| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Validate string descriptors
The string descriptor length includes a two-byte header while the UTF-16
payload starts after it. utf16s_to_utf8s() expects a count of UTF-16 code
units, not bytes. Passing the payload byte count can make it read beyond
the descriptor buffer.
Validate that the payload has an even byte count, pass a code-unit count to
the converter, and allocate sufficient UTF-8 output space.
The raw string buffer starts after the descriptor header but its size is
bLength. Copying bLength bytes from that pointer can read beyond the
response buffer.
Allocate a zeroed bLength-sized buffer and copy only the UTF-16
payload. This preserves the raw buffer size consumed by the RPMB device-ID
ABI while avoiding the overread. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: oc-tiny: switch to managed controller allocation
The controller is allocated with the non-managed spi_alloc_host() while
the interrupt is registered with devm_request_irq(). During removal,
spi_bitbang_stop() only unregisters the controller; the subsequent
spi_controller_put() then frees the controller together with its
embedded driver-private devdata, which is the IRQ handler's dev_id. The
devm_request_irq() release action (free_irq()), which drains the
handler, does not run until after .remove() returns. A late or latched
interrupt can therefore reach tiny_spi_irq() and dereference
already-freed memory (e.g. hw->base).
Switch to devm_spi_alloc_host() so that the devres LIFO order releases
the controller only after free_irq() has drained the handler, and drop
the now-redundant spi_controller_put() from .remove(). The probe error
path is simplified to direct returns.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix UAF when probe runs concurrent to dyn ID removal
Dynamic IDs are only guaranteed to be valid when dynids.lock is held,
as remove_id_store() can free the node. Thus, make a copy in
pci_match_device(). Also, clarify that the id parameter is only valid
during probe. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix BUG in nilfs_copy_dirty_pages() on dirty state mismatch
Syzbot reported a kernel BUG triggered within nilfs_copy_dirty_pages(),
which copies dirty DAT file folios/pages to its shadow page cache. The
BUG occurs when a retrieved dirty folio/page unexpectedly loses its
'dirty' status.
This issue arises because, since the commit referenced below, the 'dirty'
flag of a folio/page can be cleared asynchronously after the filesystem
detects metadata corruption and transitions to read-only mode.
Resolve the issue by returning an -EROFS error if the filesystem has
transitioned to read-only mode. Also change the behavior to issue a
kernel warning only once instead of triggering a kernel BUG when this
unexpected 'dirty' state is detected while the filesystem is not in
read-only mode. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/cxgb4: Fix dereg_skb leak and double free in write_tpt_entry()
When the device is in the fatal error state, write_tpt_entry() returns -EIO
before handing the caller's preallocated skb to the transmit path; its
allocation-failure returns do the same. c4iw_dereg_mr() ignores the error
and frees mhp, leaking mhp->dereg_skb. c4iw_get_dma_mr() instead frees the
skb a second time after dereg_mem() already consumed it, a double free.
Make write_tpt_entry() the sole owner of a non-NULL skb, freeing it on
every return preceding handoff to c4iw_ofld_send(): fatal error, tpt and
stag allocation failure. c4iw_ofld_send() consumes the skb on success and
error alike, so drop the redundant kfree_skb() in c4iw_get_dma_mr() after
dereg_mem(). |
| In the Linux kernel, the following vulnerability has been resolved:
spi: davinci: switch to managed controller allocation
The controller is allocated with the non-managed spi_alloc_host() while
the interrupt is registered with devm_request_threaded_irq(). During
removal, spi_bitbang_stop() only unregisters the controller; the
subsequent spi_controller_put() then frees the controller together with
its embedded davinci_spi devdata, which is the IRQ handler's dev_id.
The devm_request_threaded_irq() release action (free_irq()), which
drains the handler, does not run until after .remove() returns. A late
or latched interrupt can therefore reach davinci_spi_irq() and
dereference already-freed memory.
Switch to devm_spi_alloc_host() so that the devres LIFO order releases
the controller only after free_irq() has drained the handler, and drop
the now-redundant spi_controller_put() from .remove(). The probe error
path is simplified to direct returns.
The clock is acquired with devm_clk_get_enabled(), which is registered
after the IRQ and thus released before it by the devres LIFO order.
Drain the interrupt explicitly with devm_free_irq() before disabling the
controller so that a late interrupt cannot access the registers of a
clock-gated controller.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix overreads in ath11k_wmi_process_csa_switch_count_event()
There is no policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT, so
the parse infrastructure does not enforce a minimum length for the event
struct. Additionally, the num_vdevs field is taken directly from firmware
and used as a loop bound over the vdev_ids array without checking that it
fits within the TLV payload. Either condition can cause an out-of-bounds
read.
Add a TLV policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT so
the parse infrastructure enforces a minimum length for the fixed-size event
struct. Add a helper ath11k_wmi_tlv_data_len() to recover the payload
length of a parsed TLV from the header preceding its data pointer. Use it
in ath11k_wmi_process_csa_switch_count_event() to bound num_vdevs before
the loop.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix stride mismatch in mac_phy_caps_parse()
Currently, in ath11k_wmi_tlv_mac_phy_caps_parse(), kcalloc() sizes the
mac_phy_caps buffer as tot_phy_id * len, where len is clamped to
min(firmware_len, sizeof(struct wmi_mac_phy_capabilities)). The subsequent
memcpy() destination advances by sizeof(full struct) per slot via C
pointer arithmetic, not by the clamped len. When firmware sends short
TLVs, the second and later slots are written past the end of the
allocation.
The reader in ath11k_pull_mac_phy_cap_svc_ready_ext() also indexes the
buffer with full-struct pointer arithmetic, so the allocation must match
that stride.
Fix by using kzalloc_objs(), which derives the element size from the
pointer type, making allocation size and pointer stride provably
consistent regardless of what len the firmware provides.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix potential UAF when reading bpf link info
In bpf_link_show_fdinfo and bpf_link_get_info_by_fd, link->prog is
accessed without holding any locks. If the prog is concurrently replaced
via bpf_link_update, the old prog can be freed, leading to a potential
UAF issue.
Fix this by accessing link->prog under RCU protection to safely fetch
the pointer and guarantee its lifetime while reading its fields. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: create serial pool adding rdev to array with serialize_policy=1
The following bug has been observed with kernel 7.1.3 after adding a new
rdev to an existing RAID1 array with serialize_policy enabled:
Oops: 0002 [#1]
CPU: 0 UID: 0 PID: 19639 Comm: ext4lazyinit Not tainted 7.1.3-1-default
RIP: _raw_spin_lock_irqsave+0x27/0x50
CR2: 0000000000004960
Call Trace:
wait_for_serialization+0xb9/0x260 [raid1]
raid1_make_request+0x762/0xaff [raid1]
md_handle_request+0x1c9/0x2e0 [md_mod]
The raid1.c code calls wait_for_serialization() if the MD_SERIALIZE_POLICY
is set, and wait_for_serialization assumes that rdev->serial is
initialized. Normally this will be the case for arrays that have
the serialize_policy sysfs attribute set to 1.
But when a new rdev is added to an existing array in bind_rdev_to_array(),
the condition at mddev_create_serial_pool() causes creation of rdev->serial
to be skipped. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: sgi-gru: remove interrupt-context page-table walks
The GRU TLB miss handler walks a process's page tables without holding
page-table locks or a reference to the mapped page. It also uses a kernel
page-table accessor on user page tables and supports only PMD-level large
mappings on x86-64.
Remove the direct walker. Send interrupt faults directly to user polling
mode so the existing call-OS fallback retries them in process context.
Remove the mmap-lock failure statistic that can no longer be incremented. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix non-AQL packet accounting for MLO stations
__mt76_tx_queue_skb() overrides the wcid passed by the driver with
sta->drv_priv, so the wcid might incorrectly be changed after TX,
causing wcid->non_aql_packets to be counted on the wrong wcid. For
example, on the AP side, if a station's setup link is the 5G link and
the station uses 2G to transmit a frame, the value of non_aql_packets
is increased on the 5G wcid but decreased on the 2G wcid. Once the
inflated counter exceeds MT_MAX_NON_AQL_PKT, the TX scheduler
permanently refuses to service the station.
Drop the reassignment and account on the wcid used for transmission.
This also records the actual wcid in the queue entry. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: unwind state on add_interface failure
When mt76_wcid_alloc() fails, mt7915_add_interface() returned without
clearing the vif_mask/omac_mask bits it had already set, without removing
the firmware dev info added earlier, and without clearing a monitor_vif
pointer to the vif mac80211 is about to free. mac80211 does not call
remove_interface() for a failed add, so the indices and firmware dev
entry leaked permanently and testmode could dereference the stale
monitor_vif. Add a proper error unwind. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: cancel reset and rc work on device unregister
Both drivers cancelled dump_work on unregister but left reset_work and
rc_work to be flushed only by destroy_workqueue() in mt76_free_device(),
which runs after the hw is unregistered and the hardware stopped. A
reset_work that fires in that window calls ieee80211_restart_hw() and
re-arms mac_work on an unregistered hw, and rc_work touches station state
being torn down. Cancel both up front, alongside dump_work. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, x86: Fix trampoline stack size for 128-bit arguments
btf_distill_func_proto() accepts a function argument up to 16 bytes, so a
128-bit scalar such as __int128 reaches the x86 trampoline with
arg_size == 16. But the current implementation assumes an __int128
argument only needs one register, so the register save area is
under-allocated and save_args() overwrites adjacent stack slots.
Compute the register count from arg_size for all arguments to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core seccomp code, instead move the
synchronisation code into the ptrace GPR and syscall setting code so
that 'orig_x0' is kept up to date with x0 whenever we're stopped on the
syscall entry path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: clean up color-change beacon data on errors
nl80211_color_change() calls nl80211_parse_beacon() for the beacon_next
template, which can allocate params.beacon_next.mbssid_ies and .rnr_ies.
A parsing failure returned directly instead of using the out: cleanup,
leaking any allocations completed before the error.
Allocate the nested attribute table before parsing beacon_next. Its
allocation failure can then return before beacon data exists, while a
later parsing failure uses out: to release the parsed data. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix P2P action frame handling without device vif
Some P2P action frame paths assume the P2P device vif is always
available. That is not true when userspace sends non-P2P public action
frames through the primary interface, or when action-frame abort runs
after the P2P device vif has not been created.
Fall back to the primary vif when aborting an action frame without a P2P
device vif, and guard P2P device saved IE access before using it for
peer channel search. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: stop PMSR before P2P and NAN teardown
PMSR request teardown must abort active measurements while the
wireless_dev is still present in the driver. cfg80211_leave_locked() and
cfg80211_stop_pd() already do this before invoking the driver's stop
callback, but cfg80211_stop_p2p_device() and cfg80211_stop_nan() do not.
Those helpers are also called directly by nl80211, rfkill shutdown, and
wireless_dev unregister paths. If one of these paths stops a P2P device
or NAN interface with a pending request, it removes the mac80211
subinterface from the driver first. Subsequent request cleanup cannot
reach the lower driver's abort callback, but cfg80211 frees the request
regardless. Driver state can then retain a stale request and use it when
it later reports a result.
Call cfg80211_pmsr_wdev_down() before stopping the P2P device or NAN
interface. This keeps lower-driver request state and cfg80211 request
ownership in sync for all of the helpers' callers. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: core: do fallible allocations before the console can be registered
serial_core_add_one_port() allocates uport->tty_groups after
uart_configure_port(), which may register the console. If the allocation
fails, the driver unwinds the port while its console remains registered.
The earlier uport->name allocation has a related failure path that leaves
state->uart_port linked to a port being freed.
Failslab reproduced a NULL dereference in PL011 console output and a KASAN
use-after-free in i.MX console output after failed binds.
Allocate the name and tty_groups before linking the port and configuring
it. Reserve space for the optional driver attribute group because
config_port() may populate uport->attr_group during configuration. |
