| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
x86/vmware: Fix hypercall clobbers
Fedora QA reported the following panic:
BUG: unable to handle page fault for address: 0000000040003e54
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20251119-3.fc43 11/19/2025
RIP: 0010:vmware_hypercall4.constprop.0+0x52/0x90
..
Call Trace:
vmmouse_report_events+0x13e/0x1b0
psmouse_handle_byte+0x15/0x60
ps2_interrupt+0x8a/0xd0
...
because the QEMU VMware mouse emulation is buggy, and clears the top 32
bits of %rdi that the kernel kept a pointer in.
The QEMU vmmouse driver saves and restores the register state in a
"uint32_t data[6];" and as a result restores the state with the high
bits all cleared.
RDI originally contained the value of a valid kernel stack address
(0xff5eeb3240003e54). After the vmware hypercall it now contains
0x40003e54, and we get a page fault as a result when it is dereferenced.
The proper fix would be in QEMU, but this works around the issue in the
kernel to keep old setups working, when old kernels had not happened to
keep any state in %rdi over the hypercall.
In theory this same issue exists for all the hypercalls in the vmmouse
driver; in practice it has only been seen with vmware_hypercall3() and
vmware_hypercall4(). For now, just mark RDI/RSI as clobbered for those
two calls. This should have a minimal effect on code generation overall
as it should be rare for the compiler to want to make RDI/RSI live
across hypercalls. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Fix use-after-free in iscsit_dec_conn_usage_count()
In iscsit_dec_conn_usage_count(), the function calls complete() while
holding the conn->conn_usage_lock. As soon as complete() is invoked, the
waiter (such as iscsit_close_connection()) may wake up and proceed to free
the iscsit_conn structure.
If the waiter frees the memory before the current thread reaches
spin_unlock_bh(), it results in a KASAN slab-use-after-free as the function
attempts to release a lock within the already-freed connection structure.
Fix this by releasing the spinlock before calling complete(). |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: loongson-64bit: Fix incorrect NULL check after devm_kcalloc()
Fix incorrect NULL check in loongson_gpio_init_irqchip().
The function checks chip->parent instead of chip->irq.parents. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/slab: Add alloc_tagging_slab_free_hook for memcg_alloc_abort_single
When CONFIG_MEM_ALLOC_PROFILING_DEBUG is enabled, the following warning
may be noticed:
[ 3959.023862] ------------[ cut here ]------------
[ 3959.023891] alloc_tag was not cleared (got tag for lib/xarray.c:378)
[ 3959.023947] WARNING: ./include/linux/alloc_tag.h:155 at alloc_tag_add+0x128/0x178, CPU#6: mkfs.ntfs/113998
[ 3959.023978] Modules linked in: dns_resolver tun brd overlay exfat btrfs blake2b libblake2b xor xor_neon raid6_pq loop sctp ip6_udp_tunnel udp_tunnel ext4 crc16 mbcache jbd2 rfkill sunrpc vfat fat sg fuse nfnetlink sr_mod virtio_gpu cdrom drm_client_lib virtio_dma_buf drm_shmem_helper drm_kms_helper ghash_ce drm sm4 backlight virtio_net net_failover virtio_scsi failover virtio_console virtio_blk virtio_mmio dm_mirror dm_region_hash dm_log dm_multipath dm_mod i2c_dev aes_neon_bs aes_ce_blk [last unloaded: hwpoison_inject]
[ 3959.024170] CPU: 6 UID: 0 PID: 113998 Comm: mkfs.ntfs Kdump: loaded Tainted: G W 6.19.0-rc7+ #7 PREEMPT(voluntary)
[ 3959.024182] Tainted: [W]=WARN
[ 3959.024186] Hardware name: QEMU KVM Virtual Machine, BIOS unknown 2/2/2022
[ 3959.024192] pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 3959.024199] pc : alloc_tag_add+0x128/0x178
[ 3959.024207] lr : alloc_tag_add+0x128/0x178
[ 3959.024214] sp : ffff80008b696d60
[ 3959.024219] x29: ffff80008b696d60 x28: 0000000000000000 x27: 0000000000000240
[ 3959.024232] x26: 0000000000000000 x25: 0000000000000240 x24: ffff800085d17860
[ 3959.024245] x23: 0000000000402800 x22: ffff0000c0012dc0 x21: 00000000000002d0
[ 3959.024257] x20: ffff0000e6ef3318 x19: ffff800085ae0410 x18: 0000000000000000
[ 3959.024269] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 3959.024281] x14: 0000000000000000 x13: 0000000000000001 x12: ffff600064101293
[ 3959.024292] x11: 1fffe00064101292 x10: ffff600064101292 x9 : dfff800000000000
[ 3959.024305] x8 : 00009fff9befed6e x7 : ffff000320809493 x6 : 0000000000000001
[ 3959.024316] x5 : ffff000320809490 x4 : ffff600064101293 x3 : ffff800080691838
[ 3959.024328] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff0000d5bcd640
[ 3959.024340] Call trace:
[ 3959.024346] alloc_tag_add+0x128/0x178 (P)
[ 3959.024355] __alloc_tagging_slab_alloc_hook+0x11c/0x1a8
[ 3959.024362] kmem_cache_alloc_lru_noprof+0x1b8/0x5e8
[ 3959.024369] xas_alloc+0x304/0x4f0
[ 3959.024381] xas_create+0x1e0/0x4a0
[ 3959.024388] xas_store+0x68/0xda8
[ 3959.024395] __filemap_add_folio+0x5b0/0xbd8
[ 3959.024409] filemap_add_folio+0x16c/0x7e0
[ 3959.024416] __filemap_get_folio_mpol+0x2dc/0x9e8
[ 3959.024424] iomap_get_folio+0xfc/0x180
[ 3959.024435] __iomap_get_folio+0x2f8/0x4b8
[ 3959.024441] iomap_write_begin+0x198/0xc18
[ 3959.024448] iomap_write_iter+0x2ec/0x8f8
[ 3959.024454] iomap_file_buffered_write+0x19c/0x290
[ 3959.024461] blkdev_write_iter+0x38c/0x978
[ 3959.024470] vfs_write+0x4d4/0x928
[ 3959.024482] ksys_write+0xfc/0x1f8
[ 3959.024489] __arm64_sys_write+0x74/0xb0
[ 3959.024496] invoke_syscall+0xd4/0x258
[ 3959.024507] el0_svc_common.constprop.0+0xb4/0x240
[ 3959.024514] do_el0_svc+0x48/0x68
[ 3959.024520] el0_svc+0x40/0xf8
[ 3959.024526] el0t_64_sync_handler+0xa0/0xe8
[ 3959.024533] el0t_64_sync+0x1ac/0x1b0
[ 3959.024540] ---[ end trace 0000000000000000 ]---
When __memcg_slab_post_alloc_hook() fails, there are two different
free paths depending on whether size == 1 or size != 1. In the
kmem_cache_free_bulk() path, we do call alloc_tagging_slab_free_hook().
However, in memcg_alloc_abort_single() we don't, the above warning will be
triggered on the next allocation.
Therefore, add alloc_tagging_slab_free_hook() to the
memcg_alloc_abort_single() path. |
| Integer overflow in Skia in Google Chrome prior to 145.0.7632.159 allowed a remote attacker to potentially perform out of bounds memory access via a crafted HTML page. (Chromium security severity: Critical) |
| Object lifecycle issue in DevTools in Google Chrome prior to 145.0.7632.159 allowed an attacker who convinced a user to install a malicious extension to potentially exploit heap corruption via a crafted Chrome Extension. (Chromium security severity: High) |
| Unauthorized report deletion due to insufficient access control. The following products are affected: Acronis Cyber Protect 17 (Linux, Windows) before build 41186. |
| Unauthorized data access due to insufficient access control validation. The following products are affected: Acronis Cyber Protect 17 (Linux, Windows) before build 41186. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_log: fix uninitialized padding leak in NFULA_PAYLOAD
__build_packet_message() manually constructs the NFULA_PAYLOAD netlink
attribute using skb_put() and skb_copy_bits(), bypassing the standard
nla_reserve()/nla_put() helpers. While nla_total_size(data_len) bytes
are allocated (including NLA alignment padding), only data_len bytes
of actual packet data are copied. The trailing nla_padlen(data_len)
bytes (1-3 when data_len is not 4-byte aligned) are never initialized,
leaking stale heap contents to userspace via the NFLOG netlink socket.
Replace the manual attribute construction with nla_reserve(), which
handles the tailroom check, header setup, and padding zeroing via
__nla_reserve(). The subsequent skb_copy_bits() fills in the payload
data on top of the properly initialized attribute. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_sip: fix use of uninitialized rtp_addr in process_sdp
process_sdp() declares union nf_inet_addr rtp_addr on the stack and
passes it to the nf_nat_sip sdp_session hook after walking the SDP
media descriptions. However rtp_addr is only initialized inside the
media loop when a recognized media type with a non-zero port is found.
If the SDP body contains no m= lines, only inactive media sections
(m=audio 0 ...) or only unrecognized media types, rtp_addr is never
assigned. Despite that, the function still calls hooks->sdp_session()
with &rtp_addr, causing nf_nat_sdp_session() to format the stale stack
value as an IP address and rewrite the SDP session owner and connection
lines with it.
With CONFIG_INIT_STACK_ALL_ZERO (default on most distributions) this
results in the session-level o= and c= addresses being rewritten to
0.0.0.0 for inactive SDP sessions. Without stack auto-init the
rewritten address is whatever happened to be on the stack.
Fix this by pre-initializing rtp_addr from the session-level connection
address (caddr) when available, and tracking via a have_rtp_addr flag
whether any valid address was established. Skip the sdp_session hook
entirely when no valid address exists. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: ib: reject FRMR registration before IB connection is established
rds_ib_get_mr() extracts the rds_ib_connection from conn->c_transport_data
and passes it to rds_ib_reg_frmr() for FRWR memory registration. On a
fresh outgoing connection, ic is allocated in rds_ib_conn_alloc() with
i_cm_id = NULL because the connection worker has not yet called
rds_ib_conn_path_connect() to create the rdma_cm_id. When sendmsg() with
RDS_CMSG_RDMA_MAP is called on such a connection, the sendmsg path parses
the control message before any connection establishment, allowing
rds_ib_post_reg_frmr() to dereference ic->i_cm_id->qp and crash the
kernel.
The existing guard in rds_ib_reg_frmr() only checks for !ic (added in
commit 9e630bcb7701), which does not catch this case since ic is allocated
early and is always non-NULL once the connection object exists.
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:rds_ib_post_reg_frmr+0x50e/0x920
Call Trace:
rds_ib_post_reg_frmr (net/rds/ib_frmr.c:167)
rds_ib_map_frmr (net/rds/ib_frmr.c:252)
rds_ib_reg_frmr (net/rds/ib_frmr.c:430)
rds_ib_get_mr (net/rds/ib_rdma.c:615)
__rds_rdma_map (net/rds/rdma.c:295)
rds_cmsg_rdma_map (net/rds/rdma.c:860)
rds_sendmsg (net/rds/send.c:1363)
____sys_sendmsg
do_syscall_64
Add a check in rds_ib_get_mr() that verifies ic, i_cm_id, and qp are all
non-NULL before proceeding with FRMR registration, mirroring the guard
already present in rds_ib_post_inv(). Return -ENODEV when the connection
is not ready, which the existing error handling in rds_cmsg_send() converts
to -EAGAIN for userspace retry and triggers rds_conn_connect_if_down() to
start the connection worker. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: x_tables: restrict xt_check_match/xt_check_target extensions for NFPROTO_ARP
Weiming Shi says:
xt_match and xt_target structs registered with NFPROTO_UNSPEC can be
loaded by any protocol family through nft_compat. When such a
match/target sets .hooks to restrict which hooks it may run on, the
bitmask uses NF_INET_* constants. This is only correct for families
whose hook layout matches NF_INET_*: IPv4, IPv6, INET, and bridge
all share the same five hooks (PRE_ROUTING ... POST_ROUTING).
ARP only has three hooks (IN=0, OUT=1, FORWARD=2) with different
semantics. Because NF_ARP_OUT == 1 == NF_INET_LOCAL_IN, the .hooks
validation silently passes for the wrong reasons, allowing matches to
run on ARP chains where the hook assumptions (e.g. state->in being
set on input hooks) do not hold. This leads to NULL pointer
dereferences; xt_devgroup is one concrete example:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000044: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000220-0x0000000000000227]
RIP: 0010:devgroup_mt+0xff/0x350
Call Trace:
<TASK>
nft_match_eval (net/netfilter/nft_compat.c:407)
nft_do_chain (net/netfilter/nf_tables_core.c:285)
nft_do_chain_arp (net/netfilter/nft_chain_filter.c:61)
nf_hook_slow (net/netfilter/core.c:623)
arp_xmit (net/ipv4/arp.c:666)
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
Fix it by restricting arptables to NFPROTO_ARP extensions only.
Note that arptables-legacy only supports:
- arpt_CLASSIFY
- arpt_mangle
- arpt_MARK
that provide explicit NFPROTO_ARP match/target declarations. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_hfsc: fix divide-by-zero in rtsc_min()
m2sm() converts a u32 slope to a u64 scaled value. For large inputs
(e.g. m1=4000000000), the result can reach 2^32. rtsc_min() stores
the difference of two such u64 values in a u32 variable `dsm` and
uses it as a divisor. When the difference is exactly 2^32 the
truncation yields zero, causing a divide-by-zero oops in the
concave-curve intersection path:
Oops: divide error: 0000
RIP: 0010:rtsc_min (net/sched/sch_hfsc.c:601)
Call Trace:
init_ed (net/sched/sch_hfsc.c:629)
hfsc_enqueue (net/sched/sch_hfsc.c:1569)
[...]
Widen `dsm` to u64 and replace do_div() with div64_u64() so the full
difference is preserved. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_flow: fix NULL pointer dereference on shared blocks
flow_change() calls tcf_block_q() and dereferences q->handle to derive
a default baseclass. Shared blocks leave block->q NULL, causing a NULL
deref when a flow filter without a fully qualified baseclass is created
on a shared block.
Check tcf_block_shared() before accessing block->q and return -EINVAL
for shared blocks. This avoids the null-deref shown below:
=======================================================================
KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f]
RIP: 0010:flow_change (net/sched/cls_flow.c:508)
Call Trace:
tc_new_tfilter (net/sched/cls_api.c:2432)
rtnetlink_rcv_msg (net/core/rtnetlink.c:6980)
[...]
======================================================================= |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_fw: fix NULL pointer dereference on shared blocks
The old-method path in fw_classify() calls tcf_block_q() and
dereferences q->handle. Shared blocks leave block->q NULL, causing a
NULL deref when an empty cls_fw filter is attached to a shared block
and a packet with a nonzero major skb mark is classified.
Reject the configuration in fw_change() when the old method (no
TCA_OPTIONS) is used on a shared block, since fw_classify()'s
old-method path needs block->q which is NULL for shared blocks.
The fixed null-ptr-deref calling stack:
KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f]
RIP: 0010:fw_classify (net/sched/cls_fw.c:81)
Call Trace:
tcf_classify (./include/net/tc_wrapper.h:197 net/sched/cls_api.c:1764 net/sched/cls_api.c:1860)
tc_run (net/core/dev.c:4401)
__dev_queue_xmit (net/core/dev.c:4535 net/core/dev.c:4790) |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: drop logically empty buckets in mtype_del
mtype_del() counts empty slots below n->pos in k, but it only drops the
bucket when both n->pos and k are zero. This misses buckets whose live
entries have all been removed while n->pos still points past deleted slots.
Treat a bucket as empty when all positions below n->pos are unused and
release it directly instead of shrinking it further. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_log: account for netlink header size
This is a followup to an old bug fix: NLMSG_DONE needs to account
for the netlink header size, not just the attribute size.
This can result in a WARN splat + drop of the netlink message,
but other than this there are no ill effects. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: avoid overflows in ip6_datagram_send_ctl()
Yiming Qian reported :
<quote>
I believe I found a locally triggerable kernel bug in the IPv6 sendmsg
ancillary-data path that can panic the kernel via `skb_under_panic()`
(local DoS).
The core issue is a mismatch between:
- a 16-bit length accumulator (`struct ipv6_txoptions::opt_flen`, type
`__u16`) and
- a pointer to the *last* provided destination-options header (`opt->dst1opt`)
when multiple `IPV6_DSTOPTS` control messages (cmsgs) are provided.
- `include/net/ipv6.h`:
- `struct ipv6_txoptions::opt_flen` is `__u16` (wrap possible).
(lines 291-307, especially 298)
- `net/ipv6/datagram.c:ip6_datagram_send_ctl()`:
- Accepts repeated `IPV6_DSTOPTS` and accumulates into `opt_flen`
without rejecting duplicates. (lines 909-933)
- `net/ipv6/ip6_output.c:__ip6_append_data()`:
- Uses `opt->opt_flen + opt->opt_nflen` to compute header
sizes/headroom decisions. (lines 1448-1466, especially 1463-1465)
- `net/ipv6/ip6_output.c:__ip6_make_skb()`:
- Calls `ipv6_push_frag_opts()` if `opt->opt_flen` is non-zero.
(lines 1930-1934)
- `net/ipv6/exthdrs.c:ipv6_push_frag_opts()` / `ipv6_push_exthdr()`:
- Push size comes from `ipv6_optlen(opt->dst1opt)` (based on the
pointed-to header). (lines 1179-1185 and 1206-1211)
1. `opt_flen` is a 16-bit accumulator:
- `include/net/ipv6.h:298` defines `__u16 opt_flen; /* after fragment hdr */`.
2. `ip6_datagram_send_ctl()` accepts *repeated* `IPV6_DSTOPTS` cmsgs
and increments `opt_flen` each time:
- In `net/ipv6/datagram.c:909-933`, for `IPV6_DSTOPTS`:
- It computes `len = ((hdr->hdrlen + 1) << 3);`
- It checks `CAP_NET_RAW` using `ns_capable(net->user_ns,
CAP_NET_RAW)`. (line 922)
- Then it does:
- `opt->opt_flen += len;` (line 927)
- `opt->dst1opt = hdr;` (line 928)
There is no duplicate rejection here (unlike the legacy
`IPV6_2292DSTOPTS` path which rejects duplicates at
`net/ipv6/datagram.c:901-904`).
If enough large `IPV6_DSTOPTS` cmsgs are provided, `opt_flen` wraps
while `dst1opt` still points to a large (2048-byte)
destination-options header.
In the attached PoC (`poc.c`):
- 32 cmsgs with `hdrlen=255` => `len = (255+1)*8 = 2048`
- 1 cmsg with `hdrlen=0` => `len = 8`
- Total increment: `32*2048 + 8 = 65544`, so `(__u16)opt_flen == 8`
- The last cmsg is 2048 bytes, so `dst1opt` points to a 2048-byte header.
3. The transmit path sizes headers using the wrapped `opt_flen`:
- In `net/ipv6/ip6_output.c:1463-1465`:
- `headersize = sizeof(struct ipv6hdr) + (opt ? opt->opt_flen +
opt->opt_nflen : 0) + ...;`
With wrapped `opt_flen`, `headersize`/headroom decisions underestimate
what will be pushed later.
4. When building the final skb, the actual push length comes from
`dst1opt` and is not limited by wrapped `opt_flen`:
- In `net/ipv6/ip6_output.c:1930-1934`:
- `if (opt->opt_flen) proto = ipv6_push_frag_opts(skb, opt, proto);`
- In `net/ipv6/exthdrs.c:1206-1211`, `ipv6_push_frag_opts()` pushes
`dst1opt` via `ipv6_push_exthdr()`.
- In `net/ipv6/exthdrs.c:1179-1184`, `ipv6_push_exthdr()` does:
- `skb_push(skb, ipv6_optlen(opt));`
- `memcpy(h, opt, ipv6_optlen(opt));`
With insufficient headroom, `skb_push()` underflows and triggers
`skb_under_panic()` -> `BUG()`:
- `net/core/skbuff.c:2669-2675` (`skb_push()` calls `skb_under_panic()`)
- `net/core/skbuff.c:207-214` (`skb_panic()` ends in `BUG()`)
- The `IPV6_DSTOPTS` cmsg path requires `CAP_NET_RAW` in the target
netns user namespace (`ns_capable(net->user_ns, CAP_NET_RAW)`).
- Root (or any task with `CAP_NET_RAW`) can trigger this without user
namespaces.
- An unprivileged `uid=1000` user can trigger this if unprivileged
user namespaces are enabled and it can create a userns+netns to obtain
namespaced `CAP_NET_RAW` (the attached PoC does this).
- Local denial of service: kernel BUG/panic (system crash).
-
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
sunrpc: fix cache_request leak in cache_release
When a reader's file descriptor is closed while in the middle of reading
a cache_request (rp->offset != 0), cache_release() decrements the
request's readers count but never checks whether it should free the
request.
In cache_read(), when readers drops to 0 and CACHE_PENDING is clear, the
cache_request is removed from the queue and freed along with its buffer
and cache_head reference. cache_release() lacks this cleanup.
The only other path that frees requests with readers == 0 is
cache_dequeue(), but it runs only when CACHE_PENDING transitions from
set to clear. If that transition already happened while readers was
still non-zero, cache_dequeue() will have skipped the request, and no
subsequent call will clean it up.
Add the same cleanup logic from cache_read() to cache_release(): after
decrementing readers, check if it reached 0 with CACHE_PENDING clear,
and if so, dequeue and free the cache_request. |
| In the Linux kernel, the following vulnerability has been resolved:
nvdimm/bus: Fix potential use after free in asynchronous initialization
Dingisoul with KASAN reports a use after free if device_add() fails in
nd_async_device_register().
Commit b6eae0f61db2 ("libnvdimm: Hold reference on parent while
scheduling async init") correctly added a reference on the parent device
to be held until asynchronous initialization was complete. However, if
device_add() results in an allocation failure the ref count of the
device drops to 0 prior to the parent pointer being accessed. Thus
resulting in use after free.
The bug bot AI correctly identified the fix. Save a reference to the
parent pointer to be used to drop the parent reference regardless of the
outcome of device_add(). |
