| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: itg3200: fix i2c read into the wrong stack location
itg3200_read_all_channels() takes `__be16 *buf' as a parameter and
fills the i2c_msg destination as `(char *)&buf'. Since `buf' is the
parameter (a pointer), `&buf' is the address of the local pointer
slot on the stack of itg3200_read_all_channels(), not the address
of the caller's scan buffer. The (char *) cast hides the type
mismatch.
i2c_transfer() therefore writes ITG3200_SCAN_ELEMENTS * sizeof(s16)
= 8 bytes into the parameter's stack slot, which is discarded when
the function returns. The caller's scan buffer in
itg3200_trigger_handler() is never written to, so
iio_push_to_buffers_with_timestamp() pushes uninitialised stack
contents to userspace via /dev/iio:deviceX every scan -- both a
functional bug (no actual gyroscope or temperature data is
delivered through the triggered buffer) and an information leak.
The non-buffered read_raw() path is unaffected: it goes through
itg3200_read_reg_s16() which uses `&out' on a local s16 value,
where that is correct.
Drop the spurious `&' so the i2c read writes into the caller's
buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: adis16260: fix division by zero in write_raw
Add a validation check for the sampling frequency value before using it
as a divisor. A user writing zero to the sampling_frequency sysfs
attribute triggers a division by zero in the kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: mhz19b: reject oversized serial replies
mhz19b_receive_buf() appends each serdev chunk into the fixed
MHZ19B_CMD_SIZE receive buffer and advances buf_idx by len without
checking that the chunk fits in the remaining space. A large callback
can therefore overflow st->buf before the command path validates the
reply.
Reset the reply state before each command and reject oversized serial
replies before copying them into the fixed buffer. When an oversized
reply is detected, wake the waiter and report -EMSGSIZE instead of
overwriting st->buf. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: scd30: fix division by zero in write_raw
Add a zero check for val2 before using it as a divisor when setting the
sampling frequency. A user writing a zero fractional part to the
sampling_frequency sysfs attribute triggers a division by zero in the
kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: Fix DMA fence leak in iio_buffer_enqueue_dmabuf()
iio_buffer_enqueue_dmabuf() allocates a struct iio_dma_fence (104 bytes,
kmalloc-128) via kmalloc_obj()+dma_fence_init(), which sets the initial
kref to 1. It then calls dma_resv_add_fence() which takes a second
reference (kref=2), and stores a raw pointer in block->fence.
On the success path the function returns without calling dma_fence_put()
to release the initial reference, so every buffer enqueue permanently
leaks one kmalloc-128 allocation.
The iio_buffer_cleanup() work item only releases the temporary reference
taken during completion signalling by iio_buffer_signal_dmabuf_done();
the initial reference from dma_fence_init() is never released.
With four iio_rwdev instances at 240kHz and 512 samples per buffer,
this produces ~1875 kmalloc-128 allocations per second matching the
observed slab growth exactly. A test with ftrace confirmed that the
dma_fence_destroy event was never triggered.
Fix by calling dma_fence_put() after dma_resv_add_fence(), transferring
ownership of the fence to the DMA reservation object. The DMA fence then
gets properly discarded after being signalled. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: omninet: fix memory corruption with small endpoint
Make sure that the bulk-out buffers are at least as large as the
hardcoded transfer size to avoid user-controlled slab corruption should
a malicious device report a smaller endpoint max packet size than
expected. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: atmel_mxt_ts - fix boundary check in mxt_prepare_cfg_mem
When a configuration file provides an object size that is larger than the
driver's known mxt_obj_size(object), the driver intends to discard the
extra bytes.
The loop iterates using for (i = 0; i < size; i++). Inside the loop, the
condition to skip processing extra bytes is:
if (i > mxt_obj_size(object))
continue;
Since i is a 0-based index, the valid indices for the object are 0 through
mxt_obj_size(object) - 1.
When i == mxt_obj_size(object), the condition evaluates to false, and the
code processes the byte instead of discarding it.
This causes the code to calculate byte_offset = reg + i - cfg->start_ofs
and writes the byte there, overwriting exactly one byte of the adjacent
instance or object.
Update the boundary check to skip extra bytes correctly by using >=. |
| In the Linux kernel, the following vulnerability has been resolved:
uio: uio_pci_generic_sva: fix double free of devm_kzalloc() memory
uio_pci_sva allocates struct uio_pci_sva_dev with devm_kzalloc() in
probe(), but then calls kfree(udev) both on the probe() error path
(label out_free) and again in remove().
Because devm_kzalloc() allocations are devres-managed and are freed
automatically when the device is detached (including after a failing
probe() and during driver unbind), the explicit kfree() can lead to a
double free.
If probe() fails after devm_kzalloc(), the error path frees udev and
devres cleanup will free it again when the core unwinds the partially
bound device. On normal driver removal, remove() frees udev and devres
will free it again when the device is detached.
This issue was identified by a static analysis tool I developed and
confirmed by manual review. Fix by removing the manual kfree() calls
and dropping the now-unused label. |
| In the Linux kernel, the following vulnerability has been resolved:
usbip: vudc: Fix use after free bug in vudc_remove due to race condition
This patch follows up Zheng Wang's 2023 report of a use-after-free in
vudc_remove(). The original thread stalled on Shuah Khan's request for
runtime testing of the unplug/unbind path. This patch supplies that
testing and keeps Zheng's original fix shape.
In vudc_probe(), v_init_timer() binds udc->tr_timer.timer to v_timer().
usbip_sockfd_store() starts the timer via v_start_timer()/v_kick_timer().
vudc_remove() can then free the containing struct vudc while the timer is
still pending or executing.
KASAN confirms the race on an unpatched x86_64 QEMU guest with
CONFIG_KASAN=y, CONFIG_USBIP_VUDC=y, CONFIG_USB_ZERO=y, and a tight loop
that repeatedly writes a socket fd to usbip_sockfd, closes the socket
pair, and unbinds/rebinds usbip-vudc.0:
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x8ba/0x8e0
Write of size 8 at addr ffff888001b80740 by task trigger_and_unb/239
Allocated by task 239:
vudc_probe+0x4d/0xaa0
Freed by task 239:
kfree+0x18f/0x520
device_release_driver_internal+0x388/0x540
unbind_store+0xd9/0x100
This lands in the timer core rather than v_timer() itself because the
embedded timer_list is being walked after its containing struct vudc has
already been freed. The underlying lifetime bug is the same one Zheng
reported.
With v_stop_timer() called from vudc_remove() and the timer deleted
synchronously, the same harness completed 5000 bind/unbind iterations
with no KASAN report. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: usbtmc: check URB actual_length for interrupt-IN notifications
USBTMC devices can use an optional interrupt endpoint for notification
messages. These typically contain two-byte headers indicating the
payload format, but the driver does not check if these headers are
present before accessing the data buffers. In cases where the URB
actual_length is not enough to fit these headers, the driver will either
cause an out-of-bounds read, or consume stale leftover data from a
previous notification.
Fix by checking if actual_data contains enough bytes for the headers,
otherwise resubmit URB to the interrupt endpoint. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: belkin_sa: validate interrupt status length
The Belkin interrupt callback treats interrupt data as a four-byte
status report and reads LSR/MSR fields at offsets 2 and 3. The
interrupt-in buffer length is derived from endpoint wMaxPacketSize, and
short interrupt transfers may complete successfully with a smaller
actual_length.
Check the completed interrupt packet length before parsing status
fields so short interrupt endpoints and short successful packets are
ignored instead of causing out-of-bounds or stale status-byte reads.
KASAN report as below:
BUG: KASAN: slab-out-of-bounds in belkin_sa_read_int_callback()
Read of size 1
Call trace:
belkin_sa_read_int_callback() (drivers/usb/serial/belkin_sa.c:202)
__usb_hcd_giveback_urb() (drivers/usb/core/hcd.c:1630)
dummy_timer() (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: cypress_m8: validate interrupt packet headers
cypress_read_int_callback() parses the interrupt-in buffer according to
the selected Cypress packet format. Format 1 has a two-byte status/count
header and format 2 has a one-byte combined status/count header. The
usb-serial core sizes the interrupt-in buffer from the endpoint
descriptor's wMaxPacketSize, and successful interrupt transfers can
complete short when URB_SHORT_NOT_OK is not set.
Check that the completed packet contains the selected header before
reading it. Malformed short reports are ignored and the interrupt URB is
resubmitted through the existing retry path, preventing out-of-bounds
header-byte reads.
KASAN report as below:
KASAN slab-out-of-bounds in cypress_read_int_callback+0x240/0x7f0
Read of size 1
Call trace:
cypress_read_int_callback() (drivers/usb/serial/cypress_m8.c:1009)
__usb_hcd_giveback_urb()
dummy_timer()
[ johan: use constants in header length sanity checks ] |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: digi_acceleport: fix memory corruption with small endpoints
Add the missing bulk-out buffer size sanity checks to avoid
out-of-bounds memory accesses or slab corruption should a malicious
device report smaller buffers than expected. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: keyspan: fix missing indat transfer sanity check
Add the missing sanity check on the size of usa49wg indat transfers to
avoid parsing stale or uninitialised slab data. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: mxuport: fix memory corruption with small endpoint
Make sure that the bulk-out endpoint max packet size is at least eight
bytes to avoid user-controlled slab corruption should a malicious device
report a smaller size. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: mct_u232: fix memory corruption with small endpoint
The driver overrides the maximum transfer size for a specific device
which only accepts 16 byte packets for its 32 byte bulk-out endpoint.
Make sure to never increase the maximum transfer size to prevent slab
corruption should a malicious device report a smaller endpoint max
packet size than expected. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: mct_u232: fix missing interrupt-in transfer sanity check
Add the missing sanity check on the size of interrupt-in transfers to
avoid parsing stale or uninitialised slab data (and leaking it to user
space). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: composite: fix integer underflow in WebUSB GET_URL handling
The WebUSB GET_URL handler in composite_setup() narrows
landing_page_length to fit the host-supplied wLength using
landing_page_length = w_length
- WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH + landing_page_offset;
If wLength is smaller than WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH the
unsigned subtraction wraps, and the subsequent
memcpy(url_descriptor->URL,
cdev->landing_page + landing_page_offset,
landing_page_length - landing_page_offset);
ends up copying close to UINT_MAX bytes from cdev->landing_page into
cdev->req->buf. KASAN reports a slab-out-of-bounds in composite_setup
on the kmalloc-2k gadget_info allocation, and FORTIFY_SOURCE traps the
memcpy as a 4294967293-byte field-spanning write into
url_descriptor->URL (size 252).
A USB host can reach this from a single SETUP packet against any
gadget that has webusb/use=1 and a landingPage configured.
Handle the small-wLength case before the math: when the host requested
fewer bytes than the URL descriptor header, only the header is
meaningful and no URL bytes need to be copied. Setting
landing_page_length to landing_page_offset makes the existing memcpy a
no-op and leaves the descriptor returned to the host unchanged for all
larger wLength values. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_fs: copy only received bytes on short ep0 read
ffs_ep0_read() allocates its control-OUT data buffer with
kmalloc() (not kzalloc) at the Length value from the Setup
packet, then copies that full len to userspace regardless of
how many bytes were actually received:
data = kmalloc(len, GFP_KERNEL);
...
ret = __ffs_ep0_queue_wait(ffs, data, len);
if ((ret > 0) && (copy_to_user(buf, data, len)))
ret = -EFAULT;
__ffs_ep0_queue_wait() returns req->actual, which on a short
control OUT transfer is strictly less than len. The
copy_to_user() call still copies len bytes, so on a short OUT
the last (len - ret) bytes of the kmalloc() buffer --
uninitialised slab residue -- are delivered to the FunctionFS
daemon.
Short ep0 OUT completions are specified USB control-transfer
behavior and are produced by in-tree UDCs:
* dwc2 continues on req->actual < req->length for ep0 DATA OUT
(short-not-ok is the only ep0-OUT stall path).
* aspeed_udc ends ep0 OUT on rx_len < ep->ep.maxpacket.
* renesas_usbf logs "ep0 short packet" and completes the
request.
* dwc3 stalls on short IN but not on short OUT.
A short ep0 OUT is therefore not evidence of a broken UDC; it is
a normal condition f_fs has to cope with. The sibling gadgetfs
implementation in drivers/usb/gadget/legacy/inode.c already does
this correctly via min(len, dev->req->actual) before
copy_to_user(). This patch brings f_fs.c to the same safe
pattern rather than trimming at a defensive layer.
The bug is reached from the FunctionFS device node, which in
real deployments is owned by the privileged gadget daemon
(adbd, UMS, composite gadget services, etc.); it is not
reachable from unprivileged userspace. Linux host stacks
normally reject short-wLength control OUTs before they reach
the gadget, so reproducing this required a build that
bypasses that host-side check. With the bypass in place, a
1-byte payload on a 64-byte Setup produces 63 bytes of
non-canary slab residue in the daemon's read buffer.
Fix by copying only ret (actually received) bytes to
userspace. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: property: Reject dir_len < 4 to prevent size_t underflow
On the non-root path, __tb_property_parse_dir() takes dir_len from
entry->length (u16 widened to size_t). Two distinct OOB conditions
follow when entry->length < 4:
1. The non-root path begins with kmemdup(&block[dir_offset],
sizeof(*dir->uuid), ...) which always reads 4 dwords from
dir_offset. tb_property_entry_valid() only enforces
dir_offset + entry->length <= block_len, so a crafted entry
with dir_offset close to the end of the property block and
entry->length in 0..3 passes that gate but lets the UUID copy
run off the block (e.g. dir_offset = 497, dir_len = 3 in a
500-dword block reads block[497..501]).
2. After the kmemdup, content_len = dir_len - 4 underflows size_t
to ~SIZE_MAX, nentries becomes SIZE_MAX / 4, and the entry
walk runs OOB on each iteration until an entry fails
validation or the kernel oopses on an unmapped page.
Reject dir_len < 4 on the non-root path *before* the UUID kmemdup,
which closes both holes.
Also move INIT_LIST_HEAD(&dir->properties) up to immediately after
the dir allocation so the new error-return path (and the existing
uuid-alloc failure path) calling tb_property_free_dir() sees a
walkable list rather than the zero-initialized NULL next/prev that
list_for_each_entry_safe() would oops on. |
