| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Dell Wyse Management Suite (WMS), versions prior to 2605.0.2, contain an Unrestricted Upload of File with Dangerous Type vulnerability. A high privileged attacker with remote access could potentially exploit this vulnerability, leading to Remote Code Execution. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix divide-by-zero in calculate_mcache_setting on zero viewport
If a plane reaches calculate_mcache_setting with a zero-area viewport,
calculate_mcache_setting exits early with num_mcaches == 0 and
mvmpg_width/height == 0. This will cause a divide-by-zero panic and can
also cause an underflow on num_mcaches.
Fix this by changing calculate_mcache_setting to bool and adding guards
after each calculate_mcache_row_bytes call. If num_mcaches or
mvmpg_width/height is zero, return a false. Callers will propagate the
failure as a rejected mode, which prevents the panic.
(cherry picked from commit 29c0f7c655f47bcbd575ff75e58480df6ec3c9da) |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: avoid heap allocation for free-cluster readahead state
get_nr_free_clusters() allocates a temporary file_ra_state before it
publishes the precomputed free cluster count, sets NVolFreeClusterKnown(),
and wakes vol->free_waitq. If that allocation fails, the worker returns
without setting the flag or waking waiters, so callers waiting for the free
count can block indefinitely.
The readahead state is only used synchronously while scanning the bitmap.
Keep it on the stack and pass it by address to the readahead helper. This
eliminates the early allocation failure path instead of adding a special
case that publishes a conservative count and wakes the waitqueue.
Zero-initialize the on-stack state because file_ra_state_init() only sets
ra_pages and prev_pos.
Apply the same treatment to __get_nr_free_mft_records(), which scans the
MFT bitmap with the same short-lived readahead state. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: avoid full teardown before work setup in probe
rt2x00lib_probe_dev() uses the full rt2x00lib_remove_dev() teardown for
all probe failures. However, drv_data allocation and workqueue allocation
can fail before intf_work, autowakeup_work and sleep_work have been
initialized.
Do not enter the full remove path until the probe has reached the point
where those work items are set up. Return directly for drv_data allocation
failure, and use a small early cleanup path for workqueue allocation
failure.
This issue was found by our static analysis tool and then confirmed by
manual review of rt2x00lib_probe_dev() and rt2x00lib_remove_dev(). The
early probe exits should not call a common teardown path that assumes the
later work setup has already completed.
A QEMU PoC forced alloc_ordered_workqueue() to fail before the work
initializers are reached. The resulting fail path entered
rt2x00lib_remove_dev(), and DEBUG_OBJECTS reported invalid work drains with
rt2x00lib_probe_dev() and rt2x00lib_remove_dev() in the stack. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/uaccess: correct check for CONFIG_PPC_E500 in mask_user_address()
mask_user_address() incorrectly checks for CONFIG_E500 instead of
CONFIG_PPC_E500, causing mask_user_address_isel() to not be used on
E500 hardware. Fix the check to use the correct name. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: cyw: fix heap overflow on a short auth frame
brcmf_notify_auth_frame_rx() takes the frame length from the firmware
event and copies the frame body with the management header offset
subtracted:
u32 mgmt_frame_len = e->datalen - sizeof(struct brcmf_rx_mgmt_data);
...
memcpy(&mgmt_frame->u, frame,
mgmt_frame_len - offsetof(struct ieee80211_mgmt, u));
The only length check is e->datalen >= sizeof(*rxframe), so mgmt_frame_len
can be anything from 0 up. offsetof(struct ieee80211_mgmt, u) is 24. When
mgmt_frame_len is below that, the subtraction wraps as an unsigned value to
a huge length. The memcpy then runs far past the kzalloc'd buffer. A
malicious or malfunctioning AP can make the frame short during the
external SAE auth exchange, so this is a remotely triggered heap overflow.
Reject frames shorter than the management header offset before the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-fence: Make dma_fence_dedup_array() robust against 0-count input
dma_fence_dedup_array() returns 1 when called with num_fences == 0:
the for-loop body never executes, j stays at 0, and the final
`return ++j` yields 1. This contradicts both the kernel-doc ("Return:
Number of unique fences remaining in the array") and the natural
expectation that 0 input gives 0 output.
The caller __dma_fence_unwrap_merge() bails out via the
`if (count == 0 || count == 1)` fast path and so is save.
But amdgpu_userq_wait_*() could reach the dedup call with a zero local
count and dereference an uninitialized fence slot in the array.
Make the contract match the documentation by returning 0 early. This
also skips an unnecessary sort() call on an empty array. |
| In Progress ShareFile Storage Zones Controller v5.12.5 and below, a party with valid zone credentials can perform path traversal using resumable upload initiation endpoint, allowing the party to write arbitrary content to any location writable by the application's service account. This may result in the execution of attacker-supplied code. |
| In the Linux kernel, the following vulnerability has been resolved:
device property: initialize the remaining fields of fwnode_handle in fwnode_init()
If a firmware node is allocated on the stack (for instance: temporary
software node whose life-time we control) or on the heap - but using a
non-zeroing allocation function - and initialized using fwnode_init(),
its secondary pointer will contain uninitialized memory which likely
will be neither NULL nor IS_ERR() and so may end up being dereferenced
(for example: in dev_to_swnode()). Set fwnode->secondary to NULL on
initialization. While at it: initialize the remaining fields of struct
fwnode_handle too just to be sure.
[ Fix typo in commit message. - Danilo ] |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btrtl: validate firmware patch bounds
rtlbt_parse_firmware() copies patch_length - 4 bytes before appending the
firmware version. A malformed firmware patch shorter than the version field
can make this subtraction underflow and turn the copy into an oversized
read and write during Bluetooth setup.
The existing patch_offset + patch_length check can also wrap on 32-bit
architectures. Validate the patch length and range without arithmetic
overflow before allocating or copying the patch. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: use parsed transport offset in SCTP state lookup
set_sctp_state() reads the SCTP chunk header again in order to drive the
IPVS SCTP state table. For IPv6 it computes the offset with
sizeof(struct ipv6hdr), while the surrounding IPVS code uses iph.len from
ip_vs_fill_iph_skb(), where ipv6_find_hdr() has already skipped
extension headers and found the real transport header.
This makes the state machine read from the wrong offset for IPv6 SCTP
packets that carry extension headers. For example, an INIT packet with an
8-byte destination options header can be scheduled correctly by
sctp_conn_schedule(), but set_sctp_state() reads the first byte of the
SCTP verification tag as a DATA chunk type. The connection then moves
from NONE to ESTABLISHED instead of INIT1, gets the longer established
timeout, and updates the active/inactive destination counters
incorrectly. This happens even though the SCTP handshake has not
completed.
Use the parsed transport offset passed down from ip_vs_set_state() for
the SCTP chunk-header lookup. For IPv4 and IPv6 packets without
extension headers this preserves the existing offset. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Fix missing dirty page tracking in {pte,pmd}_wrprotect()
When hardware page table walker (PTW) is enabled on LoongArch, the CPU
may set _PAGE_DIRTY directly in the page table entry during a write TLB
miss, without going through the software TLB store handler. The software
TLB store handler (tlbex.S:254) sets both _PAGE_DIRTY and_PAGE_MODIFIED
together:
ori t0, t0, (_PAGE_VALID | _PAGE_DIRTY | _PAGE_MODIFIED)
Since hardware PTW only sets _PAGE_DIRTY, the software-only bit, i.e.
_PAGE_MODIFIED is left unchanged. This creates a window where a PTE has
_PAGE_DIRTY set (hardware knows the page is dirty) but _PAGE_MODIFIED
clear (software is unaware).
When fork()/clone() triggers copy-on-write, __copy_present_ptes() calls
pte_wrprotect(), which unconditionally clears both the _PAGE_WRITE and
_PAGE_DIRTY bits:
pte_val(pte) &= ~(_PAGE_WRITE | _PAGE_DIRTY);
Since _PAGE_MODIFIED was never set, the dirtiness information is lost
completely. Subsequently, when memory pressure triggers page reclaim,
page_mkclean() / try_to_unmap() sees the page as clean (i.e. pte_dirty()
returns false) and the page may be freed without writeback, causing data
corruption.
Fix this by propagating the _PAGE_DIRTY bit to the _PAGE_MODIFIED bit in
both pte_wrprotect() and pmd_wrprotect() before clearing writeable bits:
if (pte_val(pte) & _PAGE_DIRTY)
pte_val(pte) |= _PAGE_MODIFIED;
The pmd_wrprotect() fix handles the CONFIG_TRANSPARENT_HUGEPAGE case,
where pmd entries need the same treatment.
This ensures the software dirty tracking bit (checked by pte_dirty() and
pmd_dirty(), which read both the _PAGE_DIRTY and _PAGE_MODIFIED bits) is
preserved across fork COW write-protection.
The issue was found by the LTP madvise09 test case, which exercises page
reclaim after "madvise(MADV_FREE), write and fork" operation sequence on
private anonymous mappings. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: admin-gate legacy LLSEC dump operations
In net/ieee802154/netlink.c, the legacy IEEE802154_NL family ops table
builds the LLSEC dump entries (LLSEC_LIST_KEY, LLSEC_LIST_DEV,
LLSEC_LIST_DEVKEY, LLSEC_LIST_SECLEVEL) with IEEE802154_DUMP() which
sets no .flags, so generic netlink runs them ungated. The modern
nl802154 family admin-gates the equivalent reads via
NL802154_CMD_GET_SEC_KEY and friends with .flags = GENL_ADMIN_PERM.
Any local uid that can open AF_NETLINK / NETLINK_GENERIC can resolve
the "802.15.4 MAC" family and dump LLSEC_LIST_KEY on any wpan netdev
that has an LLSEC key installed; the dump handler writes the raw
16-byte AES-128 key bytes (IEEE802154_ATTR_LLSEC_KEY_BYTES, copied
verbatim from struct ieee802154_llsec_key.key) into the reply.
Recovering the AES key compromises 802.15.4 LLSEC link confidentiality
and authenticity, since LLSEC uses CCM* and the same key authenticates
and encrypts frames.
Impact: any local uid with no capabilities can read the raw 16-byte
AES-128 LLSEC key from the kernel keytable on any wpan netdev that has
an administrator-installed LLSEC key, by issuing an LLSEC_LIST_KEY
dump on the legacy IEEE802154_NL generic-netlink family.
Introduce IEEE802154_DUMP_PRIV() mirroring IEEE802154_DUMP() but
setting .flags = GENL_ADMIN_PERM, and use it for the four LLSEC dump
entries. LIST_PHY and LIST_IFACE retain IEEE802154_DUMP() because the
modern nl802154 family exposes their equivalents to unprivileged
readers by design (NL802154_CMD_GET_WPAN_PHY and
NL802154_CMD_GET_INTERFACE carry "can be retrieved by unprivileged
users" annotations). |
| In the Linux kernel, the following vulnerability has been resolved:
net: ip6_gre: require CAP_NET_ADMIN in the device netns for changelink
ip6gre_changelink() and ip6erspan_changelink() operate on at most two
netns, dev_net(dev) and the tunnel link netns t->net. They differ once
the device is created in or moved to a netns other than the one the
request runs in. The rtnl changelink path checks CAP_NET_ADMIN only
against dev_net(dev), so a caller privileged there but not in t->net can
rewrite a tunnel that lives in t->net.
Gate both ops on rtnl_dev_link_net_capable() at their top, before any
attribute is parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sit: require CAP_NET_ADMIN in the device netns for changelink
ipip6_changelink() operates on at most two netns, dev_net(dev) and the
tunnel link netns t->net. They differ once the device is created in or
moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in t->net can rewrite a tunnel that
lives in t->net.
Gate ipip6_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed. sit was the one tunnel type not covered
by the recent series that added this check to the other changelink()
handlers. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: macsec: fix use-after-free of metadata_dst on RX SC delete
When an offloaded MACsec RX SC is deleted, macsec_del_rxsc_ctx() freed
the per-SC metadata_dst with metadata_dst_free(), which kfree()s the
object unconditionally and ignores the dst reference count. The RX
datapath in mlx5e_macsec_offload_handle_rx_skb() looks up the SC under
rcu_read_lock() via xa_load(), takes a reference with dst_hold() and
attaches the dst to the skb with skb_dst_set(). A reader that already
obtained the rx_sc pointer can race with the delete path and operate on
freed memory.
Fix the owner side by dropping the reference with dst_release() instead
of freeing unconditionally, and convert the RX datapath to
dst_hold_safe() so a reader racing the SC delete cannot attach a dst
whose last reference was just dropped; only attach it when a reference
was actually taken.
mlx5e_macsec_add_rxsc() also published sc_xarray_element via xa_alloc()
before rx_sc->md_dst was allocated and initialised, so a datapath reader
that looked the SC up by fs_id could observe rx_sc with md_dst still
NULL or, on weakly-ordered architectures, a non-NULL md_dst pointer
whose contents were not yet visible. NULL-check the xa_load() result and
md_dst on the datapath, and reorder add_rxsc() so the xa_alloc() publish
happens only after md_dst is fully initialised; the xarray RCU publish
then pairs with the rcu_read_lock()/xa_load() in the datapath.
Note: macsec_del_rxsc_ctx() also kfree()s rx_sc->sc_xarray_element
without an RCU grace period while the same datapath reads it under
rcu_read_lock(); that is a separate pre-existing issue left to a
follow-up patch.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: use unconditional synchronize_rcu() in isotp_release()
isotp_notify() unregisters the (RCU) CAN filters via can_rx_unregister()
and clears so->bound without waiting for a grace period. isotp_release()
uses so->bound to decide whether it needs to call synchronize_rcu()
before cancelling so->rxtimer, so when NETDEV_UNREGISTER runs first it
skips that synchronize_rcu() and can cancel the timer while an
in-flight isotp_rcv() is still executing and about to re-arm it via
isotp_send_fc(), leading to a use-after-free timer callback on the
freed socket.
sakisho-bot remarked a problem with rtnl_lock held in isotp_notify(),
therefore make isotp_release() always call synchronize_rcu() before
cancelling the timers, regardless of so->bound. This still closes the
original race (isotp_notify() clearing so->bound without waiting for
in-flight isotp_rcv() callers before isotp_release() cancels the RX
timer) without adding any RCU wait to the netdevice notifier path. |
| In the Linux kernel, the following vulnerability has been resolved:
cpu: hotplug: Preserve per instance callback errors
cpuhp_invoke_callback() unwinds earlier callbacks for the same
hotplug state when one instance fails. The rollback path currently
reuses ret, so a successful rollback can hide the original error and
make the failed transition look successful.
Keep the rollback result separate from the original error. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/resctrl: Fix use-after-free during unmount
During unmount or failure teardown all mon_data structures that contain
monitoring event file private data are freed after which kernfs nodes are
removed. However, the RDT_DELETED flag is never set for the statically
allocated default resource group.
A concurrent reader of an event file associated with the default resource
group may, after dropping kernfs active protection, block on rdtgroup_mutex
while unmount proceeds to free the file private data and destroy the kernfs
node without waiting for the reader.
When the mutex is released, the reader wakes up, observes that RDT_DELETED
is not set for the default group, and dereferences the already-freed
file private data.
The scenario can be depicted as follows:
CPU0 CPU1
/*
* Default resource group's
* monitoring data accessible via
* kernfs file with kernfs_node::priv
* pointing to a struct mon_data.
* User opens the file for reading.
*/
rdtgroup_mondata_show() /* arch encounters fatal error */
rdtgroup_kn_lock_live() resctrl_exit()
atomic_inc(&rdtgroup_default.waitcount) cpus_read_lock()
kernfs_break_active_protection(kn) mutex_lock(&rdtgroup_mutex)
cpus_read_lock() resctrl_fs_teardown()
mutex_lock(&rdtgroup_mutex) rmdir_all_sub()
mon_put_kn_priv()
/* Delete all mon_data structures */
rdtgroup_destroy_root()
kernfs_destroy_root()
rdtgroup_default.kn = NULL
mutex_unlock(&rdtgroup_mutex)
/*
* rdtgroup_default.flags is empty so
* rdtgroup_kn_lock_live() returns
* &rdtgroup_default
*/
md = of->kn->priv;
/* md points to freed mon_data */
Set RDT_DELETED for the default group unconditionally since the flag does
not lead to the freeing of this statically allocated group.
Do not allow a new resctrl mount if there are any waiters on default group
of previous mount. A new mount will re-initialize the default group that
would appear to waiters from previous mount as though the default group is
accessible causing them to access the mon_data structures from the previous
mount that have been removed. |
