| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: ocb: skip rx_no_sta when interface is not joined
ieee80211_ocb_rx_no_sta() assumes a valid channel context, which is only
present after JOIN_OCB.
RX may run before JOIN_OCB is executed, in which case the OCB interface
is not operational. Skip RX peer handling when the interface is not
joined to avoid warnings in the RX path. |
| In the Linux kernel, the following vulnerability has been resolved:
media: mediatek: vcodec: Use spinlock for context list protection lock
Previously a mutex was added to protect the encoder and decoder context
lists from unexpected changes originating from the SCP IP block, causing
the context pointer to go invalid, resulting in a NULL pointer
dereference in the IPI handler.
Turns out on the MT8173, the VPU IPI handler is called from hard IRQ
context. This causes a big warning from the scheduler. This was first
reported downstream on the ChromeOS kernels, but is also reproducible
on mainline using Fluster with the FFmpeg v4l2m2m decoders. Even though
the actual capture format is not supported, the affected code paths
are triggered.
Since this lock just protects the context list and operations on it are
very fast, it should be OK to switch to a spinlock. |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "ipmi: fix msg stack when IPMI is disconnected"
This reverts commit c608966f3f9c2dca596967501d00753282b395fc.
This patch has a subtle bug that can cause the IPMI driver to go into an
infinite loop if the BMC misbehaves in a certain way. Apparently
certain BMCs do misbehave this way because several reports have come in
recently about this. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: swap: check for stable address space before operating on the VMA
It is possible to hit a zero entry while traversing the vmas in unuse_mm()
called from swapoff path and accessing it causes the OOPS:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000446--> Loading the memory from offset 0x40 on the
XA_ZERO_ENTRY as address.
Mem abort info:
ESR = 0x0000000096000005
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x05: level 1 translation fault
The issue is manifested from the below race between the fork() on a
process and swapoff:
fork(dup_mmap()) swapoff(unuse_mm)
--------------- -----------------
1) Identical mtree is built using
__mt_dup().
2) copy_pte_range()-->
copy_nonpresent_pte():
The dst mm is added into the
mmlist to be visible to the
swapoff operation.
3) Fatal signal is sent to the parent
process(which is the current during the
fork) thus skip the duplication of the
vmas and mark the vma range with
XA_ZERO_ENTRY as a marker for this process
that helps during exit_mmap().
4) swapoff is tried on the
'mm' added to the 'mmlist' as
part of the 2.
5) unuse_mm(), that iterates
through the vma's of this 'mm'
will hit the non-NULL zero entry
and operating on this zero entry
as a vma is resulting into the
oops.
The proper fix would be around not exposing this partially-valid tree to
others when droping the mmap lock, which is being solved with [1]. A
simpler solution would be checking for MMF_UNSTABLE, as it is set if
mm_struct is not fully initialized in dup_mmap().
Thanks to Liam/Lorenzo/David for all the suggestions in fixing this
issue. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: audioreach: fix potential null pointer dereference
It is possible that the topology parsing function
audioreach_widget_load_module_common() could return NULL or an error
pointer. Add missing NULL check so that we do not dereference it. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: essiv - Check ssize for decryption and in-place encryption
Move the ssize check to the start in essiv_aead_crypt so that
it's also checked for decryption and in-place encryption. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: check the return value of pinmux_ops::get_function_name()
While the API contract in docs doesn't specify it explicitly, the
generic implementation of the get_function_name() callback from struct
pinmux_ops - pinmux_generic_get_function_name() - can fail and return
NULL. This is already checked in pinmux_check_ops() so add a similar
check in pinmux_func_name_to_selector() instead of passing the returned
pointer right down to strcmp() where the NULL can get dereferenced. This
is normal operation when adding new pinfunctions. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-test: Add NULL check for DMA channels before release
The fields dma_chan_tx and dma_chan_rx of the struct pci_epf_test can be
NULL even after EPF initialization. Then it is prudent to check that
they have non-NULL values before releasing the channels. Add the checks
in pci_epf_test_clean_dma_chan().
Without the checks, NULL pointer dereferences happen and they can lead
to a kernel panic in some cases:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050
Call trace:
dma_release_channel+0x2c/0x120 (P)
pci_epf_test_epc_deinit+0x94/0xc0 [pci_epf_test]
pci_epc_deinit_notify+0x74/0xc0
tegra_pcie_ep_pex_rst_irq+0x250/0x5d8
irq_thread_fn+0x34/0xb8
irq_thread+0x18c/0x2e8
kthread+0x14c/0x210
ret_from_fork+0x10/0x20
[mani: trimmed the stack trace] |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: pru: Fix potential NULL pointer dereference in pru_rproc_set_ctable()
pru_rproc_set_ctable() accessed rproc->priv before the IS_ERR_OR_NULL
check, which could lead to a null pointer dereference. Move the pru
assignment, ensuring we never dereference a NULL rproc pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
When platform firmware supplies error information to the OS, e.g., via the
ACPI APEI GHES mechanism, it may identify an error source device that
doesn't advertise an AER Capability and therefore dev->aer_info, which
contains AER stats and ratelimiting data, is NULL.
pci_dev_aer_stats_incr() already checks dev->aer_info for NULL, but
aer_ratelimit() did not, leading to NULL pointer dereferences like this one
from the URL below:
{1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 0
{1}[Hardware Error]: event severity: corrected
{1}[Hardware Error]: device_id: 0000:00:00.0
{1}[Hardware Error]: vendor_id: 0x8086, device_id: 0x2020
{1}[Hardware Error]: aer_cor_status: 0x00001000, aer_cor_mask: 0x00002000
BUG: kernel NULL pointer dereference, address: 0000000000000264
RIP: 0010:___ratelimit+0xc/0x1b0
pci_print_aer+0x141/0x360
aer_recover_work_func+0xb5/0x130
[8086:2020] is an Intel "Sky Lake-E DMI3 Registers" device that claims to
be a Root Port but does not advertise an AER Capability.
Add a NULL check in aer_ratelimit() to avoid the NULL pointer dereference.
Note that this also prevents ratelimiting these events from GHES.
[bhelgaas: add crash details to commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: simplefb: Fix use after free in simplefb_detach_genpds()
The pm_domain cleanup can not be devres managed as it uses struct
simplefb_par which is allocated within struct fb_info by
framebuffer_alloc(). This allocation is explicitly freed by
unregister_framebuffer() in simplefb_remove().
Devres managed cleanup runs after the device remove call and thus can no
longer access struct simplefb_par.
Call simplefb_detach_genpds() explicitly from simplefb_destroy() like
the cleanup functions for clocks and regulators.
Fixes an use after free on M2 Mac mini during
aperture_remove_conflicting_devices() using the downstream asahi kernel
with Debian's kernel config. For unknown reasons this started to
consistently dereference an invalid pointer in v6.16.3 based kernels.
[ 6.736134] BUG: KASAN: slab-use-after-free in simplefb_detach_genpds+0x58/0x220
[ 6.743545] Read of size 4 at addr ffff8000304743f0 by task (udev-worker)/227
[ 6.750697]
[ 6.752182] CPU: 6 UID: 0 PID: 227 Comm: (udev-worker) Tainted: G S 6.16.3-asahi+ #16 PREEMPTLAZY
[ 6.752186] Tainted: [S]=CPU_OUT_OF_SPEC
[ 6.752187] Hardware name: Apple Mac mini (M2, 2023) (DT)
[ 6.752189] Call trace:
[ 6.752190] show_stack+0x34/0x98 (C)
[ 6.752194] dump_stack_lvl+0x60/0x80
[ 6.752197] print_report+0x17c/0x4d8
[ 6.752201] kasan_report+0xb4/0x100
[ 6.752206] __asan_report_load4_noabort+0x20/0x30
[ 6.752209] simplefb_detach_genpds+0x58/0x220
[ 6.752213] devm_action_release+0x50/0x98
[ 6.752216] release_nodes+0xd0/0x2c8
[ 6.752219] devres_release_all+0xfc/0x178
[ 6.752221] device_unbind_cleanup+0x28/0x168
[ 6.752224] device_release_driver_internal+0x34c/0x470
[ 6.752228] device_release_driver+0x20/0x38
[ 6.752231] bus_remove_device+0x1b0/0x380
[ 6.752234] device_del+0x314/0x820
[ 6.752238] platform_device_del+0x3c/0x1e8
[ 6.752242] platform_device_unregister+0x20/0x50
[ 6.752246] aperture_detach_platform_device+0x1c/0x30
[ 6.752250] aperture_detach_devices+0x16c/0x290
[ 6.752253] aperture_remove_conflicting_devices+0x34/0x50
...
[ 6.752343]
[ 6.967409] Allocated by task 62:
[ 6.970724] kasan_save_stack+0x3c/0x70
[ 6.974560] kasan_save_track+0x20/0x40
[ 6.978397] kasan_save_alloc_info+0x40/0x58
[ 6.982670] __kasan_kmalloc+0xd4/0xd8
[ 6.986420] __kmalloc_noprof+0x194/0x540
[ 6.990432] framebuffer_alloc+0xc8/0x130
[ 6.994444] simplefb_probe+0x258/0x2378
...
[ 7.054356]
[ 7.055838] Freed by task 227:
[ 7.058891] kasan_save_stack+0x3c/0x70
[ 7.062727] kasan_save_track+0x20/0x40
[ 7.066565] kasan_save_free_info+0x4c/0x80
[ 7.070751] __kasan_slab_free+0x6c/0xa0
[ 7.074675] kfree+0x10c/0x380
[ 7.077727] framebuffer_release+0x5c/0x90
[ 7.081826] simplefb_destroy+0x1b4/0x2c0
[ 7.085837] put_fb_info+0x98/0x100
[ 7.089326] unregister_framebuffer+0x178/0x320
[ 7.093861] simplefb_remove+0x3c/0x60
[ 7.097611] platform_remove+0x60/0x98
[ 7.101361] device_remove+0xb8/0x160
[ 7.105024] device_release_driver_internal+0x2fc/0x470
[ 7.110256] device_release_driver+0x20/0x38
[ 7.114529] bus_remove_device+0x1b0/0x380
[ 7.118628] device_del+0x314/0x820
[ 7.122116] platform_device_del+0x3c/0x1e8
[ 7.126302] platform_device_unregister+0x20/0x50
[ 7.131012] aperture_detach_platform_device+0x1c/0x30
[ 7.136157] aperture_detach_devices+0x16c/0x290
[ 7.140779] aperture_remove_conflicting_devices+0x34/0x50
... |
| In the Linux kernel, the following vulnerability has been resolved:
Squashfs: fix uninit-value in squashfs_get_parent
Syzkaller reports a "KMSAN: uninit-value in squashfs_get_parent" bug.
This is caused by open_by_handle_at() being called with a file handle
containing an invalid parent inode number. In particular the inode number
is that of a symbolic link, rather than a directory.
Squashfs_get_parent() gets called with that symbolic link inode, and
accesses the parent member field.
unsigned int parent_ino = squashfs_i(inode)->parent;
Because non-directory inodes in Squashfs do not have a parent value, this
is uninitialised, and this causes an uninitialised value access.
The fix is to initialise parent with the invalid inode 0, which will cause
an EINVAL error to be returned.
Regular inodes used to share the parent field with the block_list_start
field. This is removed in this commit to enable the parent field to
contain the invalid inode number 0. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Skip scalar adjustment for BPF_NEG if dst is a pointer
In check_alu_op(), the verifier currently calls check_reg_arg() and
adjust_scalar_min_max_vals() unconditionally for BPF_NEG operations.
However, if the destination register holds a pointer, these scalar
adjustments are unnecessary and potentially incorrect.
This patch adds a check to skip the adjustment logic when the destination
register contains a pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix crypto buffers in non-linear memory
The crypto API, through the scatterlist API, expects input buffers to be
in linear memory. We handle this with the cifs_sg_set_buf() helper
that converts vmalloc'd memory to their corresponding pages.
However, when we allocate our aead_request buffer (@creq in
smb2ops.c::crypt_message()), we do so with kvzalloc(), which possibly
puts aead_request->__ctx in vmalloc area.
AEAD algorithm then uses ->__ctx for its private/internal data and
operations, and uses sg_set_buf() for such data on a few places.
This works fine as long as @creq falls into kmalloc zone (small
requests) or vmalloc'd memory is still within linear range.
Tasks' stacks are vmalloc'd by default (CONFIG_VMAP_STACK=y), so too
many tasks will increment the base stacks' addresses to a point where
virt_addr_valid(buf) will fail (BUG() in sg_set_buf()) when that
happens.
In practice: too many parallel reads and writes on an encrypted mount
will trigger this bug.
To fix this, always alloc @creq with kmalloc() instead.
Also drop the @sensitive_size variable/arguments since
kfree_sensitive() doesn't need it.
Backtrace:
[ 945.272081] ------------[ cut here ]------------
[ 945.272774] kernel BUG at include/linux/scatterlist.h:209!
[ 945.273520] Oops: invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC NOPTI
[ 945.274412] CPU: 7 UID: 0 PID: 56 Comm: kworker/u33:0 Kdump: loaded Not tainted 6.15.0-lku-11779-g8e9d6efccdd7-dirty #1 PREEMPT(voluntary)
[ 945.275736] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-2-gc13ff2cd-prebuilt.qemu.org 04/01/2014
[ 945.276877] Workqueue: writeback wb_workfn (flush-cifs-2)
[ 945.277457] RIP: 0010:crypto_gcm_init_common+0x1f9/0x220
[ 945.278018] Code: b0 00 00 00 48 83 c4 08 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc 48 c7 c0 00 00 00 80 48 2b 05 5c 58 e5 00 e9 58 ff ff ff <0f> 0b 0f 0b 0f 0b 0f 0b 0f 0b 0f 0b 48 c7 04 24 01 00 00 00 48 8b
[ 945.279992] RSP: 0018:ffffc90000a27360 EFLAGS: 00010246
[ 945.280578] RAX: 0000000000000000 RBX: ffffc90001d85060 RCX: 0000000000000030
[ 945.281376] RDX: 0000000000080000 RSI: 0000000000000000 RDI: ffffc90081d85070
[ 945.282145] RBP: ffffc90001d85010 R08: ffffc90001d85000 R09: 0000000000000000
[ 945.282898] R10: ffffc90001d85090 R11: 0000000000001000 R12: ffffc90001d85070
[ 945.283656] R13: ffff888113522948 R14: ffffc90001d85060 R15: ffffc90001d85010
[ 945.284407] FS: 0000000000000000(0000) GS:ffff8882e66cf000(0000) knlGS:0000000000000000
[ 945.285262] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 945.285884] CR2: 00007fa7ffdd31f4 CR3: 000000010540d000 CR4: 0000000000350ef0
[ 945.286683] Call Trace:
[ 945.286952] <TASK>
[ 945.287184] ? crypt_message+0x33f/0xad0 [cifs]
[ 945.287719] crypto_gcm_encrypt+0x36/0xe0
[ 945.288152] crypt_message+0x54a/0xad0 [cifs]
[ 945.288724] smb3_init_transform_rq+0x277/0x300 [cifs]
[ 945.289300] smb_send_rqst+0xa3/0x160 [cifs]
[ 945.289944] cifs_call_async+0x178/0x340 [cifs]
[ 945.290514] ? __pfx_smb2_writev_callback+0x10/0x10 [cifs]
[ 945.291177] smb2_async_writev+0x3e3/0x670 [cifs]
[ 945.291759] ? find_held_lock+0x32/0x90
[ 945.292212] ? netfs_advance_write+0xf2/0x310
[ 945.292723] netfs_advance_write+0xf2/0x310
[ 945.293210] netfs_write_folio+0x346/0xcc0
[ 945.293689] ? __pfx__raw_spin_unlock_irq+0x10/0x10
[ 945.294250] netfs_writepages+0x117/0x460
[ 945.294724] do_writepages+0xbe/0x170
[ 945.295152] ? find_held_lock+0x32/0x90
[ 945.295600] ? kvm_sched_clock_read+0x11/0x20
[ 945.296103] __writeback_single_inode+0x56/0x4b0
[ 945.296643] writeback_sb_inodes+0x229/0x550
[ 945.297140] __writeback_inodes_wb+0x4c/0xe0
[ 945.297642] wb_writeback+0x2f1/0x3f0
[ 945.298069] wb_workfn+0x300/0x490
[ 945.298472] process_one_work+0x1fe/0x590
[ 945.298949] worker_thread+0x1ce/0x3c0
[ 945.299397] ? __pfx_worker_thread+0x10/0x10
[ 945.299900] kthr
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: trbe: Return NULL pointer for allocation failures
When the TRBE driver fails to allocate a buffer, it currently returns
the error code "-ENOMEM". However, the caller etm_setup_aux() only
checks for a NULL pointer, so it misses the error. As a result, the
driver continues and eventually causes a kernel panic.
Fix this by returning a NULL pointer from arm_trbe_alloc_buffer() on
allocation failures. This allows that the callers can properly handle
the failure. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: hisilicon/qm - set NULL to qm->debug.qm_diff_regs
When the initialization of qm->debug.acc_diff_reg fails,
the probe process does not exit. However, after qm->debug.qm_diff_regs is
freed, it is not set to NULL. This can lead to a double free when the
remove process attempts to free it again. Therefore, qm->debug.qm_diff_regs
should be set to NULL after it is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: comp - Use same definition of context alloc and free ops
In commit 42d9f6c77479 ("crypto: acomp - Move scomp stream allocation
code into acomp"), the crypto_acomp_streams struct was made to rely on
having the alloc_ctx and free_ctx operations defined in the same order
as the scomp_alg struct. But in that same commit, the alloc_ctx and
free_ctx members of scomp_alg may be randomized by structure layout
randomization, since they are contained in a pure ops structure
(containing only function pointers). If the pointers within scomp_alg
are randomized, but those in crypto_acomp_streams are not, then
the order may no longer match. This fixes the problem by removing the
union from scomp_alg so that both crypto_acomp_streams and scomp_alg
will share the same definition of alloc_ctx and free_ctx, ensuring
they will always have the same layout. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: KVM: Write hgatp register with valid mode bits
According to the RISC-V Privileged Architecture Spec, when MODE=Bare
is selected,software must write zero to the remaining fields of hgatp.
We have detected the valid mode supported by the HW before, So using a
valid mode to detect how many vmid bits are supported. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: n_gsm: Don't block input queue by waiting MSC
Currently gsm_queue() processes incoming frames and when opening
a DLC channel it calls gsm_dlci_open() which calls gsm_modem_update().
If basic mode is used it calls gsm_modem_upd_via_msc() and it
cannot block the input queue by waiting the response to come
into the same input queue.
Instead allow sending Modem Status Command without waiting for remote
end to respond. Define a new function gsm_modem_send_initial_msc()
for this purpose. As MSC is only valid for basic encoding, it does
not do anything for advanced or when convergence layer type 2 is used. |
| In the Linux kernel, the following vulnerability has been resolved:
fanotify: Validate the return value of mnt_ns_from_dentry() before dereferencing
The function do_fanotify_mark() does not validate if
mnt_ns_from_dentry() returns NULL before dereferencing mntns->user_ns.
This causes a NULL pointer dereference in do_fanotify_mark() if the
path is not a mount namespace object.
Fix this by checking mnt_ns_from_dentry()'s return value before
dereferencing it.
Before the patch
$ gcc fanotify_nullptr.c -o fanotify_nullptr
$ mkdir A
$ ./fanotify_nullptr
Fanotify fd: 3
fanotify_mark: Operation not permitted
$ unshare -Urm
Fanotify fd: 3
Killed
int main(void){
int ffd;
ffd = fanotify_init(FAN_CLASS_NOTIF | FAN_REPORT_MNT, 0);
if(ffd < 0){
perror("fanotify_init");
exit(EXIT_FAILURE);
}
printf("Fanotify fd: %d\n",ffd);
if(fanotify_mark(ffd, FAN_MARK_ADD | FAN_MARK_MNTNS,
FAN_MNT_ATTACH, AT_FDCWD, "A") < 0){
perror("fanotify_mark");
exit(EXIT_FAILURE);
}
return 0;
}
After the patch
$ gcc fanotify_nullptr.c -o fanotify_nullptr
$ mkdir A
$ ./fanotify_nullptr
Fanotify fd: 3
fanotify_mark: Operation not permitted
$ unshare -Urm
Fanotify fd: 3
fanotify_mark: Invalid argument
[ 25.694973] BUG: kernel NULL pointer dereference, address: 0000000000000038
[ 25.695006] #PF: supervisor read access in kernel mode
[ 25.695012] #PF: error_code(0x0000) - not-present page
[ 25.695017] PGD 109a30067 P4D 109a30067 PUD 142b46067 PMD 0
[ 25.695025] Oops: Oops: 0000 [#1] SMP NOPTI
[ 25.695032] CPU: 4 UID: 1000 PID: 1478 Comm: fanotify_nullpt Not
tainted 6.17.0-rc4 #1 PREEMPT(lazy)
[ 25.695040] Hardware name: VMware, Inc. VMware Virtual
Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020
[ 25.695049] RIP: 0010:do_fanotify_mark+0x817/0x950
[ 25.695066] Code: 04 00 00 e9 45 fd ff ff 48 8b 7c 24 48 4c 89 54
24 18 4c 89 5c 24 10 4c 89 0c 24 e8 b3 11 fc ff 4c 8b 54 24 18 4c 8b
5c 24 10 <48> 8b 78 38 4c 8b 0c 24 49 89 c4 e9 13 fd ff ff 8b 4c 24 28
85 c9
[ 25.695081] RSP: 0018:ffffd31c469e3c08 EFLAGS: 00010203
[ 25.695104] RAX: 0000000000000000 RBX: 0000000001000000 RCX: ffff8eb48aebd220
[ 25.695110] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8eb4835e8180
[ 25.695115] RBP: 0000000000000111 R08: 0000000000000000 R09: 0000000000000000
[ 25.695142] R10: ffff8eb48a7d56c0 R11: ffff8eb482bede00 R12: 00000000004012a7
[ 25.695148] R13: 0000000000000110 R14: 0000000000000001 R15: ffff8eb48a7d56c0
[ 25.695154] FS: 00007f8733bda740(0000) GS:ffff8eb61ce5f000(0000)
knlGS:0000000000000000
[ 25.695162] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 25.695170] CR2: 0000000000000038 CR3: 0000000136994006 CR4: 00000000003706f0
[ 25.695201] Call Trace:
[ 25.695209] <TASK>
[ 25.695215] __x64_sys_fanotify_mark+0x1f/0x30
[ 25.695222] do_syscall_64+0x82/0x2c0
... |
