| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drbd: only clone bio if we have a backing device
Commit c347a787e34cb (drbd: set ->bi_bdev in drbd_req_new) moved a
bio_set_dev call (which has since been removed) to "earlier", from
drbd_request_prepare to drbd_req_new.
The problem is that this accesses device->ldev->backing_bdev, which is
not NULL-checked at this point. When we don't have an ldev (i.e. when
the DRBD device is diskless), this leads to a null pointer deref.
So, only allocate the private_bio if we actually have a disk. This is
also a small optimization, since we don't clone the bio to only to
immediately free it again in the diskless case. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix incomplete state save in rxe_requester
If a send packet is dropped by the IP layer in rxe_requester()
the call to rxe_xmit_packet() can fail with err == -EAGAIN.
To recover, the state of the wqe is restored to the state before
the packet was sent so it can be resent. However, the routines
that save and restore the state miss a significnt part of the
variable state in the wqe, the dma struct which is used to process
through the sge table. And, the state is not saved before the packet
is built which modifies the dma struct.
Under heavy stress testing with many QPs on a fast node sending
large messages to a slow node dropped packets are observed and
the resent packets are corrupted because the dma struct was not
restored. This patch fixes this behavior and allows the test cases
to succeed. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix sdma v4 sw fini error
Fix sdma v4 sw fini error for sdma 4.2.2 to
solve the following general protection fault
[ +0.108196] general protection fault, probably for non-canonical
address 0xd5e5a4ae79d24a32: 0000 [#1] PREEMPT SMP PTI
[ +0.000018] RIP: 0010:free_fw_priv+0xd/0x70
[ +0.000022] Call Trace:
[ +0.000012] <TASK>
[ +0.000011] release_firmware+0x55/0x80
[ +0.000021] amdgpu_ucode_release+0x11/0x20 [amdgpu]
[ +0.000415] amdgpu_sdma_destroy_inst_ctx+0x4f/0x90 [amdgpu]
[ +0.000360] sdma_v4_0_sw_fini+0xce/0x110 [amdgpu] |
| In the Linux kernel, the following vulnerability has been resolved:
bus: mhi: host: Range check CHDBOFF and ERDBOFF
If the value read from the CHDBOFF and ERDBOFF registers is outside the
range of the MHI register space then an invalid address might be computed
which later causes a kernel panic. Range check the read value to prevent
a crash due to bad data from the device. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: Rework long task execution when adding/deleting entries
When adding/deleting large number of elements in one step in ipset, it can
take a reasonable amount of time and can result in soft lockup errors. The
patch 5f7b51bf09ba ("netfilter: ipset: Limit the maximal range of
consecutive elements to add/delete") tried to fix it by limiting the max
elements to process at all. However it was not enough, it is still possible
that we get hung tasks. Lowering the limit is not reasonable, so the
approach in this patch is as follows: rely on the method used at resizing
sets and save the state when we reach a smaller internal batch limit,
unlock/lock and proceed from the saved state. Thus we can avoid long
continuous tasks and at the same time removed the limit to add/delete large
number of elements in one step.
The nfnl mutex is held during the whole operation which prevents one to
issue other ipset commands in parallel. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu-tasks: Avoid pr_info() with spin lock in cblist_init_generic()
pr_info() is called with rtp->cbs_gbl_lock spin lock locked. Because
pr_info() calls printk() that might sleep, this will result in BUG
like below:
[ 0.206455] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.206463]
[ 0.206464] =============================
[ 0.206464] [ BUG: Invalid wait context ]
[ 0.206465] 5.19.0-00428-g9de1f9c8ca51 #5 Not tainted
[ 0.206466] -----------------------------
[ 0.206466] swapper/0/1 is trying to lock:
[ 0.206467] ffffffffa0167a58 (&port_lock_key){....}-{3:3}, at: serial8250_console_write+0x327/0x4a0
[ 0.206473] other info that might help us debug this:
[ 0.206473] context-{5:5}
[ 0.206474] 3 locks held by swapper/0/1:
[ 0.206474] #0: ffffffff9eb597e0 (rcu_tasks.cbs_gbl_lock){....}-{2:2}, at: cblist_init_generic.constprop.0+0x14/0x1f0
[ 0.206478] #1: ffffffff9eb579c0 (console_lock){+.+.}-{0:0}, at: _printk+0x63/0x7e
[ 0.206482] #2: ffffffff9ea77780 (console_owner){....}-{0:0}, at: console_emit_next_record.constprop.0+0x111/0x330
[ 0.206485] stack backtrace:
[ 0.206486] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.19.0-00428-g9de1f9c8ca51 #5
[ 0.206488] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014
[ 0.206489] Call Trace:
[ 0.206490] <TASK>
[ 0.206491] dump_stack_lvl+0x6a/0x9f
[ 0.206493] __lock_acquire.cold+0x2d7/0x2fe
[ 0.206496] ? stack_trace_save+0x46/0x70
[ 0.206497] lock_acquire+0xd1/0x2f0
[ 0.206499] ? serial8250_console_write+0x327/0x4a0
[ 0.206500] ? __lock_acquire+0x5c7/0x2720
[ 0.206502] _raw_spin_lock_irqsave+0x3d/0x90
[ 0.206504] ? serial8250_console_write+0x327/0x4a0
[ 0.206506] serial8250_console_write+0x327/0x4a0
[ 0.206508] console_emit_next_record.constprop.0+0x180/0x330
[ 0.206511] console_unlock+0xf7/0x1f0
[ 0.206512] vprintk_emit+0xf7/0x330
[ 0.206514] _printk+0x63/0x7e
[ 0.206516] cblist_init_generic.constprop.0.cold+0x24/0x32
[ 0.206518] rcu_init_tasks_generic+0x5/0xd9
[ 0.206522] kernel_init_freeable+0x15b/0x2a2
[ 0.206523] ? rest_init+0x160/0x160
[ 0.206526] kernel_init+0x11/0x120
[ 0.206527] ret_from_fork+0x1f/0x30
[ 0.206530] </TASK>
[ 0.207018] cblist_init_generic: Setting shift to 1 and lim to 1.
This patch moves pr_info() so that it is called without
rtp->cbs_gbl_lock locked. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: check for station first in client probe
When probing a client, first check if we have it, and then
check for the channel context, otherwise you can trigger
the warning there easily by probing when the AP isn't even
started yet. Since a client existing means the AP is also
operating, we can then keep the warning.
Also simplify the moved code a bit. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: hyperv: avoid struct memcpy overrun warning
A previous patch addressed the fortified memcpy warning for most
builds, but I still see this one with gcc-9:
In file included from include/linux/string.h:254,
from drivers/hid/hid-hyperv.c:8:
In function 'fortify_memcpy_chk',
inlined from 'mousevsc_on_receive' at drivers/hid/hid-hyperv.c:272:3:
include/linux/fortify-string.h:583:4: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
583 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
My guess is that the WARN_ON() itself is what confuses gcc, so it no
longer sees that there is a correct range check. Rework the code in a
way that helps readability and avoids the warning. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/histograms: Add histograms to hist_vars if they have referenced variables
Hist triggers can have referenced variables without having direct
variables fields. This can be the case if referenced variables are added
for trigger actions. In this case the newly added references will not
have field variables. Not taking such referenced variables into
consideration can result in a bug where it would be possible to remove
hist trigger with variables being refenced. This will result in a bug
that is easily reproducable like so
$ cd /sys/kernel/tracing
$ echo 'synthetic_sys_enter char[] comm; long id' >> synthetic_events
$ echo 'hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger
$ echo 'hist:keys=common_pid.execname,id.syscall:onmatch(raw_syscalls.sys_enter).synthetic_sys_enter($comm, id)' >> events/raw_syscalls/sys_enter/trigger
$ echo '!hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger
[ 100.263533] ==================================================================
[ 100.264634] BUG: KASAN: slab-use-after-free in resolve_var_refs+0xc7/0x180
[ 100.265520] Read of size 8 at addr ffff88810375d0f0 by task bash/439
[ 100.266320]
[ 100.266533] CPU: 2 PID: 439 Comm: bash Not tainted 6.5.0-rc1 #4
[ 100.267277] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
[ 100.268561] Call Trace:
[ 100.268902] <TASK>
[ 100.269189] dump_stack_lvl+0x4c/0x70
[ 100.269680] print_report+0xc5/0x600
[ 100.270165] ? resolve_var_refs+0xc7/0x180
[ 100.270697] ? kasan_complete_mode_report_info+0x80/0x1f0
[ 100.271389] ? resolve_var_refs+0xc7/0x180
[ 100.271913] kasan_report+0xbd/0x100
[ 100.272380] ? resolve_var_refs+0xc7/0x180
[ 100.272920] __asan_load8+0x71/0xa0
[ 100.273377] resolve_var_refs+0xc7/0x180
[ 100.273888] event_hist_trigger+0x749/0x860
[ 100.274505] ? kasan_save_stack+0x2a/0x50
[ 100.275024] ? kasan_set_track+0x29/0x40
[ 100.275536] ? __pfx_event_hist_trigger+0x10/0x10
[ 100.276138] ? ksys_write+0xd1/0x170
[ 100.276607] ? do_syscall_64+0x3c/0x90
[ 100.277099] ? entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 100.277771] ? destroy_hist_data+0x446/0x470
[ 100.278324] ? event_hist_trigger_parse+0xa6c/0x3860
[ 100.278962] ? __pfx_event_hist_trigger_parse+0x10/0x10
[ 100.279627] ? __kasan_check_write+0x18/0x20
[ 100.280177] ? mutex_unlock+0x85/0xd0
[ 100.280660] ? __pfx_mutex_unlock+0x10/0x10
[ 100.281200] ? kfree+0x7b/0x120
[ 100.281619] ? ____kasan_slab_free+0x15d/0x1d0
[ 100.282197] ? event_trigger_write+0xac/0x100
[ 100.282764] ? __kasan_slab_free+0x16/0x20
[ 100.283293] ? __kmem_cache_free+0x153/0x2f0
[ 100.283844] ? sched_mm_cid_remote_clear+0xb1/0x250
[ 100.284550] ? __pfx_sched_mm_cid_remote_clear+0x10/0x10
[ 100.285221] ? event_trigger_write+0xbc/0x100
[ 100.285781] ? __kasan_check_read+0x15/0x20
[ 100.286321] ? __bitmap_weight+0x66/0xa0
[ 100.286833] ? _find_next_bit+0x46/0xe0
[ 100.287334] ? task_mm_cid_work+0x37f/0x450
[ 100.287872] event_triggers_call+0x84/0x150
[ 100.288408] trace_event_buffer_commit+0x339/0x430
[ 100.289073] ? ring_buffer_event_data+0x3f/0x60
[ 100.292189] trace_event_raw_event_sys_enter+0x8b/0xe0
[ 100.295434] syscall_trace_enter.constprop.0+0x18f/0x1b0
[ 100.298653] syscall_enter_from_user_mode+0x32/0x40
[ 100.301808] do_syscall_64+0x1a/0x90
[ 100.304748] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 100.307775] RIP: 0033:0x7f686c75c1cb
[ 100.310617] Code: 73 01 c3 48 8b 0d 65 3c 10 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 21 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 35 3c 10 00 f7 d8 64 89 01 48
[ 100.317847] RSP: 002b:00007ffc60137a38 EFLAGS: 00000246 ORIG_RAX: 0000000000000021
[ 100.321200] RA
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: base: Free devm resources when unregistering a device
In the current code, devres_release_all() only gets called if the device
has a bus and has been probed.
This leads to issues when using bus-less or driver-less devices where
the device might never get freed if a managed resource holds a reference
to the device. This is happening in the DRM framework for example.
We should thus call devres_release_all() in the device_del() function to
make sure that the device-managed actions are properly executed when the
device is unregistered, even if it has neither a bus nor a driver.
This is effectively the same change than commit 2f8d16a996da ("devres:
release resources on device_del()") that got reverted by commit
a525a3ddeaca ("driver core: free devres in device_release") over
memory leaks concerns.
This patch effectively combines the two commits mentioned above to
release the resources both on device_del() and device_release() and get
the best of both worlds. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa: Add max vqp attr to vdpa_nl_policy for nlattr length check
The vdpa_nl_policy structure is used to validate the nlattr when parsing
the incoming nlmsg. It will ensure the attribute being described produces
a valid nlattr pointer in info->attrs before entering into each handler
in vdpa_nl_ops.
That is to say, the missing part in vdpa_nl_policy may lead to illegal
nlattr after parsing, which could lead to OOB read just like CVE-2023-3773.
This patch adds the missing nla_policy for vdpa max vqp attr to avoid
such bugs. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: insert tree mod log move in push_node_left
There is a fairly unlikely race condition in tree mod log rewind that
can result in a kernel panic which has the following trace:
[530.569] BTRFS critical (device sda3): unable to find logical 0 length 4096
[530.585] BTRFS critical (device sda3): unable to find logical 0 length 4096
[530.602] BUG: kernel NULL pointer dereference, address: 0000000000000002
[530.618] #PF: supervisor read access in kernel mode
[530.629] #PF: error_code(0x0000) - not-present page
[530.641] PGD 0 P4D 0
[530.647] Oops: 0000 [#1] SMP
[530.654] CPU: 30 PID: 398973 Comm: below Kdump: loaded Tainted: G S O K 5.12.0-0_fbk13_clang_7455_gb24de3bdb045 #1
[530.680] Hardware name: Quanta Mono Lake-M.2 SATA 1HY9U9Z001G/Mono Lake-M.2 SATA, BIOS F20_3A15 08/16/2017
[530.703] RIP: 0010:__btrfs_map_block+0xaa/0xd00
[530.755] RSP: 0018:ffffc9002c2f7600 EFLAGS: 00010246
[530.767] RAX: ffffffffffffffea RBX: ffff888292e41000 RCX: f2702d8b8be15100
[530.784] RDX: ffff88885fda6fb8 RSI: ffff88885fd973c8 RDI: ffff88885fd973c8
[530.800] RBP: ffff888292e410d0 R08: ffffffff82fd7fd0 R09: 00000000fffeffff
[530.816] R10: ffffffff82e57fd0 R11: ffffffff82e57d70 R12: 0000000000000000
[530.832] R13: 0000000000001000 R14: 0000000000001000 R15: ffffc9002c2f76f0
[530.848] FS: 00007f38d64af000(0000) GS:ffff88885fd80000(0000) knlGS:0000000000000000
[530.866] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[530.880] CR2: 0000000000000002 CR3: 00000002b6770004 CR4: 00000000003706e0
[530.896] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[530.912] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[530.928] Call Trace:
[530.934] ? btrfs_printk+0x13b/0x18c
[530.943] ? btrfs_bio_counter_inc_blocked+0x3d/0x130
[530.955] btrfs_map_bio+0x75/0x330
[530.963] ? kmem_cache_alloc+0x12a/0x2d0
[530.973] ? btrfs_submit_metadata_bio+0x63/0x100
[530.984] btrfs_submit_metadata_bio+0xa4/0x100
[530.995] submit_extent_page+0x30f/0x360
[531.004] read_extent_buffer_pages+0x49e/0x6d0
[531.015] ? submit_extent_page+0x360/0x360
[531.025] btree_read_extent_buffer_pages+0x5f/0x150
[531.037] read_tree_block+0x37/0x60
[531.046] read_block_for_search+0x18b/0x410
[531.056] btrfs_search_old_slot+0x198/0x2f0
[531.066] resolve_indirect_ref+0xfe/0x6f0
[531.076] ? ulist_alloc+0x31/0x60
[531.084] ? kmem_cache_alloc_trace+0x12e/0x2b0
[531.095] find_parent_nodes+0x720/0x1830
[531.105] ? ulist_alloc+0x10/0x60
[531.113] iterate_extent_inodes+0xea/0x370
[531.123] ? btrfs_previous_extent_item+0x8f/0x110
[531.134] ? btrfs_search_path_in_tree+0x240/0x240
[531.146] iterate_inodes_from_logical+0x98/0xd0
[531.157] ? btrfs_search_path_in_tree+0x240/0x240
[531.168] btrfs_ioctl_logical_to_ino+0xd9/0x180
[531.179] btrfs_ioctl+0xe2/0x2eb0
This occurs when logical inode resolution takes a tree mod log sequence
number, and then while backref walking hits a rewind on a busy node
which has the following sequence of tree mod log operations (numbers
filled in from a specific example, but they are somewhat arbitrary)
REMOVE_WHILE_FREEING slot 532
REMOVE_WHILE_FREEING slot 531
REMOVE_WHILE_FREEING slot 530
...
REMOVE_WHILE_FREEING slot 0
REMOVE slot 455
REMOVE slot 454
REMOVE slot 453
...
REMOVE slot 0
ADD slot 455
ADD slot 454
ADD slot 453
...
ADD slot 0
MOVE src slot 0 -> dst slot 456 nritems 533
REMOVE slot 455
REMOVE slot 454
REMOVE slot 453
...
REMOVE slot 0
When this sequence gets applied via btrfs_tree_mod_log_rewind, it
allocates a fresh rewind eb, and first inserts the correct key info for
the 533 elements, then overwrites the first 456 of them, then decrements
the count by 456 via the add ops, then rewinds the move by doing a
memmove from 456:988->0:532. We have never written anything past 532,
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: u_serial: Add null pointer check in gserial_resume
Consider a case where gserial_disconnect has already cleared
gser->ioport. And if a wakeup interrupt triggers afterwards,
gserial_resume gets called, which will lead to accessing of
gser->ioport and thus causing null pointer dereference.Add
a null pointer check to prevent this.
Added a static spinlock to prevent gser->ioport from becoming
null after the newly added check. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix defrag path triggering jbd2 ASSERT
code path:
ocfs2_ioctl_move_extents
ocfs2_move_extents
ocfs2_defrag_extent
__ocfs2_move_extent
+ ocfs2_journal_access_di
+ ocfs2_split_extent //sub-paths call jbd2_journal_restart
+ ocfs2_journal_dirty //crash by jbs2 ASSERT
crash stacks:
PID: 11297 TASK: ffff974a676dcd00 CPU: 67 COMMAND: "defragfs.ocfs2"
#0 [ffffb25d8dad3900] machine_kexec at ffffffff8386fe01
#1 [ffffb25d8dad3958] __crash_kexec at ffffffff8395959d
#2 [ffffb25d8dad3a20] crash_kexec at ffffffff8395a45d
#3 [ffffb25d8dad3a38] oops_end at ffffffff83836d3f
#4 [ffffb25d8dad3a58] do_trap at ffffffff83833205
#5 [ffffb25d8dad3aa0] do_invalid_op at ffffffff83833aa6
#6 [ffffb25d8dad3ac0] invalid_op at ffffffff84200d18
[exception RIP: jbd2_journal_dirty_metadata+0x2ba]
RIP: ffffffffc09ca54a RSP: ffffb25d8dad3b70 RFLAGS: 00010207
RAX: 0000000000000000 RBX: ffff9706eedc5248 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffff97337029ea28 RDI: ffff9706eedc5250
RBP: ffff9703c3520200 R8: 000000000f46b0b2 R9: 0000000000000000
R10: 0000000000000001 R11: 00000001000000fe R12: ffff97337029ea28
R13: 0000000000000000 R14: ffff9703de59bf60 R15: ffff9706eedc5250
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffffb25d8dad3ba8] ocfs2_journal_dirty at ffffffffc137fb95 [ocfs2]
#8 [ffffb25d8dad3be8] __ocfs2_move_extent at ffffffffc139a950 [ocfs2]
#9 [ffffb25d8dad3c80] ocfs2_defrag_extent at ffffffffc139b2d2 [ocfs2]
Analysis
This bug has the same root cause of 'commit 7f27ec978b0e ("ocfs2: call
ocfs2_journal_access_di() before ocfs2_journal_dirty() in
ocfs2_write_end_nolock()")'. For this bug, jbd2_journal_restart() is
called by ocfs2_split_extent() during defragmenting.
How to fix
For ocfs2_split_extent() can handle journal operations totally by itself.
Caller doesn't need to call journal access/dirty pair, and caller only
needs to call journal start/stop pair. The fix method is to remove
journal access/dirty from __ocfs2_move_extent().
The discussion for this patch:
https://oss.oracle.com/pipermail/ocfs2-devel/2023-February/000647.html |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: Revert "scsi: core: Do not increase scsi_device's iorequest_cnt if dispatch failed"
The "atomic_inc(&cmd->device->iorequest_cnt)" in scsi_queue_rq() would
cause kernel panic because cmd->device may be freed after returning from
scsi_dispatch_cmd().
This reverts commit cfee29ffb45b1c9798011b19d454637d1b0fe87d. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Validate data run offset
This adds sanity checks for data run offset. We should make sure data
run offset is legit before trying to unpack them, otherwise we may
encounter use-after-free or some unexpected memory access behaviors.
[ 82.940342] BUG: KASAN: use-after-free in run_unpack+0x2e3/0x570
[ 82.941180] Read of size 1 at addr ffff888008a8487f by task mount/240
[ 82.941670]
[ 82.942069] CPU: 0 PID: 240 Comm: mount Not tainted 5.19.0+ #15
[ 82.942482] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 82.943720] Call Trace:
[ 82.944204] <TASK>
[ 82.944471] dump_stack_lvl+0x49/0x63
[ 82.944908] print_report.cold+0xf5/0x67b
[ 82.945141] ? __wait_on_bit+0x106/0x120
[ 82.945750] ? run_unpack+0x2e3/0x570
[ 82.946626] kasan_report+0xa7/0x120
[ 82.947046] ? run_unpack+0x2e3/0x570
[ 82.947280] __asan_load1+0x51/0x60
[ 82.947483] run_unpack+0x2e3/0x570
[ 82.947709] ? memcpy+0x4e/0x70
[ 82.947927] ? run_pack+0x7a0/0x7a0
[ 82.948158] run_unpack_ex+0xad/0x3f0
[ 82.948399] ? mi_enum_attr+0x14a/0x200
[ 82.948717] ? run_unpack+0x570/0x570
[ 82.949072] ? ni_enum_attr_ex+0x1b2/0x1c0
[ 82.949332] ? ni_fname_type.part.0+0xd0/0xd0
[ 82.949611] ? mi_read+0x262/0x2c0
[ 82.949970] ? ntfs_cmp_names_cpu+0x125/0x180
[ 82.950249] ntfs_iget5+0x632/0x1870
[ 82.950621] ? ntfs_get_block_bmap+0x70/0x70
[ 82.951192] ? evict+0x223/0x280
[ 82.951525] ? iput.part.0+0x286/0x320
[ 82.951969] ntfs_fill_super+0x1321/0x1e20
[ 82.952436] ? put_ntfs+0x1d0/0x1d0
[ 82.952822] ? vsprintf+0x20/0x20
[ 82.953188] ? mutex_unlock+0x81/0xd0
[ 82.953379] ? set_blocksize+0x95/0x150
[ 82.954001] get_tree_bdev+0x232/0x370
[ 82.954438] ? put_ntfs+0x1d0/0x1d0
[ 82.954700] ntfs_fs_get_tree+0x15/0x20
[ 82.955049] vfs_get_tree+0x4c/0x130
[ 82.955292] path_mount+0x645/0xfd0
[ 82.955615] ? putname+0x80/0xa0
[ 82.955955] ? finish_automount+0x2e0/0x2e0
[ 82.956310] ? kmem_cache_free+0x110/0x390
[ 82.956723] ? putname+0x80/0xa0
[ 82.957023] do_mount+0xd6/0xf0
[ 82.957411] ? path_mount+0xfd0/0xfd0
[ 82.957638] ? __kasan_check_write+0x14/0x20
[ 82.957948] __x64_sys_mount+0xca/0x110
[ 82.958310] do_syscall_64+0x3b/0x90
[ 82.958719] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 82.959341] RIP: 0033:0x7fd0d1ce948a
[ 82.960193] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008
[ 82.961532] RSP: 002b:00007ffe59ff69a8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5
[ 82.962527] RAX: ffffffffffffffda RBX: 0000564dcc107060 RCX: 00007fd0d1ce948a
[ 82.963266] RDX: 0000564dcc107260 RSI: 0000564dcc1072e0 RDI: 0000564dcc10fce0
[ 82.963686] RBP: 0000000000000000 R08: 0000564dcc107280 R09: 0000000000000020
[ 82.964272] R10: 00000000c0ed0000 R11: 0000000000000202 R12: 0000564dcc10fce0
[ 82.964785] R13: 0000564dcc107260 R14: 0000000000000000 R15: 00000000ffffffff |
| In the Linux kernel, the following vulnerability has been resolved:
null_blk: Always check queue mode setting from configfs
Make sure to check device queue mode in the null_validate_conf() and
return error for NULL_Q_RQ as we don't allow legacy I/O path, without
this patch we get OOPs when queue mode is set to 1 from configfs,
following are repro steps :-
modprobe null_blk nr_devices=0
mkdir config/nullb/nullb0
echo 1 > config/nullb/nullb0/memory_backed
echo 4096 > config/nullb/nullb0/blocksize
echo 20480 > config/nullb/nullb0/size
echo 1 > config/nullb/nullb0/queue_mode
echo 1 > config/nullb/nullb0/power
Entering kdb (current=0xffff88810acdd080, pid 2372) on processor 42 Oops: (null)
due to oops @ 0xffffffffc041c329
CPU: 42 PID: 2372 Comm: sh Tainted: G O N 6.3.0-rc5lblk+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
RIP: 0010:null_add_dev.part.0+0xd9/0x720 [null_blk]
Code: 01 00 00 85 d2 0f 85 a1 03 00 00 48 83 bb 08 01 00 00 00 0f 85 f7 03 00 00 80 bb 62 01 00 00 00 48 8b 75 20 0f 85 6d 02 00 00 <48> 89 6e 60 48 8b 75 20 bf 06 00 00 00 e8 f5 37 2c c1 48 8b 75 20
RSP: 0018:ffffc900052cbde0 EFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff88811084d800 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888100042e00
RBP: ffff8881053d8200 R08: ffffc900052cbd68 R09: ffff888105db2000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000002
R13: ffff888104765200 R14: ffff88810eec1748 R15: ffff88810eec1740
FS: 00007fd445fd1740(0000) GS:ffff8897dfc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000060 CR3: 0000000166a00000 CR4: 0000000000350ee0
DR0: ffffffff8437a488 DR1: ffffffff8437a489 DR2: ffffffff8437a48a
DR3: ffffffff8437a48b DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
nullb_device_power_store+0xd1/0x120 [null_blk]
configfs_write_iter+0xb4/0x120
vfs_write+0x2ba/0x3c0
ksys_write+0x5f/0xe0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7fd4460c57a7
Code: 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:00007ffd3792a4a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd4460c57a7
RDX: 0000000000000002 RSI: 000055b43c02e4c0 RDI: 0000000000000001
RBP: 000055b43c02e4c0 R08: 000000000000000a R09: 00007fd44615b4e0
R10: 00007fd44615b3e0 R11: 0000000000000246 R12: 0000000000000002
R13: 00007fd446198520 R14: 0000000000000002 R15: 00007fd446198700
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
When CPU 0 is offline and intel_powerclamp is used to inject
idle, it generates kernel BUG:
BUG: using smp_processor_id() in preemptible [00000000] code: bash/15687
caller is debug_smp_processor_id+0x17/0x20
CPU: 4 PID: 15687 Comm: bash Not tainted 5.19.0-rc7+ #57
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x63
dump_stack+0x10/0x16
check_preemption_disabled+0xdd/0xe0
debug_smp_processor_id+0x17/0x20
powerclamp_set_cur_state+0x7f/0xf9 [intel_powerclamp]
...
...
Here CPU 0 is the control CPU by default and changed to the current CPU,
if CPU 0 offlined. This check has to be performed under cpus_read_lock(),
hence the above warning.
Use get_cpu() instead of smp_processor_id() to avoid this BUG.
[ rjw: Subject edits ] |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix deadlock in tc route query code
Cited commit causes ABBA deadlock[0] when peer flows are created while
holding the devcom rw semaphore. Due to peer flows offload implementation
the lock is taken much higher up the call chain and there is no obvious way
to easily fix the deadlock. Instead, since tc route query code needs the
peer eswitch structure only to perform a lookup in xarray and doesn't
perform any sleeping operations with it, refactor the code for lockless
execution in following ways:
- RCUify the devcom 'data' pointer. When resetting the pointer
synchronously wait for RCU grace period before returning. This is fine
since devcom is currently only used for synchronization of
pairing/unpairing of eswitches which is rare and already expensive as-is.
- Wrap all usages of 'paired' boolean in {READ|WRITE}_ONCE(). The flag has
already been used in some unlocked contexts without proper
annotations (e.g. users of mlx5_devcom_is_paired() function), but it wasn't
an issue since all relevant code paths checked it again after obtaining the
devcom semaphore. Now it is also used by mlx5_devcom_get_peer_data_rcu() as
"best effort" check to return NULL when devcom is being unpaired. Note that
while RCU read lock doesn't prevent the unpaired flag from being changed
concurrently it still guarantees that reader can continue to use 'data'.
- Refactor mlx5e_tc_query_route_vport() function to use new
mlx5_devcom_get_peer_data_rcu() API which fixes the deadlock.
[0]:
[ 164.599612] ======================================================
[ 164.600142] WARNING: possible circular locking dependency detected
[ 164.600667] 6.3.0-rc3+ #1 Not tainted
[ 164.601021] ------------------------------------------------------
[ 164.601557] handler1/3456 is trying to acquire lock:
[ 164.601998] ffff88811f1714b0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}, at: mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[ 164.603078]
but task is already holding lock:
[ 164.603617] ffff88810137fc98 (&comp->sem){++++}-{3:3}, at: mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core]
[ 164.604459]
which lock already depends on the new lock.
[ 164.605190]
the existing dependency chain (in reverse order) is:
[ 164.605848]
-> #1 (&comp->sem){++++}-{3:3}:
[ 164.606380] down_read+0x39/0x50
[ 164.606772] mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core]
[ 164.607336] mlx5e_tc_query_route_vport+0x86/0xc0 [mlx5_core]
[ 164.607914] mlx5e_tc_tun_route_lookup+0x1a4/0x1d0 [mlx5_core]
[ 164.608495] mlx5e_attach_decap_route+0xc6/0x1e0 [mlx5_core]
[ 164.609063] mlx5e_tc_add_fdb_flow+0x1ea/0x360 [mlx5_core]
[ 164.609627] __mlx5e_add_fdb_flow+0x2d2/0x430 [mlx5_core]
[ 164.610175] mlx5e_configure_flower+0x952/0x1a20 [mlx5_core]
[ 164.610741] tc_setup_cb_add+0xd4/0x200
[ 164.611146] fl_hw_replace_filter+0x14c/0x1f0 [cls_flower]
[ 164.611661] fl_change+0xc95/0x18a0 [cls_flower]
[ 164.612116] tc_new_tfilter+0x3fc/0xd20
[ 164.612516] rtnetlink_rcv_msg+0x418/0x5b0
[ 164.612936] netlink_rcv_skb+0x54/0x100
[ 164.613339] netlink_unicast+0x190/0x250
[ 164.613746] netlink_sendmsg+0x245/0x4a0
[ 164.614150] sock_sendmsg+0x38/0x60
[ 164.614522] ____sys_sendmsg+0x1d0/0x1e0
[ 164.614934] ___sys_sendmsg+0x80/0xc0
[ 164.615320] __sys_sendmsg+0x51/0x90
[ 164.615701] do_syscall_64+0x3d/0x90
[ 164.616083] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 164.616568]
-> #0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}:
[ 164.617210] __lock_acquire+0x159e/0x26e0
[ 164.617638] lock_acquire+0xc2/0x2a0
[ 164.618018] __mutex_lock+0x92/0xcd0
[ 164.618401] mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[ 164.618943] post_process_attr+0x153/0x2d0 [
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Check for NOT_READY flag state after locking
Currently the check for NOT_READY flag is performed before obtaining the
necessary lock. This opens a possibility for race condition when the flow
is concurrently removed from unready_flows list by the workqueue task,
which causes a double-removal from the list and a crash[0]. Fix the issue
by moving the flag check inside the section protected by
uplink_priv->unready_flows_lock mutex.
[0]:
[44376.389654] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP
[44376.391665] CPU: 7 PID: 59123 Comm: tc Not tainted 6.4.0-rc4+ #1
[44376.392984] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[44376.395342] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.396857] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06
[44376.399167] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246
[44376.399680] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00
[44376.400337] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0
[44376.401001] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001
[44376.401663] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000
[44376.402342] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000
[44376.402999] FS: 00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000
[44376.403787] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44376.404343] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0
[44376.405004] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[44376.405665] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[44376.406339] Call Trace:
[44376.406651] <TASK>
[44376.406939] ? die_addr+0x33/0x90
[44376.407311] ? exc_general_protection+0x192/0x390
[44376.407795] ? asm_exc_general_protection+0x22/0x30
[44376.408292] ? mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.408876] __mlx5e_tc_del_fdb_peer_flow+0xbc/0xe0 [mlx5_core]
[44376.409482] mlx5e_tc_del_flow+0x42/0x210 [mlx5_core]
[44376.410055] mlx5e_flow_put+0x25/0x50 [mlx5_core]
[44376.410529] mlx5e_delete_flower+0x24b/0x350 [mlx5_core]
[44376.411043] tc_setup_cb_reoffload+0x22/0x80
[44376.411462] fl_reoffload+0x261/0x2f0 [cls_flower]
[44376.411907] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.412481] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.413044] tcf_block_playback_offloads+0x76/0x170
[44376.413497] tcf_block_unbind+0x7b/0xd0
[44376.413881] tcf_block_setup+0x17d/0x1c0
[44376.414269] tcf_block_offload_cmd.isra.0+0xf1/0x130
[44376.414725] tcf_block_offload_unbind+0x43/0x70
[44376.415153] __tcf_block_put+0x82/0x150
[44376.415532] ingress_destroy+0x22/0x30 [sch_ingress]
[44376.415986] qdisc_destroy+0x3b/0xd0
[44376.416343] qdisc_graft+0x4d0/0x620
[44376.416706] tc_get_qdisc+0x1c9/0x3b0
[44376.417074] rtnetlink_rcv_msg+0x29c/0x390
[44376.419978] ? rep_movs_alternative+0x3a/0xa0
[44376.420399] ? rtnl_calcit.isra.0+0x120/0x120
[44376.420813] netlink_rcv_skb+0x54/0x100
[44376.421192] netlink_unicast+0x1f6/0x2c0
[44376.421573] netlink_sendmsg+0x232/0x4a0
[44376.421980] sock_sendmsg+0x38/0x60
[44376.422328] ____sys_sendmsg+0x1d0/0x1e0
[44376.422709] ? copy_msghdr_from_user+0x6d/0xa0
[44376.423127] ___sys_sendmsg+0x80/0xc0
[44376.423495] ? ___sys_recvmsg+0x8b/0xc0
[44376.423869] __sys_sendmsg+0x51/0x90
[44376.424226] do_syscall_64+0x3d/0x90
[44376.424587] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[44376.425046] RIP: 0033:0x7f045134f887
[44376.425403] Code: 0a 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00
---truncated--- |
