| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
watchdog: unregister PM notifier on watchdog unregister
watchdog_register_device() registers wdd->pm_nb when
WDOG_NO_PING_ON_SUSPEND is set, but watchdog_unregister_device() does not
remove it. This leaves an embedded notifier block on the PM notifier chain
after the watchdog device has been unregistered.
A later suspend/resume notification can then call watchdog_pm_notifier()
with a stale watchdog_device pointer, or at minimum after wdd->wd_data has
been cleared by watchdog_dev_unregister().
Unregister the PM notifier before tearing down the watchdog device. |
| In the Linux kernel, the following vulnerability has been resolved:
of: reserved_mem: avoid post-init UAF when alloc_reserved_mem_array() fails
The global pointer 'reserved_mem' continues to reference the
reserved_mem_array which lives in __initdata if
alloc_reserved_mem_array() fails. of_reserved_mem_lookup() is
exported for post-init use, that would dereference freed memory
and trigger a use-after-free.
So reset reserved_mem_count to 0 when alloc_reserved_mem_array()
fails. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Fix endpoint/socket association handling
Disassociating a socket from an endpoint via siw_socket_disassoc() may
release the last reference on that endpoint and free it. Therefore, don't
clear the endpoints socket pointer after calling that function, but
within.
This fixes a:
BUG: KASAN: slab-use-after-free in siw_cm_work_handler (drivers/infiniband/sw/siw/siw_cm.c:1053 drivers/infiniband/sw/siw/siw_cm.c:1075)
which occurred after processing a malformed MPA request during connection
establishment, causing the new endpoint to be closed. |
| In the Linux kernel, the following vulnerability has been resolved:
configfs_lookup(): don't leave ->s_dentry dangling on failure
Normally ->s_dentry is cleared when dentry it's pointing to becomes
negative (on eviction, realistically). However, that only happens
if dentry gets to be positive in the first place; in case of inode
allocation failure dentry never becomes positive, so ->d_iput()
is not called at all.
We do part of what normally would've been done by configfs_d_iput()
(dropping the reference to configfs_dirent) manually, but we do
not clear ->s_dentry there. Sloppy as it is, it does not matter in
case of configfs_create_{dir,link}() - there configfs_dirent does
not survive dropping the sole reference to it.
However, for configfs_lookup() it *does* survive, with a dangling
pointer to soon to be freed dentry sitting it its ->s_dentry.
Subsequent getdents(2) in that directory will end up dereferencing
that pointer in order to pick the inode number. Use after free...
This is the minimal fix; the right approach is to set the linkage
between dentry and configfs_dirent only after we know that we have
an inode, but that takes more surgery and the bug had been there
since 2006, so... |
| In the Linux kernel, the following vulnerability has been resolved:
dlm: fix add msg handle in send_queue ordered
In a benchmark scenario triggering a lot of requests that triggers a lot
of DLM messages on the network it can be that the mh->seq is not ordered
according the oldest seq number. This ordering is required by
dlm_receive_ack as "before(mh->seq, seq)" will stop to check for older
sequence numbers that are ordered in the tail of "node->send_queue".
The side effects of not having it correct ordered regarding
"before(mh->seq, seq)" are refcounting issues and use-after free.
I only was able to reproduce this issue in a experimental DLM branch
and a user space DLM benchmark that uses io_uring. After changing this I
don't experienced any refcounting with the sending buffer issues anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: stop fast-leave after deleting a port group
br_multicast_leave_group() iterates mp->ports with pp = &p->next in
its fast-leave path. After br_multicast_del_pg() removes p,
continuing the loop advances pp through the deleted entry.
If multicast-to-unicast was enabled, the bridge can hold multiple port
groups for the same port and group with different source MAC
addresses. Once multicast-to-unicast is disabled,
br_port_group_equal() matches those entries by port only. A fast leave
can then delete one entry and continue from its stale next pointer,
leaving mp->ports pointing at a deleted port group.
Fast leave only needs to remove one matching port group. Break after
br_multicast_del_pg() so the loop stops before dereferencing the
removed entry. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/page_reporting: use system_freezable_wq to fix UAF during suspend
During PM freeze (e.g. S3 suspend or S4 hibernation), device drivers like
virtio_balloon reset their underlying virtio devices and delete their
virtqueues via vdev->config->del_vqs().
However, page reporting work (page_reporting_process) was scheduled on the
global system_wq. Because system_wq lacks the WQ_FREEZABLE flag, the PM
freezer skips it, leaving page_reporting_process active during suspend.
If pages are freed into the buddy allocator while suspending (for example,
when core MM invokes the balloon shrinker during S4 hibernation image
saving), page reporting triggers virtballoon_free_page_report() on deleted
virtqueues, resulting in a Use-After-Free / General Protection Fault:
[ 196.795226] general protection fault, probably for non-canonical address 0xaa1436fe70dae6df: 0000 [#1] SMP NOPTI
[ 196.825967] Workqueue: events page_reporting_process
[ 196.831038] RIP: 0010:virtqueue_add_split+0x233/0x4c0 [virtio_ring]
[ 196.927073] virtballoon_free_page_report+0x3a/0xe0 [virtio_balloon]
[ 196.946943] page_reporting_process+0x370/0x4f0
Fix this by switching page reporting work to system_freezable_wq. This
ensures that the PM freezer pauses page_reporting_process before device
drivers destroy their reporting virtqueues. Because the reporting worker
is frozen, memory reclamation/freeing (e.g. via shrinker execution) can
safely return pages to MM during freeze without triggering unfrozen
reporting work on deleted virtqueues.
This aligns with the driver's existing design. The comment in
virtballoon_freeze() states:
/*
* The workqueue is already frozen by the PM core before this
* function is called.
*/
Testing:
I have verified these fixes using Google’s virtualization infrastructure
by running continuous suspend/resume iterations (40+ cycles) while
churning memory using stress-ng (`stress-ng --vm 4 --vm-bytes 60%
--timeout 1`) to constantly create free pages for the buddy allocator. We
also set the `page_reporting_order` parameter to 0 to make the page
reporting worker highly sensitive, forcing it to pick up any 4K free
pages. This confirmed that the UAF crashes are no longer reproducible. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: avoid use-after-free in poll trace queue dumps
TIPC socket tracepoints dump queue state through tipc_sk_dump(). Most
queue-dump callsites already serialize that walk under the socket lock or
sk->sk_lock.slock, but tipc_poll() calls trace_tipc_sk_poll(...,
TIPC_DUMP_ALL, ...) without holding either lock.
That lets the poll trace path reach tipc_list_dump() and backlog head/tail
dumping while another context dequeues and frees an skb, leaving the trace
helper dereferencing a stale queue entry.
Stop the unlocked poll trace site from requesting queue dumps. Other queue
dump trace callsites keep their existing output under the locking they
already provide, while poll still emits the event itself without walking
live queue members from an unlocked context. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: do not update comments from kernel-side hash adds
mtype_resize() copies comment pointers with memcpy(), not the comment
objects themselves. During the window after an entry has been copied but
before the table swap and backlog replay, the old table is still
published for packet-side updates while the replacement-table entry
already holds the same ip_set_comment_rcu pointer.
If xt_SET --add-set ... --exist hits that old entry in this window,
mtype_add() calls ip_set_init_comment() even though packet-side adds
carry no comment payload. That call frees the shared comment through the
old entry, so the replacement-table entry now holds a stale pointer.
When the queued add is replayed on the new table, mtype_add() calls
ip_set_init_comment() again and strlen() dereferences the stale pointer.
Fix this in mtype_add() by skipping ip_set_init_comment() when
ext->target marks a packet-side add. Userspace adds still update
comments, while packet-side adds can no longer free comment storage
shared with a resize copy. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: 6fire: Fix UAF at error handling during probe
Although 6fire driver had a few fixes for dealing with the early error
handling during the probe phase, it forgot a pending URB before
freeing the resources, which may lead to a UAF.
This patch addresses it by doing the almost same cleanup procedure
like the normal disconnect phase at the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
dibs: fix use-after-free of dmb_node in loopback attach/detach/unregister
dibs_lo_attach_dmb(), dibs_lo_detach_dmb() and dibs_lo_unregister_dmb()
look up the dmb_node under dmb_ht_lock, drop the lock and only then
operate on the node's refcount. Nothing keeps the node alive across
that window: __dibs_lo_unregister_dmb() removes the node from the hash
table under the write lock and immediately frees it.
A concurrent final put can therefore free the node between the lookup
and the refcount operation:
CPU0 (attach) CPU1 (owner unregisters)
read_lock_bh(&dmb_ht_lock)
find dmb_node (refcnt == 1)
read_unlock_bh(&dmb_ht_lock)
refcount_dec_and_test() 1 -> 0
write_lock_bh(&dmb_ht_lock)
hash_del(&dmb_node->list)
write_unlock_bh(&dmb_ht_lock)
kfree(dmb_node)
refcount_inc_not_zero(&dmb_node->refcnt) <-- use-after-free
The same window exists for the refcount_dec_and_test() calls in the
detach and unregister paths.
Close the race structurally by making hash table membership and the
refcount transitions atomic with respect to each other:
- Perform the final refcount_dec_and_test() and hash_del() in a single
dmb_ht_lock write-side critical section, in both the unregister and
the detach path. Freeing the node still happens after the lock is
dropped, which is safe because a node whose refcount reached zero has
left the hash table and can no longer be found.
- This establishes the invariant that any node found in the hash table
holds at least one reference, and that the final reference can only
be dropped under the write lock. dibs_lo_attach_dmb() can thus take
its reference with a plain refcount_inc() while still holding the
read lock; refcount_inc_not_zero() is no longer needed.
__dibs_lo_unregister_dmb() no longer touches the hash table and is
renamed to dibs_lo_free_dmb() accordingly.
Note: commit cc21191b584c ("dibs: Move data path to dibs layer") moved
the code to its current location; the race was introduced earlier by
commit c3a910f2380f ("net/smc: implement DMB-merged operations of
loopback-ism").
Tested SMC-D via ISM and dibs loopback. |
| Use-after-free in the DOM: Core & HTML component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| Use-after-free in the Graphics: ImageLib component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| Use-after-free in the Graphics: Text component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| Use-after-free in the JavaScript: WebAssembly component. This vulnerability was fixed in Firefox 154, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: hold sk properly in iso_conn_ready
sk deref in iso_conn_ready must be done either under conn->lock, or
holding a refcount, to avoid concurrent close. conn->sk is currently
accessed without either:
[Task 1] [Task 2]
iso_sock_release
iso_conn_ready
sk = conn->sk
lock_sock(sk)
conn->sk = NULL
lock_sock(sk)
release_sock(sk)
iso_sock_kill(sk)
UAF on sk deref
Fix possible UAF by holding sk refcount in iso_conn_ready(). Also
recheck after lock_sock that the socket is still valid. Adjust locking
so conn->sk is cleared only under lock_sock. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/iommufd: Fix IOPF group ownership UAF
iopf_group_alloc() links each last-page IOPF group into the generic IOPF
pending list before invoking the domain fault handler.
iommufd_fault_iopf_handler() also queued an accepted group in the
IOMMUFD deliver list without removing it from the generic pending list.
When detach or HWPT replacement drops the device's IOPF reference count
to zero, an IOMMU driver may call iopf_queue_remove_device(). That
function responds to and frees groups through the generic pending list
without removing the same groups from IOMMUFD's deliver list or response
xarray. A later read, response, or cleanup can then access the freed
group and cause a UAF.
Fix this by dequeuing an accepted group from the generic pending list
before IOMMUFD queues it for userspace response.
Make iopf_group_response() send a response regardless of pending-list
membership, so the dequeued group can still be completed by IOMMUFD. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in __close_file_table_ids()
A ksmbd_file can remain alive after logical close while another session
holds a temporary reference obtained through ksmbd_lookup_fd_inode().
ksmbd_close_fd() currently marks the file closed and drops the idr-owned
reference, but leaves the pointer published in the closing session's idr
until the final reference is dropped.
If the foreign holder performs the final ksmbd_fd_put(), __put_fd_final()
supplies the foreign session's file table to __ksmbd_close_fd(). The object
is then freed without being removed from its owner's idr, and the owner
session later dereferences the stale pointer during file-table teardown.
Remove the volatile id from the owner's idr while ksmbd_close_fd() still
holds that table's lock, and clear volatile_id before dropping
the idr-owned reference. A later foreign final put then only performs
physical destruction and cannot remove the object from the wrong table. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: fix race of kfree vs kref_get_unless_zero
hci_conn::iso_data is accessed and modified without lock or RCU.
This leads to a race
[Task hdev->workqueue] [Task 2]
iso_recv iso_conn_put(conn)
conn = LOAD hcon->iso_data iso_conn_free(conn)
iso_conn_hold_unless_zero(conn) hcon->iso_data = NULL
kfree(conn)
kref_get_unless_zero(&conn->ref) /* UAF */
and also to races in iso_conn_add() vs. iso_conn_free().
Fix by adding spinlock hci_conn::proto_lock and using it to guard
hci_conn::iso_data. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: avoid deadlocks in iso_sock_timeout
iso_sock_timeout() takes lock_sock, so sync disabling the timer while
holding that lock may deadlock.
iso_sock_timeout() may also run concurrently with iso_conn_del(), which
leads to UAF
[Task 1] [Task hdev->workqueue]
iso_sock_timeout iso_conn_del
iso_conn_hold_unless_zero iso_chan_del
`------------> iso_conn_put
caller frees hcon
iso_conn_put
iso_conn_free
conn->hcon->iso_data = NULL; /* UAF */
Fix the deadlock by removing the disable from the lock_sock sections.
Move the timer from iso_conn to iso_pinfo to decouple it from iso_conn
which may need to be freed in lock_sock section. Convert some of the
clear_timer to disable_timer. |
