| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use pskb_network_may_pull() in route_shortcircuit()
route_shortcircuit() currently calls pskb_may_pull(skb, sizeof(struct iphdr))
(or ipv6hdr), which checks if bytes are available starting from skb->data.
However, in vxlan_xmit(), skb->data points to the MAC header, so
skb_network_offset(skb) is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, 20)
only checks 20 bytes from skb->data (which is 14 bytes MAC header + 6 bytes of
IP header), leaving the rest of the IP header potentially un-pulled in non-linear
frags. Subsequent dereferences of ip_hdr(skb)->daddr can read beyond the pulled
linear buffer length.
Fix this by using pskb_network_may_pull(), which adds skb_network_offset(skb) to
the length check to ensure the full network header is present in the linear buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: reset kernel-owned dev_info fields in ublk_ctrl_add_dev()
ublk_ctrl_add_dev() memcpy()s the userspace ublksrv_ctrl_dev_info into
ub->dev_info and then fixes up the fields the driver owns, but misses
->state and ->ublksrv_pid.
A device added with ->state = UBLK_S_DEV_LIVE passes the
"->state != UBLK_S_DEV_DEAD" test that ublk_stop_dev_unlocked() uses as its
proxy for "a disk is attached", while ->ub_disk is still NULL, so DEL_DEV
right after ADD_DEV oopses in del_gendisk(). UBLK_S_DEV_QUIESCED plus
UBLK_F_USER_RECOVERY dies one step earlier, in ublk_force_abort_dev(). A
poisoned ->state also gets START_USER_RECOVERY and the char device
read/write path onto a device that was never started, and wedges START_DEV
at -EEXIST. A poisoned ->ublksrv_pid just makes GET_DEV_INFO report an
unrelated task as the ublk server.
Reset both after the memcpy(), as ublk_detach_disk() does. Userspace only
ever reads these back, so correcting them silently breaks nothing.
ADD_DEV has copied ->state in unsanitized since ublk was merged, but back
then it was harmless: the gendisk was allocated during ADD_DEV, and both
teardown and the START_DEV -EEXIST check keyed off disk_live() rather than
->state. The oops became reachable once the disk allocation moved to
START_DEV and those checks switched to ->state. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: validate DRAW_PRIMITIVES header size before division
vmw_cmd_draw() computes
maxnum = (header->size - sizeof(cmd->body)) / sizeof(*decl);
where header->size is u32 and is taken straight from the user-supplied
command stream. When header->size is less than sizeof(cmd->body) the
unsigned subtraction wraps to nearly 4 GiB, producing a huge maxnum.
Any user-controlled cmd->body.numVertexDecls then passes the bound and
the loop dereferences decl[i] far past the end of the kernel command
bounce buffer, producing an out-of-bounds read of kernel memory.
Reject undersized headers up front. |
| In Modem, there is a possible out of bounds read due to a missing bounds check. This could lead to remote denial of service, if a UE has connected to a rogue base station controlled by the attacker, with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: MOLY00741071; Issue ID: MSV-7620. |
| In display, there is a possible information disclosure due to a missing bounds check. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11004276; Issue ID: MSV-7757. |
| In display, there is a possible information disclosure due to an integer overflow. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11004274; Issue ID: MSV-7749. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an out-of-bounds read. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to obtain sensitive information or cause a denial of service due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Prevent access to unsupported weight registers
Sashiko reports:
During initialization of the nct6116 chip, the driver sets data->pwm_num
to 5. However, it assigns several NCT6106 register arrays (such as
NCT6106_REG_WEIGHT_DUTY_STEP, NCT6106_REG_WEIGHT_TEMP_SEL, and
NCT6106_REG_WEIGHT_TEMP_*) to data->REG_PWM and data->REG_WEIGHT_TEMP.
These arrays only contain 3 elements.
In nct6775_update_pwm(), the driver iterates up to data->pwm_num. If
data->has_pwm has bits 3 or 4 set (which is structurally possible for
nct6116), the loop attempts to read elements at index 3 and 4 from these
3-element arrays. This results in a global out-of-bounds read, which can
be caught by KASAN.
Furthermore, the driver uses these garbage out-of-bounds values as
hardware register addresses for subsequent read and write operations. This
leads to invalid hardware register access, potentially causing hardware
misconfiguration or system crashes.
The underlying problem is that the chip does support up to five fan
control channels, but only the first three support weight control.
Fix the problem by extending the affected weight register arrays with
zeroed fields. The driver uses zeroed register addresses to determine
if a register is supported or not, and skips accesses for unsupported
registers. |
| In the Linux kernel, the following vulnerability has been resolved:
macsec: don't read an unset MAC header in macsec_encrypt()
macsec_encrypt() reads the Ethernet header via eth_hdr(skb)
(skb->head + skb->mac_header) to memmove() the 12 source/destination MAC
bytes forward and make room for the SecTAG.
On the AF_PACKET SOCK_RAW + PACKET_QDISC_BYPASS transmit path the skb
reaches the macsec ndo_start_xmit() with the MAC header unset, so
eth_hdr(skb) resolves to skb->head + (u16)~0 and the read is out of
bounds: a 12-byte heap over-read that is also emitted on the wire as the
frame's outer source/destination MAC. KASAN reports a slab-out-of-bounds
read in macsec_start_xmit() on 6.0; on current mainline a CONFIG_DEBUG_NET
build flags it as an unset mac header in skb_mac_header().
On the TX path the L2 header is at skb->data, so use skb_eth_hdr(), added
by commit 96cc4b69581d ("macvlan: do not assume mac_header is set in
macvlan_broadcast()") for exactly this purpose. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an off-by-one error in bounds checking. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: bound get_version reply decode to front len
handle_get_version_reply() uses msg->front_alloc_len as the decode
boundary for MON_GET_VERSION_REPLY. That is the size of the reused
reply buffer, not the number of bytes actually received.
A truncated reply can therefore pass ceph_decode_need() and decode the
second u64 from stale tail bytes left in the buffer by an earlier
message, causing an uninitialized memory read.
Use msg->front.iov_len as the receive-side decode boundary, matching
other libceph reply handlers and limiting decoding to the bytes that
were actually read from the wire. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to obtain sensitive information due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: bound element ID read when checking non-inheritance
cfg80211_is_element_inherited() reads the first data octet of the
candidate element (id = elem->data[0]) to look it up in an extension
non-inheritance list. It does so after testing elem->id, but without
verifying that the element actually has a data octet. A zero-length
extension element (WLAN_EID_EXTENSION with length 0) therefore makes it
read one octet past the end of the element.
_ieee802_11_parse_elems_full() runs this check for every element of a
frame once a non-inheritance context exists -- e.g. while parsing a
per-STA profile of a Multi-Link element in a (re)association response,
or a non-transmitted BSS profile -- so a crafted frame from an AP can
trigger a one-octet slab-out-of-bounds read during element parsing:
BUG: KASAN: slab-out-of-bounds in cfg80211_is_element_inherited
Read of size 1 ... in net/wireless/scan.c
Return early (treat the element as inherited) when an extension element
carries no data, mirroring the existing handling of empty ID lists.
The bug was found by fuzzing ieee802_11_parse_elems_full() under KASAN. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: at76c50x-usb: avoid length underflow in at76_guess_freq()
at76_guess_freq() checks only that the received frame is at least a bare
802.11 header (24 bytes) before subtracting the fixed management-body
offset:
len -= el_off;
For both beacon and probe response frames, el_off is 36. If the frame is
shorter than el_off, subtracting it causes the calculated IE length to
wrap. The length is eventually passed to cfg80211_find_elem_match() as a
very large unsigned value, so the element walk runs beyond the RX skb.
This path is reached from at76_rx_tasklet() while scanning. If the device
delivers a truncated beacon or probe response, the oversized IE length
causes an out-of-bounds read during scanning.
Skip the IE lookup if the frame does not reach the variable elements,
before subtracting el_off. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_ncm: validate datagram bounds in ncm_unwrap_ntb()
When unpacking host-supplied NTBs, ncm_unwrap_ntb() checks datagram length
against frame_max but does not verify that the datagram fits within the
declared block length. Additionally, when decoding multiple NTBs from a
single socket buffer, subsequent block lengths are not checked against the
actual remaining buffer data.
With these checks missing, a malicious USB host can specify datagram
offsets and lengths that point beyond the block, or supply secondary NTB
headers declaring lengths larger than the buffer. skb_put_data() then
copies adjacent kernel memory from skb_shared_info into the network skb.
Fix this by verifying that sufficient buffer space remains for the NTB
header before parsing, handling zero-length block declarations, ensuring
that block lengths never exceed the remaining buffer space, and verifying
that each datagram payload stays strictly within the block boundary. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uvc: clamp SEND_RESPONSE length to the response buffer
uvc_send_response() builds the UVC control response from a user-supplied
struct uvc_request_data:
req->length = min_t(unsigned int, uvc->event_length, data->length);
...
memcpy(req->buf, data->data, req->length);
req->length is clamped to uvc->event_length, which is taken from the
host control request wLength (up to UVC_MAX_REQUEST_SIZE, 64), and to
data->length, which comes from the UVCIOC_SEND_RESPONSE ioctl and is
only checked for being negative. The source buffer data->data is only
60 bytes, so a response with uvc->event_length and data->length both
greater than 60 makes memcpy() read past the end of data->data.
Clamp req->length to sizeof(data->data) as well. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: fix OOB read from firmware num_msg in TX complete handler
The firmware-controlled num_msg field (u8, 0-255) drives the loop in
ath6kl_wmi_tx_complete_event_rx() without validation against the buffer
length. This allows out-of-bounds reads of up to 1020 bytes past the
WMI event buffer when the firmware sends an inflated num_msg.
Add a check that the buffer is large enough to hold the fixed struct
and the num_msg variable-length entries. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: carl9170: bound memcpy length in cmd callback to prevent OOB read
When the firmware sends a command response with a length mismatch,
carl9170_cmd_callback() logs the mismatch and calls carl9170_restart()
but then falls through to memcpy(ar->readbuf, buffer + 4, len - 4).
Since len comes from the firmware and can exceed ar->readlen, this
copies more data than the readbuf was allocated for.
Bound the memcpy to min(len - 4, ar->readlen) so that the response
is still completed -- avoiding repeated restarts from queued garbage --
while preventing an overread past the response buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: carl9170: fix OOB read from off-by-two in TX status handler
The bounds check in carl9170_tx_process_status() uses
`i > ((cmd->hdr.len / 2) + 1)` which is off by two, allowing
2 extra iterations past valid _tx_status entries when the firmware-
controlled hdr.ext exceeds hdr.len/2. Fix by using the correct
comparison `i >= (cmd->hdr.len / 2)`. |
