| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Disable bottom softirqs as part of spin_lock_irq() on PREEMPT_RT
snd_pcm_group_lock_irq() acquires a spinlock_t and disables interrupts
via spin_lock_irq(). This also implicitly disables the handling of
softirqs such as TIMER_SOFTIRQ.
On PREEMPT_RT softirqs are preemptible and spin_lock_irq() does not
disable them. That means a timer can be invoked during spin_lock_irq()
on the same CPU. Due to synchronisations reasons local_bh_disable() has
a per-CPU lock named softirq_ctrl.lock which synchronizes individual
softirq against each other.
syz-bot managed to trigger a lockdep report where softirq_ctrl.lock is
acquired in hrtimer_cancel() in addition to hrtimer_run_softirq(). This
is a possible deadlock.
The softirq_ctrl.lock can not be made part of spin_lock_irq() as this
would lead to too much synchronisation against individual threads on the
system. To avoid the possible deadlock, softirqs must be manually
disabled before the lock is acquired.
Disable softirqs before the lock is acquired on PREEMPT_RT. |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: fix module removal if firmware download failed
Fix remove if firmware failed to load:
qcom-iris aa00000.video-codec: Direct firmware load for qcom/vpu/vpu33_p4.mbn failed with error -2
qcom-iris aa00000.video-codec: firmware download failed
qcom-iris aa00000.video-codec: core init failed
then:
$ echo aa00000.video-codec > /sys/bus/platform/drivers/qcom-iris/unbind
Triggers:
genpd genpd:1:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
video_cc_mvs0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#1: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
video_cc_mvs0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#2: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
genpd genpd:0:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
gcc_video_axi0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#4: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
------------[ cut here ]------------
gcc_video_axi0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#4: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
Skip deinit if initialization never succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
netconsole: Acquire su_mutex before navigating configs hierarchy
There is a race between operations that iterate over the userdata
cg_children list and concurrent add/remove of userdata items through
configfs. The update_userdata() function iterates over the
nt->userdata_group.cg_children list, and count_extradata_entries() also
iterates over this same list to count nodes.
Quoting from Documentation/filesystems/configfs.rst:
> A subsystem can navigate the cg_children list and the ci_parent pointer
> to see the tree created by the subsystem. This can race with configfs'
> management of the hierarchy, so configfs uses the subsystem mutex to
> protect modifications. Whenever a subsystem wants to navigate the
> hierarchy, it must do so under the protection of the subsystem
> mutex.
Without proper locking, if a userdata item is added or removed
concurrently while these functions are iterating, the list can be
accessed in an inconsistent state. For example, the list_for_each() loop
can reach a node that is being removed from the list by list_del_init()
which sets the nodes' .next pointer to point to itself, so the loop will
never end (or reach the WARN_ON_ONCE in update_userdata() ).
Fix this by holding the configfs subsystem mutex (su_mutex) during all
operations that iterate over cg_children.
This includes:
- userdatum_value_store() which calls update_userdata() to iterate over
cg_children
- All sysdata_*_enabled_store() functions which call
count_extradata_entries() to iterate over cg_children
The su_mutex must be acquired before dynamic_netconsole_mutex to avoid
potential lock ordering issues, as configfs operations may already hold
su_mutex when calling into our code. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: check the return value of pinmux_ops::get_function_name()
While the API contract in docs doesn't specify it explicitly, the
generic implementation of the get_function_name() callback from struct
pinmux_ops - pinmux_generic_get_function_name() - can fail and return
NULL. This is already checked in pinmux_check_ops() so add a similar
check in pinmux_func_name_to_selector() instead of passing the returned
pointer right down to strcmp() where the NULL can get dereferenced. This
is normal operation when adding new pinfunctions. |
| In the Linux kernel, the following vulnerability has been resolved:
parisc: Avoid crash due to unaligned access in unwinder
Guenter Roeck reported this kernel crash on his emulated B160L machine:
Starting network: udhcpc: started, v1.36.1
Backtrace:
[<104320d4>] unwind_once+0x1c/0x5c
[<10434a00>] walk_stackframe.isra.0+0x74/0xb8
[<10434a6c>] arch_stack_walk+0x28/0x38
[<104e5efc>] stack_trace_save+0x48/0x5c
[<105d1bdc>] set_track_prepare+0x44/0x6c
[<105d9c80>] ___slab_alloc+0xfc4/0x1024
[<105d9d38>] __slab_alloc.isra.0+0x58/0x90
[<105dc80c>] kmem_cache_alloc_noprof+0x2ac/0x4a0
[<105b8e54>] __anon_vma_prepare+0x60/0x280
[<105a823c>] __vmf_anon_prepare+0x68/0x94
[<105a8b34>] do_wp_page+0x8cc/0xf10
[<105aad88>] handle_mm_fault+0x6c0/0xf08
[<10425568>] do_page_fault+0x110/0x440
[<10427938>] handle_interruption+0x184/0x748
[<11178398>] schedule+0x4c/0x190
BUG: spinlock recursion on CPU#0, ifconfig/2420
lock: terminate_lock.2+0x0/0x1c, .magic: dead4ead, .owner: ifconfig/2420, .owner_cpu: 0
While creating the stack trace, the unwinder uses the stack pointer to guess
the previous frame to read the previous stack pointer from memory. The crash
happens, because the unwinder tries to read from unaligned memory and as such
triggers the unalignment trap handler which then leads to the spinlock
recursion and finally to a deadlock.
Fix it by checking the alignment before accessing the memory. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix KASAN global-out-of-bounds warning
When running "perf mem record" command on CWF, the below KASAN
global-out-of-bounds warning is seen.
==================================================================
BUG: KASAN: global-out-of-bounds in cmt_latency_data+0x176/0x1b0
Read of size 4 at addr ffffffffb721d000 by task dtlb/9850
Call Trace:
kasan_report+0xb8/0xf0
cmt_latency_data+0x176/0x1b0
setup_arch_pebs_sample_data+0xf49/0x2560
intel_pmu_drain_arch_pebs+0x577/0xb00
handle_pmi_common+0x6c4/0xc80
The issue is caused by below code in __grt_latency_data(). The code
tries to access x86_hybrid_pmu structure which doesn't exist on
non-hybrid platform like CWF.
WARN_ON_ONCE(hybrid_pmu(event->pmu)->pmu_type == hybrid_big)
So add is_hybrid() check before calling this WARN_ON_ONCE to fix the
global-out-of-bounds access issue. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/atom: Check kcalloc() for WS buffer in amdgpu_atom_execute_table_locked()
kcalloc() may fail. When WS is non-zero and allocation fails, ectx.ws
remains NULL while ectx.ws_size is set, leading to a potential NULL
pointer dereference in atom_get_src_int() when accessing WS entries.
Return -ENOMEM on allocation failure to avoid the NULL dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
sysfs: check visibility before changing group attribute ownership
Since commit 0c17270f9b92 ("net: sysfs: Implement is_visible for
phys_(port_id, port_name, switch_id)"), __dev_change_net_namespace() can
hit WARN_ON() when trying to change owner of a file that isn't visible.
See the trace below:
WARNING: CPU: 6 PID: 2938 at net/core/dev.c:12410 __dev_change_net_namespace+0xb89/0xc30
CPU: 6 UID: 0 PID: 2938 Comm: incusd Not tainted 6.17.1-1-mainline #1 PREEMPT(full) 4b783b4a638669fb644857f484487d17cb45ed1f
Hardware name: Framework Laptop 13 (AMD Ryzen 7040Series)/FRANMDCP07, BIOS 03.07 02/19/2025
RIP: 0010:__dev_change_net_namespace+0xb89/0xc30
[...]
Call Trace:
<TASK>
? if6_seq_show+0x30/0x50
do_setlink.isra.0+0xc7/0x1270
? __nla_validate_parse+0x5c/0xcc0
? security_capable+0x94/0x1a0
rtnl_newlink+0x858/0xc20
? update_curr+0x8e/0x1c0
? update_entity_lag+0x71/0x80
? sched_balance_newidle+0x358/0x450
? psi_task_switch+0x113/0x2a0
? __pfx_rtnl_newlink+0x10/0x10
rtnetlink_rcv_msg+0x346/0x3e0
? sched_clock+0x10/0x30
? __pfx_rtnetlink_rcv_msg+0x10/0x10
netlink_rcv_skb+0x59/0x110
netlink_unicast+0x285/0x3c0
? __alloc_skb+0xdb/0x1a0
netlink_sendmsg+0x20d/0x430
____sys_sendmsg+0x39f/0x3d0
? import_iovec+0x2f/0x40
___sys_sendmsg+0x99/0xe0
__sys_sendmsg+0x8a/0xf0
do_syscall_64+0x81/0x970
? __sys_bind+0xe3/0x110
? syscall_exit_work+0x143/0x1b0
? do_syscall_64+0x244/0x970
? sock_alloc_file+0x63/0xc0
? syscall_exit_work+0x143/0x1b0
? do_syscall_64+0x244/0x970
? alloc_fd+0x12e/0x190
? put_unused_fd+0x2a/0x70
? do_sys_openat2+0xa2/0xe0
? syscall_exit_work+0x143/0x1b0
? do_syscall_64+0x244/0x970
? exc_page_fault+0x7e/0x1a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
</TASK>
Fix this by checking is_visible() before trying to touch the attribute. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: mte: Do not warn if the page is already tagged in copy_highpage()
The arm64 copy_highpage() assumes that the destination page is newly
allocated and not MTE-tagged (PG_mte_tagged unset) and warns
accordingly. However, following commit 060913999d7a ("mm: migrate:
support poisoned recover from migrate folio"), folio_mc_copy() is called
before __folio_migrate_mapping(). If the latter fails (-EAGAIN), the
copy will be done again to the same destination page. Since
copy_highpage() already set the PG_mte_tagged flag, this second copy
will warn.
Replace the WARN_ON_ONCE(page already tagged) in the arm64
copy_highpage() with a comment. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix NULL pointer dereference in __dm_suspend()
There is a race condition between dm device suspend and table load that
can lead to null pointer dereference. The issue occurs when suspend is
invoked before table load completes:
BUG: kernel NULL pointer dereference, address: 0000000000000054
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 6 PID: 6798 Comm: dmsetup Not tainted 6.6.0-g7e52f5f0ca9b #62
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
RIP: 0010:blk_mq_wait_quiesce_done+0x0/0x50
Call Trace:
<TASK>
blk_mq_quiesce_queue+0x2c/0x50
dm_stop_queue+0xd/0x20
__dm_suspend+0x130/0x330
dm_suspend+0x11a/0x180
dev_suspend+0x27e/0x560
ctl_ioctl+0x4cf/0x850
dm_ctl_ioctl+0xd/0x20
vfs_ioctl+0x1d/0x50
__se_sys_ioctl+0x9b/0xc0
__x64_sys_ioctl+0x19/0x30
x64_sys_call+0x2c4a/0x4620
do_syscall_64+0x9e/0x1b0
The issue can be triggered as below:
T1 T2
dm_suspend table_load
__dm_suspend dm_setup_md_queue
dm_mq_init_request_queue
blk_mq_init_allocated_queue
=> q->mq_ops = set->ops; (1)
dm_stop_queue / dm_wait_for_completion
=> q->tag_set NULL pointer! (2)
=> q->tag_set = set; (3)
Fix this by checking if a valid table (map) exists before performing
request-based suspend and waiting for target I/O. When map is NULL,
skip these table-dependent suspend steps.
Even when map is NULL, no I/O can reach any target because there is
no table loaded; I/O submitted in this state will fail early in the
DM layer. Skipping the table-dependent suspend logic in this case
is safe and avoids NULL pointer dereferences. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/mellanox: mlxbf-pmc: add sysfs_attr_init() to count_clock init
The lock-related debug logic (CONFIG_LOCK_STAT) in the kernel is noting
the following warning when the BlueField-3 SOC is booted:
BUG: key ffff00008a3402a8 has not been registered!
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 4 PID: 592 at kernel/locking/lockdep.c:4801 lockdep_init_map_type+0x1d4/0x2a0
<snip>
Call trace:
lockdep_init_map_type+0x1d4/0x2a0
__kernfs_create_file+0x84/0x140
sysfs_add_file_mode_ns+0xcc/0x1cc
internal_create_group+0x110/0x3d4
internal_create_groups.part.0+0x54/0xcc
sysfs_create_groups+0x24/0x40
device_add+0x6e8/0x93c
device_register+0x28/0x40
__hwmon_device_register+0x4b0/0x8a0
devm_hwmon_device_register_with_groups+0x7c/0xe0
mlxbf_pmc_probe+0x1e8/0x3e0 [mlxbf_pmc]
platform_probe+0x70/0x110
The mlxbf_pmc driver must call sysfs_attr_init() during the
initialization of the "count_clock" data structure to avoid
this warning. |
| In the Linux kernel, the following vulnerability has been resolved:
arch_topology: Fix incorrect error check in topology_parse_cpu_capacity()
Fix incorrect use of PTR_ERR_OR_ZERO() in topology_parse_cpu_capacity()
which causes the code to proceed with NULL clock pointers. The current
logic uses !PTR_ERR_OR_ZERO(cpu_clk) which evaluates to true for both
valid pointers and NULL, leading to potential NULL pointer dereference
in clk_get_rate().
Per include/linux/err.h documentation, PTR_ERR_OR_ZERO(ptr) returns:
"The error code within @ptr if it is an error pointer; 0 otherwise."
This means PTR_ERR_OR_ZERO() returns 0 for both valid pointers AND NULL
pointers. Therefore !PTR_ERR_OR_ZERO(cpu_clk) evaluates to true (proceed)
when cpu_clk is either valid or NULL, causing clk_get_rate(NULL) to be
called when of_clk_get() returns NULL.
Replace with !IS_ERR_OR_NULL(cpu_clk) which only proceeds for valid
pointers, preventing potential NULL pointer dereference in clk_get_rate(). |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: ks-sa - fix division by zero in ks_sa_rng_init
Fix division by zero in ks_sa_rng_init caused by missing clock
pointer initialization. The clk_get_rate() call is performed on
an uninitialized clk pointer, resulting in division by zero when
calculating delay values.
Add clock initialization code before using the clock.
drivers/char/hw_random/ks-sa-rng.c | 7 +++++++
1 file changed, 7 insertions(+) |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: asix: hold PM usage ref to avoid PM/MDIO + RTNL deadlock
Prevent USB runtime PM (autosuspend) for AX88772* in bind.
usbnet enables runtime PM (autosuspend) by default, so disabling it via
the usb_driver flag is ineffective. On AX88772B, autosuspend shows no
measurable power saving with current driver (no link partner, admin
up/down). The ~0.453 W -> ~0.248 W drop on v6.1 comes from phylib powering
the PHY off on admin-down, not from USB autosuspend.
The real hazard is that with runtime PM enabled, ndo_open() (under RTNL)
may synchronously trigger autoresume (usb_autopm_get_interface()) into
asix_resume() while the USB PM lock is held. Resume paths then invoke
phylink/phylib and MDIO, which also expect RTNL, leading to possible
deadlocks or PM lock vs MDIO wake issues.
To avoid this, keep the device runtime-PM active by taking a usage
reference in ax88772_bind() and dropping it in unbind(). A non-zero PM
usage count blocks runtime suspend regardless of userspace policy
(.../power/control - pm_runtime_allow/forbid), making this approach
robust against sysfs overrides.
Holding a runtime-PM usage ref does not affect system-wide suspend;
system sleep/resume callbacks continue to run as before. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: check kobject state_in_sysfs before deleting in blk_mq_unregister_hctx
In __blk_mq_update_nr_hw_queues() the return value of
blk_mq_sysfs_register_hctxs() is not checked. If sysfs creation for hctx
fails, later changing the number of hw_queues or removing disk will
trigger the following warning:
kernfs: can not remove 'nr_tags', no directory
WARNING: CPU: 2 PID: 637 at fs/kernfs/dir.c:1707 kernfs_remove_by_name_ns+0x13f/0x160
Call Trace:
remove_files.isra.1+0x38/0xb0
sysfs_remove_group+0x4d/0x100
sysfs_remove_groups+0x31/0x60
__kobject_del+0x23/0xf0
kobject_del+0x17/0x40
blk_mq_unregister_hctx+0x5d/0x80
blk_mq_sysfs_unregister_hctxs+0x94/0xd0
blk_mq_update_nr_hw_queues+0x124/0x760
nullb_update_nr_hw_queues+0x71/0xf0 [null_blk]
nullb_device_submit_queues_store+0x92/0x120 [null_blk]
kobjct_del() was called unconditionally even if sysfs creation failed.
Fix it by checkig the kobject creation statusbefore deleting it. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-test: Add NULL check for DMA channels before release
The fields dma_chan_tx and dma_chan_rx of the struct pci_epf_test can be
NULL even after EPF initialization. Then it is prudent to check that
they have non-NULL values before releasing the channels. Add the checks
in pci_epf_test_clean_dma_chan().
Without the checks, NULL pointer dereferences happen and they can lead
to a kernel panic in some cases:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050
Call trace:
dma_release_channel+0x2c/0x120 (P)
pci_epf_test_epc_deinit+0x94/0xc0 [pci_epf_test]
pci_epc_deinit_notify+0x74/0xc0
tegra_pcie_ep_pex_rst_irq+0x250/0x5d8
irq_thread_fn+0x34/0xb8
irq_thread+0x18c/0x2e8
kthread+0x14c/0x210
ret_from_fork+0x10/0x20
[mani: trimmed the stack trace] |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: pru: Fix potential NULL pointer dereference in pru_rproc_set_ctable()
pru_rproc_set_ctable() accessed rproc->priv before the IS_ERR_OR_NULL
check, which could lead to a null pointer dereference. Move the pru
assignment, ensuring we never dereference a NULL rproc pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
When platform firmware supplies error information to the OS, e.g., via the
ACPI APEI GHES mechanism, it may identify an error source device that
doesn't advertise an AER Capability and therefore dev->aer_info, which
contains AER stats and ratelimiting data, is NULL.
pci_dev_aer_stats_incr() already checks dev->aer_info for NULL, but
aer_ratelimit() did not, leading to NULL pointer dereferences like this one
from the URL below:
{1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 0
{1}[Hardware Error]: event severity: corrected
{1}[Hardware Error]: device_id: 0000:00:00.0
{1}[Hardware Error]: vendor_id: 0x8086, device_id: 0x2020
{1}[Hardware Error]: aer_cor_status: 0x00001000, aer_cor_mask: 0x00002000
BUG: kernel NULL pointer dereference, address: 0000000000000264
RIP: 0010:___ratelimit+0xc/0x1b0
pci_print_aer+0x141/0x360
aer_recover_work_func+0xb5/0x130
[8086:2020] is an Intel "Sky Lake-E DMI3 Registers" device that claims to
be a Root Port but does not advertise an AER Capability.
Add a NULL check in aer_ratelimit() to avoid the NULL pointer dereference.
Note that this also prevents ratelimiting these events from GHES.
[bhelgaas: add crash details to commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: simplefb: Fix use after free in simplefb_detach_genpds()
The pm_domain cleanup can not be devres managed as it uses struct
simplefb_par which is allocated within struct fb_info by
framebuffer_alloc(). This allocation is explicitly freed by
unregister_framebuffer() in simplefb_remove().
Devres managed cleanup runs after the device remove call and thus can no
longer access struct simplefb_par.
Call simplefb_detach_genpds() explicitly from simplefb_destroy() like
the cleanup functions for clocks and regulators.
Fixes an use after free on M2 Mac mini during
aperture_remove_conflicting_devices() using the downstream asahi kernel
with Debian's kernel config. For unknown reasons this started to
consistently dereference an invalid pointer in v6.16.3 based kernels.
[ 6.736134] BUG: KASAN: slab-use-after-free in simplefb_detach_genpds+0x58/0x220
[ 6.743545] Read of size 4 at addr ffff8000304743f0 by task (udev-worker)/227
[ 6.750697]
[ 6.752182] CPU: 6 UID: 0 PID: 227 Comm: (udev-worker) Tainted: G S 6.16.3-asahi+ #16 PREEMPTLAZY
[ 6.752186] Tainted: [S]=CPU_OUT_OF_SPEC
[ 6.752187] Hardware name: Apple Mac mini (M2, 2023) (DT)
[ 6.752189] Call trace:
[ 6.752190] show_stack+0x34/0x98 (C)
[ 6.752194] dump_stack_lvl+0x60/0x80
[ 6.752197] print_report+0x17c/0x4d8
[ 6.752201] kasan_report+0xb4/0x100
[ 6.752206] __asan_report_load4_noabort+0x20/0x30
[ 6.752209] simplefb_detach_genpds+0x58/0x220
[ 6.752213] devm_action_release+0x50/0x98
[ 6.752216] release_nodes+0xd0/0x2c8
[ 6.752219] devres_release_all+0xfc/0x178
[ 6.752221] device_unbind_cleanup+0x28/0x168
[ 6.752224] device_release_driver_internal+0x34c/0x470
[ 6.752228] device_release_driver+0x20/0x38
[ 6.752231] bus_remove_device+0x1b0/0x380
[ 6.752234] device_del+0x314/0x820
[ 6.752238] platform_device_del+0x3c/0x1e8
[ 6.752242] platform_device_unregister+0x20/0x50
[ 6.752246] aperture_detach_platform_device+0x1c/0x30
[ 6.752250] aperture_detach_devices+0x16c/0x290
[ 6.752253] aperture_remove_conflicting_devices+0x34/0x50
...
[ 6.752343]
[ 6.967409] Allocated by task 62:
[ 6.970724] kasan_save_stack+0x3c/0x70
[ 6.974560] kasan_save_track+0x20/0x40
[ 6.978397] kasan_save_alloc_info+0x40/0x58
[ 6.982670] __kasan_kmalloc+0xd4/0xd8
[ 6.986420] __kmalloc_noprof+0x194/0x540
[ 6.990432] framebuffer_alloc+0xc8/0x130
[ 6.994444] simplefb_probe+0x258/0x2378
...
[ 7.054356]
[ 7.055838] Freed by task 227:
[ 7.058891] kasan_save_stack+0x3c/0x70
[ 7.062727] kasan_save_track+0x20/0x40
[ 7.066565] kasan_save_free_info+0x4c/0x80
[ 7.070751] __kasan_slab_free+0x6c/0xa0
[ 7.074675] kfree+0x10c/0x380
[ 7.077727] framebuffer_release+0x5c/0x90
[ 7.081826] simplefb_destroy+0x1b4/0x2c0
[ 7.085837] put_fb_info+0x98/0x100
[ 7.089326] unregister_framebuffer+0x178/0x320
[ 7.093861] simplefb_remove+0x3c/0x60
[ 7.097611] platform_remove+0x60/0x98
[ 7.101361] device_remove+0xb8/0x160
[ 7.105024] device_release_driver_internal+0x2fc/0x470
[ 7.110256] device_release_driver+0x20/0x38
[ 7.114529] bus_remove_device+0x1b0/0x380
[ 7.118628] device_del+0x314/0x820
[ 7.122116] platform_device_del+0x3c/0x1e8
[ 7.126302] platform_device_unregister+0x20/0x50
[ 7.131012] aperture_detach_platform_device+0x1c/0x30
[ 7.136157] aperture_detach_devices+0x16c/0x290
[ 7.140779] aperture_remove_conflicting_devices+0x34/0x50
... |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: bytcr_rt5651: Fix invalid quirk input mapping
When an invalid value is passed via quirk option, currently
bytcr_rt5640 driver just ignores and leaves as is, which may lead to
unepxected results like OOB access.
This patch adds the sanity check and corrects the input mapping to the
certain default value if an invalid value is passed. |
