| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: ocelot: fix system hang on level based interrupts
The current implementation only calls chained_irq_enter() and
chained_irq_exit() if it detects pending interrupts.
```
for (i = 0; i < info->stride; i++) {
uregmap_read(info->map, id_reg + 4 * i, ®);
if (!reg)
continue;
chained_irq_enter(parent_chip, desc);
```
However, in case of GPIO pin configured in level mode and the parent
controller configured in edge mode, GPIO interrupt might be lowered by the
hardware. In the result, if the interrupt is short enough, the parent
interrupt is still pending while the GPIO interrupt is cleared;
chained_irq_enter() never gets called and the system hangs trying to
service the parent interrupt.
Moving chained_irq_enter() and chained_irq_exit() outside the for loop
ensures that they are called even when GPIO interrupt is lowered by the
hardware.
The similar code with chained_irq_enter() / chained_irq_exit() functions
wrapping interrupt checking loop may be found in many other drivers:
```
grep -r -A 10 chained_irq_enter drivers/pinctrl
``` |
| In the Linux kernel, the following vulnerability has been resolved:
posix-clock: Fix missing timespec64 check in pc_clock_settime()
As Andrew pointed out, it will make sense that the PTP core
checked timespec64 struct's tv_sec and tv_nsec range before calling
ptp->info->settime64().
As the man manual of clock_settime() said, if tp.tv_sec is negative or
tp.tv_nsec is outside the range [0..999,999,999], it should return EINVAL,
which include dynamic clocks which handles PTP clock, and the condition is
consistent with timespec64_valid(). As Thomas suggested, timespec64_valid()
only check the timespec is valid, but not ensure that the time is
in a valid range, so check it ahead using timespec64_valid_strict()
in pc_clock_settime() and return -EINVAL if not valid.
There are some drivers that use tp->tv_sec and tp->tv_nsec directly to
write registers without validity checks and assume that the higher layer
has checked it, which is dangerous and will benefit from this, such as
hclge_ptp_settime(), igb_ptp_settime_i210(), _rcar_gen4_ptp_settime(),
and some drivers can remove the checks of itself. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_pmem: Check device status before requesting flush
If a pmem device is in a bad status, the driver side could wait for
host ack forever in virtio_pmem_flush(), causing the system to hang.
So add a status check in the beginning of virtio_pmem_flush() to return
early if the device is not activated. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: k3-r5: Fix error handling when power-up failed
By simply bailing out, the driver was violating its rule and internal
assumptions that either both or no rproc should be initialized. E.g.,
this could cause the first core to be available but not the second one,
leading to crashes on its shutdown later on while trying to dereference
that second instance. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau/dmem: Fix vulnerability in migrate_to_ram upon copy error
The `nouveau_dmem_copy_one` function ensures that the copy push command is
sent to the device firmware but does not track whether it was executed
successfully.
In the case of a copy error (e.g., firmware or hardware failure), the
copy push command will be sent via the firmware channel, and
`nouveau_dmem_copy_one` will likely report success, leading to the
`migrate_to_ram` function returning a dirty HIGH_USER page to the user.
This can result in a security vulnerability, as a HIGH_USER page that may
contain sensitive or corrupted data could be returned to the user.
To prevent this vulnerability, we allocate a zero page. Thus, in case of
an error, a non-dirty (zero) page will be returned to the user. |
| In the Linux kernel, the following vulnerability has been resolved:
static_call: Handle module init failure correctly in static_call_del_module()
Module insertion invokes static_call_add_module() to initialize the static
calls in a module. static_call_add_module() invokes __static_call_init(),
which allocates a struct static_call_mod to either encapsulate the built-in
static call sites of the associated key into it so further modules can be
added or to append the module to the module chain.
If that allocation fails the function returns with an error code and the
module core invokes static_call_del_module() to clean up eventually added
static_call_mod entries.
This works correctly, when all keys used by the module were converted over
to a module chain before the failure. If not then static_call_del_module()
causes a #GP as it blindly assumes that key::mods points to a valid struct
static_call_mod.
The problem is that key::mods is not a individual struct member of struct
static_call_key, it's part of a union to save space:
union {
/* bit 0: 0 = mods, 1 = sites */
unsigned long type;
struct static_call_mod *mods;
struct static_call_site *sites;
};
key::sites is a pointer to the list of built-in usage sites of the static
call. The type of the pointer is differentiated by bit 0. A mods pointer
has the bit clear, the sites pointer has the bit set.
As static_call_del_module() blidly assumes that the pointer is a valid
static_call_mod type, it fails to check for this failure case and
dereferences the pointer to the list of built-in call sites, which is
obviously bogus.
Cure it by checking whether the key has a sites or a mods pointer.
If it's a sites pointer then the key is not to be touched. As the sites are
walked in the same order as in __static_call_init() the site walk can be
terminated because all subsequent sites have not been touched by the init
code due to the error exit.
If it was converted before the allocation fail, then the inner loop which
searches for a module match will find nothing.
A fail in the second allocation in __static_call_init() is harmless and
does not require special treatment. The first allocation succeeded and
converted the key to a module chain. That first entry has mod::mod == NULL
and mod::next == NULL, so the inner loop of static_call_del_module() will
neither find a module match nor a module chain. The next site in the walk
was either already converted, but can't match the module, or it will exit
the outer loop because it has a static_call_site pointer and not a
static_call_mod pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix error path in multi-packet WQE transmit
Remove the erroneous unmap in case no DMA mapping was established
The multi-packet WQE transmit code attempts to obtain a DMA mapping for
the skb. This could fail, e.g. under memory pressure, when the IOMMU
driver just can't allocate more memory for page tables. While the code
tries to handle this in the path below the err_unmap label it erroneously
unmaps one entry from the sq's FIFO list of active mappings. Since the
current map attempt failed this unmap is removing some random DMA mapping
that might still be required. If the PCI function now presents that IOVA,
the IOMMU may assumes a rogue DMA access and e.g. on s390 puts the PCI
function in error state.
The erroneous behavior was seen in a stress-test environment that created
memory pressure. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: don't use rate mask for offchannel TX either
Like the commit ab9177d83c04 ("wifi: mac80211: don't use rate mask for
scanning"), ignore incorrect settings to avoid no supported rate warning
reported by syzbot.
The syzbot did bisect and found cause is commit 9df66d5b9f45 ("cfg80211:
fix default HE tx bitrate mask in 2G band"), which however corrects
bitmask of HE MCS and recognizes correctly settings of empty legacy rate
plus HE MCS rate instead of returning -EINVAL.
As suggestions [1], follow the change of SCAN TX to consider this case of
offchannel TX as well.
[1] https://lore.kernel.org/linux-wireless/6ab2dc9c3afe753ca6fdcdd1421e7a1f47e87b84.camel@sipsolutions.net/T/#m2ac2a6d2be06a37c9c47a3d8a44b4f647ed4f024 |
| In the Linux kernel, the following vulnerability has been resolved:
x86/tdx: Fix "in-kernel MMIO" check
TDX only supports kernel-initiated MMIO operations. The handle_mmio()
function checks if the #VE exception occurred in the kernel and rejects
the operation if it did not.
However, userspace can deceive the kernel into performing MMIO on its
behalf. For example, if userspace can point a syscall to an MMIO address,
syscall does get_user() or put_user() on it, triggering MMIO #VE. The
kernel will treat the #VE as in-kernel MMIO.
Ensure that the target MMIO address is within the kernel before decoding
instruction. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: don't wait for tx queues if firmware is dead
There is a WARNING in iwl_trans_wait_tx_queues_empty() (that was
recently converted from just a message), that can be hit if we
wait for TX queues to become empty after firmware died. Clearly,
we can't expect anything from the firmware after it's declared dead.
Don't call iwl_trans_wait_tx_queues_empty() in this case. While it could
be a good idea to stop the flow earlier, the flush functions do some
maintenance work that is not related to the firmware, so keep that part
of the code running even when the firmware is not running.
[edit commit message] |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Limit the period on Haswell
Running the ltp test cve-2015-3290 concurrently reports the following
warnings.
perfevents: irq loop stuck!
WARNING: CPU: 31 PID: 32438 at arch/x86/events/intel/core.c:3174
intel_pmu_handle_irq+0x285/0x370
Call Trace:
<NMI>
? __warn+0xa4/0x220
? intel_pmu_handle_irq+0x285/0x370
? __report_bug+0x123/0x130
? intel_pmu_handle_irq+0x285/0x370
? __report_bug+0x123/0x130
? intel_pmu_handle_irq+0x285/0x370
? report_bug+0x3e/0xa0
? handle_bug+0x3c/0x70
? exc_invalid_op+0x18/0x50
? asm_exc_invalid_op+0x1a/0x20
? irq_work_claim+0x1e/0x40
? intel_pmu_handle_irq+0x285/0x370
perf_event_nmi_handler+0x3d/0x60
nmi_handle+0x104/0x330
Thanks to Thomas Gleixner's analysis, the issue is caused by the low
initial period (1) of the frequency estimation algorithm, which triggers
the defects of the HW, specifically erratum HSW11 and HSW143. (For the
details, please refer https://lore.kernel.org/lkml/87plq9l5d2.ffs@tglx/)
The HSW11 requires a period larger than 100 for the INST_RETIRED.ALL
event, but the initial period in the freq mode is 1. The erratum is the
same as the BDM11, which has been supported in the kernel. A minimum
period of 128 is enforced as well on HSW.
HSW143 is regarding that the fixed counter 1 may overcount 32 with the
Hyper-Threading is enabled. However, based on the test, the hardware
has more issues than it tells. Besides the fixed counter 1, the message
'interrupt took too long' can be observed on any counter which was armed
with a period < 32 and two events expired in the same NMI. A minimum
period of 32 is enforced for the rest of the events.
The recommended workaround code of the HSW143 is not implemented.
Because it only addresses the issue for the fixed counter. It brings
extra overhead through extra MSR writing. No related overcounting issue
has been reported so far. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mtrr: Check if fixed MTRRs exist before saving them
MTRRs have an obsolete fixed variant for fine grained caching control
of the 640K-1MB region that uses separate MSRs. This fixed variant has
a separate capability bit in the MTRR capability MSR.
So far all x86 CPUs which support MTRR have this separate bit set, so it
went unnoticed that mtrr_save_state() does not check the capability bit
before accessing the fixed MTRR MSRs.
Though on a CPU that does not support the fixed MTRR capability this
results in a #GP. The #GP itself is harmless because the RDMSR fault is
handled gracefully, but results in a WARN_ON().
Add the missing capability check to prevent this. |
| The issue was addressed with improved checks. This issue is fixed in iOS 18.1 and iPadOS 18.1. An attacker may be able to view restricted content from the lock screen. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: Return non-zero value from tipc_udp_addr2str() on error
tipc_udp_addr2str() should return non-zero value if the UDP media
address is invalid. Otherwise, a buffer overflow access can occur in
tipc_media_addr_printf(). Fix this by returning 1 on an invalid UDP
media address. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mv88e6xxx: Correct check for empty list
Since commit a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: check validation of fault attrs in f2fs_build_fault_attr()
- It missed to check validation of fault attrs in parse_options(),
let's fix to add check condition in f2fs_build_fault_attr().
- Use f2fs_build_fault_attr() in __sbi_store() to clean up code. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpi3mr: Sanitise num_phys
Information is stored in mr_sas_port->phy_mask, values larger then size of
this field shouldn't be allowed. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp_metrics: validate source addr length
I don't see anything checking that TCP_METRICS_ATTR_SADDR_IPV4
is at least 4 bytes long, and the policy doesn't have an entry
for this attribute at all (neither does it for IPv6 but v6 is
manually validated). |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: Octeon: Add PCIe link status check
The standard PCIe configuration read-write interface is used to
access the configuration space of the peripheral PCIe devices
of the mips processor after the PCIe link surprise down, it can
generate kernel panic caused by "Data bus error". So it is
necessary to add PCIe link status check for system protection.
When the PCIe link is down or in training, assigning a value
of 0 to the configuration address can prevent read-write behavior
to the configuration space of peripheral PCIe devices, thereby
preventing kernel panic. |
| In the Linux kernel, the following vulnerability has been resolved:
mips: bmips: BCM6358: make sure CBR is correctly set
It was discovered that some device have CBR address set to 0 causing
kernel panic when arch_sync_dma_for_cpu_all is called.
This was notice in situation where the system is booted from TP1 and
BMIPS_GET_CBR() returns 0 instead of a valid address and
!!(read_c0_brcm_cmt_local() & (1 << 31)); not failing.
The current check whether RAC flush should be disabled or not are not
enough hence lets check if CBR is a valid address or not. |
