| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: hold the RCU lock across ipv6_chk_addr() in rds_tcp_laddr_check()
rds_tcp_laddr_check() looks up a scoped IPv6 interface with
dev_get_by_index_rcu(), drops the RCU read-side lock, and only then
passes the bare struct net_device * into ipv6_chk_addr().
dev_get_by_index_rcu() only keeps the device alive within the same RCU
read-side section. After rcu_read_unlock(), a concurrent RTM_DELLINK can
free the net_device; ipv6_chk_addr() then dereferences the stale pointer
in __ipv6_chk_addr_and_flags() (e.g. l3mdev_master_dev_rcu(dev)), reading
freed memory.
Keep the RCU read-side lock held across the ipv6_chk_addr() call instead
of dropping it right after the lookup, so the device cannot be freed
while it is in use.
BUG: KASAN: slab-use-after-free in __ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
Read of size 8 at addr ffff8880106ec000 by task exploit/153
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
__ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
ipv6_chk_addr (net/ipv6/addrconf.c:2031 net/ipv6/addrconf.c:1972)
rds_tcp_laddr_check (net/rds/tcp.c:370)
rds_bind (net/rds/bind.c:248)
__sys_bind (net/socket.c:1920)
__x64_sys_bind (net/socket.c:1956)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) |
| Use after free in Browser in Google Chrome on on Mac prior to 151.0.7922.169 allowed a remote attacker leveraging social engineering to execute arbitrary code outside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| Use after free in WebGL in Google Chrome prior to 151.0.7922.169 allowed a remote attacker to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: High) |
| X.509IF protocol dissector crash in 4.6.0 to 4.6.7 and 4.4.0 to 4.4.18 allows denial of service |
| Crash in sharkd in 4.6.0 to 4.6.7 and 4.4.0 to 4.4.18 allows denial of service |
| Crash in sharkd in 4.6.0 to 4.6.7 and 4.4.0 to 4.4.18 allows denial of service |
| Use-after-free in the Layout: Text and Fonts component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: fix potential use-after-free in audit_del_rule()
`audit_del_rule()` destroys `e->rule.exe` via `audit_remove_mark_rule()`
before unlinking the rule from RCU-visible filter lists and waiting for a
grace period. Concurrent readers in `audit_filter()` and
`audit_filter_rules()` still dereference `e->rule.exe`, while the fsnotify
mark can be freed on an independent lifetime path. This creates a
use-after-free window during rule deletion.
Fix this by unlinking the rule from the RCU-visible lists and invoking
`synchronize_rcu()` before calling `audit_remove_mark_rule()` (and other
rule removal helpers). This ensures that all existing RCU readers have
exited the critical section before any underlying resources are destroyed. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix socket use-after-free during link group termination
__smc_lgr_terminate() drops conns_lock after finding a connection in
lgr->conns_all, but before taking a reference on its socket. The connection
is embedded in the socket, and its registration reference protects it only
while the connection remains in the tree.
A concurrent close can unregister the connection and drop that reference,
freeing the socket before the termination worker reaches sock_hold().
The race is reachable when close overlaps link group termination.
Local stress testing reproduced the use-after-free and KASAN reported:
BUG: KASAN: slab-use-after-free in __smc_lgr_terminate.part.0 [smc]
Write of size 4 by task kworker/3:3
Workqueue: events smc_lgr_terminate_work [smc]
__smc_lgr_terminate.part.0 [smc]
The socket was allocated by smc_create(), freed through
slab_free_after_rcu_debug(), and was followed by:
refcount_t: addition on 0; use-after-free.
__smc_lgr_terminate.part.0 [smc]
Take the socket reference while conns_lock still protects the tree entry.
The unregister path then cannot drop the last reference until termination
has finished using the socket. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: unlock i_mmap_rwsem before releasing after-split folios
__folio_split() keeps dereferencing the mapping after the split:
shmem_uncharge(mapping->host) and remap_page() while the folios are still
frozen/locked, and i_mmap_unlock_read(mapping) at the very end, after the
after-split folios have been unlocked and freed.
Nothing holds an inode reference across that. The split relies on @folio
-- which the beyond-EOF drop loop never removes, as it starts at
folio_next(folio) -- staying locked and in the page cache to hold off
eviction. But the unlock loop unlocks @folio before i_mmap_unlock_read()
runs. If the caller's @lock_at is a tail beyond EOF, as memory_failure()
passes when splitting a poisoned tail of a shmem THP that reaches past
i_size during truncation, it too is gone from the page cache; so once
@folio is unlocked no locked, in-cache folio pins the inode, and a
concurrent final iput() can evict and RCU-free it before
i_mmap_unlock_read() touches i_mmap_rwsem:
BUG: KASAN: slab-use-after-free in __up_read+0x634/0x790
i_mmap_unlock_read include/linux/fs.h:537 [inline]
__folio_split+0x732/0x1640 mm/huge_memory.c:4100
try_to_split_thp_page+0xab/0x390 mm/memory-failure.c:1675
memory_failure+0x1394/0x26e0 mm/memory-failure.c:2470
Freed by task 4601:
shmem_free_in_core_inode+0x54/0xb0 mm/shmem.c:5177
evict+0x57f/0xac0 fs/inode.c:870
Do every mapping dereference while @folio still pins the inode: drop
i_mmap_rwsem right after remap_page(), before the loop that unlocks and
frees the after-split folios, and clear @mapping so the exit path does not
unlock it again. shmem_uncharge() and remap_page() already run before
that point, so after this nothing past the unlock loop touches the inode
or the mapping.
This is now a rule the split depends on, alongside keeping @folio frozen
until the page cache is updated: no inode or mapping dereference once the
after-split folios start being unlocked. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix potential UAF on meter attach failure
While attaching a newly created meter attach_meter() function makes
the new meter visible to other CPUs but can still fail afterwards.
On failure, it detaches the meter back and returns an error.
However, this is an unexpected behavior for the ovs_meter_cmd_set()
that uses a plain kfree(meter) on attach failure without waiting for
RCU readers to stop using it, assuming it was never visible.
This is never a problem for ovs-vswitchd as it always creates meters
before creating any flows that use them. But the UAF can be triggered
with a custom application using uAPI:
BUG: KASAN: slab-use-after-free in ovs_meter_execute (net/openvswitch/meter.c:653)
Read of size 8 at addr ffff88810d152650 by task meter/2508
Call Trace:
ovs_meter_execute (net/openvswitch/meter.c:653)
do_execute_actions (net/openvswitch/actions.c:1407)
ovs_execute_actions (net/openvswitch/actions.c:1584)
ovs_packet_cmd_execute (net/openvswitch/datapath.c:703)
...
netlink_sendmsg (af_netlink.c:1900)
Allocated by task 2519:
__kasan_kmalloc (mm/kasan/common.c:398 mm/kasan/common.c:415)
ovs_meter_cmd_set (net/openvswitch/meter.c:422)
...
netlink_sendmsg (af_netlink.c:1900)
Freed by task 2519:
kfree (mm/slub.c:2705 mm/slub.c:6405 mm/slub.c:6720)
ovs_meter_cmd_set (net/openvswitch/meter.c:479)
...
netlink_sendmsg (af_netlink.c:1900)
Fix that by making sure attach_meter() doesn't make the meter visible
until all the checks are done and the function can't fail anymore.
This also makes sure the "hash" value is calculated after the potential
re-sizing of the table.
Reported by Trend Micro's Zero Day Initiative as ZDI-CAN-31642. |
| Race condition, use-after-free in the Graphics component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Check return value of __register_event() in trace_module_add_events()
trace_module_add_events() ignores the return value of __register_event()
and unconditionally calls __add_event_to_tracers() for each event.
If __register_event() fails (for example, if event_init() fails), the
trace_event_call is not added to ftrace_events list, but
__add_event_to_tracers() still creates a trace_event_file pointing to it.
If module loading subsequently fails and module memory is freed, tracing
state retains a stale trace_event_call pointer in trace_event_file,
leading to a use-after-free when tracefs or tracing subsystem operations
are later executed.
Fix this by checking the return value of __register_event() and only
calling __add_event_to_tracers() if event registration succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: fix use-after-free race with concurrent NETDEV_UNREGISTER
isotp_release() looked up the bound network device via dev_get_by_index()
using the stored ifindex. During device unregistration the device is
unlisted from the ifindex hash before the NETDEV_UNREGISTER notifier
chain runs, so a concurrent isotp_release() could find no device, skip
can_rx_unregister() entirely, and still proceed to free the socket.
Since isotp_release() had already removed itself from the isotp
notifier list at that point, isotp_notify() would never get a chance to
clean up either, leaving a stale CAN filter that keeps pointing at the
freed socket.
Fix this the same way raw.c already does: hold a tracked reference to
the bound net_device in the socket (so->dev/so->dev_tracker) from
bind() onward instead of re-resolving it from the ifindex, and
serialize bind()/release() with rtnl_lock() so that so->dev is always
consistent with what the NETDEV_UNREGISTER notifier sees. so->dev
stays valid regardless of ifindex-hash unlisting, and is only ever
cleared by whichever of isotp_release()/isotp_notify() gets there
first, so the filter is always removed exactly once.
isotp_bind() now rejects a (re)bind with -EAGAIN while so->[tx|rx].state
isn't ISOTP_IDLE yet, so a timer left running by a prior
NETDEV_UNREGISTER can't act on a newly bound so->ifindex. Both checks
share the same lock_sock() section, so there is no window in which a
concurrent isotp_notify() clearing so->bound could be missed. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add missing device refcount for CAN filter removal
sashiko-bot remarked a problem with a concurrent device unregistration
in isotp.c which also is present in the bcm.c code. A former fix for raw.c
commit c275a176e4b6 ("can: raw: add missing refcount for memory leak fix")
introduced a netdevice_tracker which solves the issue for bcm.c too.
bcm_release(), bcm_delete_rx_op() and bcm_notifier() relied on
dev_get_by_index(ifindex) to re-find the device for an rx_op before
unregistering its filter. If a concurrent NETDEV_UNREGISTER has already
unlisted the device from the ifindex table, that lookup fails and
can_rx_unregister() is silently skipped, leaving a stale CAN filter
pointing at the soon-to-be-freed bcm_op/socket.
Hold a netdev_hold()/netdev_put() tracked reference on op->rx_reg_dev
from the moment the rx filter is registered in bcm_rx_setup() until it
is unregistered in bcm_rx_unreg(), and use that reference directly in
bcm_release() and bcm_delete_rx_op() instead of re-looking the device
up by ifindex. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Fix use-after-free on vendor module reload
mmu_destroy_caches() destroys pte_list_desc_cache and
mmu_page_header_cache, but leaves both pointers unchanged. The pointers
live in kvm.ko, and therefore survive when a vendor module is unloaded
while kvm.ko remains loaded.
If creation of pte_list_desc_cache fails during a subsequent vendor
module load, its assignment sets pte_list_desc_cache to NULL and the
error path calls mmu_destroy_caches(). mmu_page_header_cache still
points to the cache destroyed during the preceding vendor module
unload. Passing that stale pointer to kmem_cache_destroy() causes a
slab use-after-free.
Reproduce the issue on a v7.1.3 kernel with CONFIG_KASAN=y,
CONFIG_KASAN_GENERIC=y, CONFIG_KVM=m, and CONFIG_KVM_INTEL=m. A
one-shot test hook forces pte_list_desc_cache to NULL on the second
invocation of kvm_mmu_vendor_module_init():
1. Load kvm.ko and kvm-intel.ko, creating both caches.
2. Unload only kvm_intel, leaving kvm.ko loaded.
3. Reload kvm_intel and force initialization through the -ENOMEM path.
KASAN reports:
BUG: KASAN: slab-use-after-free in
kvm_mmu_vendor_module_init+0x5b/0x170 [kvm]
...
kmem_cache_destroy+0x21/0x1d0
kvm_mmu_vendor_module_init+0x5b/0x170 [kvm]
...
Allocated by task 16817:
__kmem_cache_create_args+0x12c/0x3b0
__kmem_cache_create.constprop.0+0xb6/0xf0 [kvm]
kvm_mmu_vendor_module_init+0x13b/0x170 [kvm]
...
Freed by task 16820:
kmem_cache_destroy+0x117/0x1d0
kvm_mmu_vendor_module_exit+0x21/0x30 [kvm]
Clear both pointers immediately after destroying their caches so that
the stored state reflects the caches' lifetime and repeated cleanup is
safe.
With the fix applied, the same injected vendor module reload fails with
-ENOMEM as expected and produces no KASAN report. |
| In the Linux kernel, the following vulnerability has been resolved:
gpu: host1x: Fix use-after-free in host1x_bo_clear_cached_mappings
__host1x_bo_unpin() drops the last reference to the mapping and frees
it, so we can't dereference mapping afterwards. The cache itself
outlives the mapping, so use the cache local variable instead. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: cancel sched scan results work on unregister
cfg80211_sched_scan_results() can queue rdev->sched_scan_res_wk from a
driver result notification while a scheduled scan request is present. The
work callback recovers the containing cfg80211_registered_device and then
locks the wiphy and walks the scheduled-scan request list.
wiphy_unregister() already makes the wiphy unreachable and drains rdev work
items before cfg80211_dev_free() can release the object, but it does not
drain sched_scan_res_wk. A queued or running result work item can therefore
cross the unregister/free boundary and access freed rdev state.
The buggy scenario involves two paths, with each column showing the order
within that path:
scheduled-scan result path: unregister/free path:
1. cfg80211_sched_scan_results() 1. interface teardown stops and
queues rdev->sched_scan_res_wk. removes the scheduled scan request.
2. cfg80211_wq starts the work 2. wiphy_unregister() drains other
item and recovers rdev. rdev work items.
3. The worker locks rdev->wiphy 3. cfg80211_dev_free() destroys and
and walks rdev state. frees rdev.
Cancel sched_scan_res_wk in wiphy_unregister() alongside the other rdev
work items. cancel_work_sync() removes a pending result notification and
waits for an already running callback, so cfg80211_dev_free() cannot free
rdev while this work item is still active.
Validation reproduced this kernel report:
BUG: KASAN: use-after-free in cfg80211_sched_scan_results_wk+0x4a6/0x530
Workqueue: cfg80211 cfg80211_sched_scan_results_wk [cfg80211]
Read of size 8
Call trace:
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x630
cfg80211_sched_scan_results_wk+0x4a6/0x530
srso_alias_return_thunk+0x5/0xfbef5
__virt_addr_valid+0x224/0x430
kasan_report+0xac/0xe0
lockdep_hardirqs_on_prepare+0xea/0x1a0
process_one_work+0x8d0/0x18f0 (kernel/workqueue.c:3212)
lock_is_held_type+0x8f/0x100
worker_thread+0x5ad/0xfd0
__kthread_parkme+0xc6/0x200
kthread+0x31e/0x410
trace_hardirqs_on+0x1a/0x170
ret_from_fork+0x576/0x810
__switch_to+0x57e/0xe20
__switch_to_asm+0x33/0x70
ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
ppp: defer channel free to an RCU grace period to fix pppol2tp RX UAF
pppol2tp_recv() runs in the L2TP UDP-encap softirq RX path:
l2tp_udp_encap_recv() -> l2tp_recv_common() -> pppol2tp_recv()
-> ppp_input(&po->chan)
It runs under rcu_read_lock() holding only an l2tp_session reference and
takes NO reference on the internal PPP channel (struct channel,
chan->ppp) that ppp_input() dereferences.
The pppox socket is SOCK_RCU_FREE, so 'po' and the embedded ppp_channel
are RCU-safe. But the internal struct channel is a separate allocation
that ppp_release_channel() frees with a plain kfree():
close(data socket) -> pppol2tp_release() -> pppox_unbind_sock()
-> ppp_unregister_channel() -> ppp_release_channel() -> kfree(pch)
For a channel that is bound (PPPIOCGCHAN) but not attached to a ppp unit
(no PPPIOCCONNECT, pch->ppp == NULL) and not bridged, teardown skips
both ppp_disconnect_channel()'s synchronize_net() and
ppp_unbridge_channels()'s synchronize_rcu(), so the kfree() has no grace
period. rcu_read_lock() in pppol2tp_recv() does not protect against a
plain kfree(), so an in-flight ppp_input() on one CPU can dereference
the channel just freed by close() on another CPU.
The bug is reachable by an unprivileged user.
Defer the channel free to an RCU callback via call_rcu() so the grace
period fences any in-flight ppp_input(). The disconnect and unbridge
teardown paths already fence with synchronize_net()/synchronize_rcu();
call_rcu() does the same here without stalling the close() path. |
| In the Linux kernel, the following vulnerability has been resolved:
net/iucv: take a reference on the socket found in afiucv_hs_rcv()
afiucv_hs_rcv() looks up the destination socket under iucv_sk_list.lock,
drops the lock, and then passes the socket to the afiucv_hs_callback_*()
handlers without holding a reference. AF_IUCV sockets are not
RCU-protected and are freed synchronously by iucv_sock_kill() ->
sock_put(), so a concurrent close can free the socket in the window
between read_unlock() and the handler, which then dereferences freed
memory (for example sk->sk_data_ready() in afiucv_hs_callback_syn()).
Take a reference with sock_hold() while the socket is still on the list
and release it with sock_put() once the handler has run. |
