_set_sta_ht_cap() walks these IEs with
cfg80211_find_ie(), whose for_each_element() loop dereferences each
element header. A firmware-reported event->len larger than the bytes
actually received makes assoc_req_ies_len describe IEs that extend past
event_body, so the walk reads out of the adapter slab object, a
slab-out-of-bounds read (KASAN: slab-out-of-bounds in cfg80211_find_ie).
An event->len smaller than the header instead makes the int subtraction
negative, which wraps to a huge size_t when stored in assoc_req_ies_len.
The same length is handed to cfg80211_new_sta(), so a more modest
over-claim can also copy stale event_body bytes into the
NL80211_CMD_NEW_STATION notification.
A malicious or malfunctioning mwifiex device (USB/SDIO/PCIe) can deliver
such an event while the interface is in AP/uAP mode.
Validate event->len before use: reject a length that underflows the
header or that would place the IEs outside the event_body[] buffer the
event was copied into. event->len here is struct mwifiex_assoc_event.len,
a payload field internal to this event, not the transport frame length,
so it is validated in this handler rather than at the generic
MWIFIEX_TYPE_EVENT receive path, which only sees the event cause and the
transport frame length. The bound is against event_body[MAX_EVENT_SIZE]
rather than the actually-received length because the transports store the
event differently (USB and SDIO leave the 4-byte event header in
event_skb, PCIe strips it via skb_pull), whereas event_body is the single
fixed buffer all of them copy the event into. This is the event-path
analogue of the receive-path bounds checks added in commit 119585281617
("wifi: mwifiex: Fix OOB and integer underflow when rx packets"). |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Bound the early ACPI HID map
The ivrs_acpihid command-line parser appends entries to a fixed
four-element early_acpihid_map array. Unlike the sibling IOAPIC and HPET
parsers, it does not reject a fifth entry before incrementing the map size.
Check the capacity at the common found label before parsing the HID and
UID or writing the entry. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: serialize udp bearer replicast list updates
tipc_udp_rcast_add() and cleanup_bearer() both update ub->rcast.list with
list_add_rcu() / list_del_rcu(), but nothing serializes them. The add runs
from the encap receive softirq (via tipc_udp_rcast_disc()) without
rtnl_lock(), so it can race the cleanup delete and corrupt the list:
list_del corruption. prev->next should be ffff8880298d7ab8,
but was ffff88802449ad38. (prev=ffff888027e3ec98)
kernel BUG at lib/list_debug.c:62!
RIP: __list_del_entry_valid_or_report+0x17a/0x200
Workqueue: events cleanup_bearer
Call Trace:
cleanup_bearer (net/tipc/udp_media.c:811)
process_one_work (kernel/workqueue.c:3302)
worker_thread (kernel/workqueue.c:3466)
The bearer can be enabled from an unprivileged user namespace, as the
TIPCv2 generic-netlink ops carry no GENL_ADMIN_PERM.
Add a spinlock to struct udp_bearer and take it around the list_add_rcu()
in tipc_udp_rcast_add() and the list_del_rcu() loop in cleanup_bearer() so
the two writers can no longer corrupt the list.
Reject a duplicate peer under the same lock before allocating, and remove
tipc_udp_is_known_peer(). The old lockless pre-check in
tipc_udp_rcast_disc() was racy: two softirqs discovering the same peer
could both find it absent and add it twice.
cleanup_bearer() runs from a workqueue after tipc_udp_disable() clears the
bearer's up bit, so an encap softirq can still reach tipc_udp_rcast_add()
and add a peer after cleanup_bearer() has already emptied the list, leaking
that entry when the bearer is freed. Mark the bearer disabled under
rcast_lock once the list is emptied and refuse further additions. |
| In the Linux kernel, the following vulnerability has been resolved:
net: txgbe: fix FDIR filter leak on remove
Perfect FDIR filters can be added while the interface is down and are
kept on the software list for later restore. unregister_netdev() only
calls ndo_stop when the device is up, so txgbe_fdir_filter_exit() in
txgbe_close() is skipped in that case and the filters are leaked on
driver remove. Free the filter list from txgbe_remove() as well. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix auth_chunk_list capacity check in sctp_auth_ep_add_chunkid
sctp_auth_ep_add_chunkid() uses SCTP_NUM_CHUNK_TYPES (20) as the
capacity limit for ep->auth_chunk_list, allowing it to hold up to
20 chunk entries (param_hdr.length up to 24). However, the copy
destination asoc->c.auth_chunks in struct sctp_cookie is only
SCTP_AUTH_MAX_CHUNKS (16) entries (20 bytes). When more than 16
chunks are added, sctp_association_init() memcpy overflows the
destination by up to 4 bytes.
Fix by using SCTP_AUTH_MAX_CHUNKS as the capacity limit, matching
the destination capacity. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix auxiliary device add/del races
Two paths add or delete the same slot (pf->vfs[vf_id].padev): a VF's
pdsc_reset_done() and the PF's devlink enable_vnet/disable_vnet handler.
They serialize on config_lock, but neither guards the slot under it
correctly.
add() registers and stores a new auxiliary device without first checking
the slot, so a second add of an already-populated slot leaks the first
device. del() makes that check outside config_lock, so two concurrent
dels can both pass it; the first clears the slot, and the second
dereferences a NULL pointer.
Check and update the slot under config_lock in both paths. |
| In the Linux kernel, the following vulnerability has been resolved:
accel: ethosu: Fix element size accounting for cmd stream validation
There are 2 issues with the element size handling in the command stream
validation which result in too small of a size calculated when the
element size is 16/32/64 bits.
For NHWC format, the element size is simply missing from the
calculation.
The bitfield for the element size is different between IFM/IFM2 and
OFM. IFM and IFM2 encode the precision in parameter bits 2:3, while OFM
uses bits 1:2. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate stream count in sctp_process_strreset_inreq()
When processing a RESET_IN_REQUEST from a peer,
sctp_process_strreset_inreq() derives the stream count from the
parameter length but does not check whether the resulting
RESET_OUT_REQUEST would exceed SCTP_MAX_CHUNK_LEN.
The OUT request header (sctp_strreset_outreq, 16 bytes) is 8 bytes
larger than the IN request header (sctp_strreset_inreq, 8 bytes).
Generally, the IP payload is bounded to 65535 bytes, so the stream
list cannot be large enough to trigger the overflow. However, on
interfaces with MTU > 65535 (e.g., loopback with IPv6 jumbograms), a
stream list that fits within the incoming IN parameter can cause a
__u16 overflow in sctp_make_strreset_req() when computing the OUT
request size, leading to an undersized skb allocation and a kernel
BUG:
net/core/skbuff.c:207 skb_panic
net/core/skbuff.c:2625 skb_put
net/sctp/sm_make_chunk.c:1535 sctp_addto_chunk
net/sctp/sm_make_chunk.c:3695 sctp_make_strreset_req
net/sctp/stream.c:655 sctp_process_strreset_inreq
The local setsockopt path validates the generated reset request size.
However, for an incoming-only reset, it accounts for the smaller IN
request even though the peer must generate an OUT request with the same
stream list. Such a request cannot be completed successfully by the
peer.
Reject peer IN requests whose corresponding OUT request would exceed
SCTP_MAX_CHUNK_LEN. Also tighten the local check so it does not send an
IN request that would require an oversized OUT request from the peer. |
