| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: fix folio is still mapped when deleted
Migration may be raced with fallocating hole. remove_inode_single_folio
will unmap the folio if the folio is still mapped. However, it's called
without folio lock. If the folio is migrated and the mapped pte has been
converted to migration entry, folio_mapped() returns false, and won't
unmap it. Due to extra refcount held by remove_inode_single_folio,
migration fails, restores migration entry to normal pte, and the folio is
mapped again. As a result, we triggered BUG in filemap_unaccount_folio.
The log is as follows:
BUG: Bad page cache in process hugetlb pfn:156c00
page: refcount:515 mapcount:0 mapping:0000000099fef6e1 index:0x0 pfn:0x156c00
head: order:9 mapcount:1 entire_mapcount:1 nr_pages_mapped:0 pincount:0
aops:hugetlbfs_aops ino:dcc dentry name(?):"my_hugepage_file"
flags: 0x17ffffc00000c1(locked|waiters|head|node=0|zone=2|lastcpupid=0x1fffff)
page_type: f4(hugetlb)
page dumped because: still mapped when deleted
CPU: 1 UID: 0 PID: 395 Comm: hugetlb Not tainted 6.17.0-rc5-00044-g7aac71907bde-dirty #484 NONE
Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x4f/0x70
filemap_unaccount_folio+0xc4/0x1c0
__filemap_remove_folio+0x38/0x1c0
filemap_remove_folio+0x41/0xd0
remove_inode_hugepages+0x142/0x250
hugetlbfs_fallocate+0x471/0x5a0
vfs_fallocate+0x149/0x380
Hold folio lock before checking if the folio is mapped to avold race with
migration. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: uas: fix urb unmapping issue when the uas device is remove during ongoing data transfer
When a UAS device is unplugged during data transfer, there is
a probability of a system panic occurring. The root cause is
an access to an invalid memory address during URB callback handling.
Specifically, this happens when the dma_direct_unmap_sg() function
is called within the usb_hcd_unmap_urb_for_dma() interface, but the
sg->dma_address field is 0 and the sg data structure has already been
freed.
The SCSI driver sends transfer commands by invoking uas_queuecommand_lck()
in uas.c, using the uas_submit_urbs() function to submit requests to USB.
Within the uas_submit_urbs() implementation, three URBs (sense_urb,
data_urb, and cmd_urb) are sequentially submitted. Device removal may
occur at any point during uas_submit_urbs execution, which may result
in URB submission failure. However, some URBs might have been successfully
submitted before the failure, and uas_submit_urbs will return the -ENODEV
error code in this case. The current error handling directly calls
scsi_done(). In the SCSI driver, this eventually triggers scsi_complete()
to invoke scsi_end_request() for releasing the sgtable. The successfully
submitted URBs, when being unlinked to giveback, call
usb_hcd_unmap_urb_for_dma() in hcd.c, leading to exceptions during sg
unmapping operations since the sg data structure has already been freed.
This patch modifies the error condition check in the uas_submit_urbs()
function. When a UAS device is removed but one or more URBs have already
been successfully submitted to USB, it avoids immediately invoking
scsi_done() and save the cmnd to devinfo->cmnd array. If the successfully
submitted URBs is completed before devinfo->resetting being set, then
the scsi_done() function will be called within uas_try_complete() after
all pending URB operations are finalized. Otherwise, the scsi_done()
function will be called within uas_zap_pending(), which is executed after
usb_kill_anchored_urbs().
The error handling only takes effect when uas_queuecommand_lck() calls
uas_submit_urbs() and returns the error value -ENODEV . In this case,
the device is disconnected, and the flow proceeds to uas_disconnect(),
where uas_zap_pending() is invoked to call uas_try_complete(). |
| In the Linux kernel, the following vulnerability has been resolved:
md: init bioset in mddev_init
IO operations may be needed before md_run(), such as updating metadata
after writing sysfs. Without bioset, this triggers a NULL pointer
dereference as below:
BUG: kernel NULL pointer dereference, address: 0000000000000020
Call Trace:
md_update_sb+0x658/0xe00
new_level_store+0xc5/0x120
md_attr_store+0xc9/0x1e0
sysfs_kf_write+0x6f/0xa0
kernfs_fop_write_iter+0x141/0x2a0
vfs_write+0x1fc/0x5a0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x2818/0x2880
do_syscall_64+0xa9/0x580
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Reproducer
```
mdadm -CR /dev/md0 -l1 -n2 /dev/sd[cd]
echo inactive > /sys/block/md0/md/array_state
echo 10 > /sys/block/md0/md/new_level
```
mddev_init() can only be called once per mddev, no need to test if bioset
has been initialized anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-fc: move lsop put work to nvmet_fc_ls_req_op
It’s possible for more than one async command to be in flight from
__nvmet_fc_send_ls_req. For each command, a tgtport reference is taken.
In the current code, only one put work item is queued at a time, which
results in a leaked reference.
To fix this, move the work item to the nvmet_fc_ls_req_op struct, which
already tracks all resources related to the command. |
| In the Linux kernel, the following vulnerability has been resolved:
md: fix rcu protection in md_wakeup_thread
We attempted to use RCU to protect the pointer 'thread', but directly
passed the value when calling md_wakeup_thread(). This means that the
RCU pointer has been acquired before rcu_read_lock(), which renders
rcu_read_lock() ineffective and could lead to a use-after-free. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: essiv - Check ssize for decryption and in-place encryption
Move the ssize check to the start in essiv_aead_crypt so that
it's also checked for decryption and in-place encryption. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix null deref on srq->rq.queue after resize failure
A NULL pointer dereference can occur in rxe_srq_chk_attr() when
ibv_modify_srq() is invoked twice in succession under certain error
conditions. The first call may fail in rxe_queue_resize(), which leads
rxe_srq_from_attr() to set srq->rq.queue = NULL. The second call then
triggers a crash (null deref) when accessing
srq->rq.queue->buf->index_mask.
Call Trace:
<TASK>
rxe_modify_srq+0x170/0x480 [rdma_rxe]
? __pfx_rxe_modify_srq+0x10/0x10 [rdma_rxe]
? uverbs_try_lock_object+0x4f/0xa0 [ib_uverbs]
? rdma_lookup_get_uobject+0x1f0/0x380 [ib_uverbs]
ib_uverbs_modify_srq+0x204/0x290 [ib_uverbs]
? __pfx_ib_uverbs_modify_srq+0x10/0x10 [ib_uverbs]
? tryinc_node_nr_active+0xe6/0x150
? uverbs_fill_udata+0xed/0x4f0 [ib_uverbs]
ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0x2c0/0x470 [ib_uverbs]
? __pfx_ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0x10/0x10 [ib_uverbs]
? uverbs_fill_udata+0xed/0x4f0 [ib_uverbs]
ib_uverbs_run_method+0x55a/0x6e0 [ib_uverbs]
? __pfx_ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0x10/0x10 [ib_uverbs]
ib_uverbs_cmd_verbs+0x54d/0x800 [ib_uverbs]
? __pfx_ib_uverbs_cmd_verbs+0x10/0x10 [ib_uverbs]
? __pfx___raw_spin_lock_irqsave+0x10/0x10
? __pfx_do_vfs_ioctl+0x10/0x10
? ioctl_has_perm.constprop.0.isra.0+0x2c7/0x4c0
? __pfx_ioctl_has_perm.constprop.0.isra.0+0x10/0x10
ib_uverbs_ioctl+0x13e/0x220 [ib_uverbs]
? __pfx_ib_uverbs_ioctl+0x10/0x10 [ib_uverbs]
__x64_sys_ioctl+0x138/0x1c0
do_syscall_64+0x82/0x250
? fdget_pos+0x58/0x4c0
? ksys_write+0xf3/0x1c0
? __pfx_ksys_write+0x10/0x10
? do_syscall_64+0xc8/0x250
? __pfx_vm_mmap_pgoff+0x10/0x10
? fget+0x173/0x230
? fput+0x2a/0x80
? ksys_mmap_pgoff+0x224/0x4c0
? do_syscall_64+0xc8/0x250
? do_user_addr_fault+0x37b/0xfe0
? clear_bhb_loop+0x50/0xa0
? clear_bhb_loop+0x50/0xa0
? clear_bhb_loop+0x50/0xa0
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: Fix uninit buffer allocated by __getname()
Fix uninit errors caused after buffer allocation given to 'de'; by
initializing the buffer with zeroes. The fix was found by using KMSAN. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: fix ipv4 null-ptr-deref in route error path
The IPv4 code path in __ip_vs_get_out_rt() calls dst_link_failure()
without ensuring skb->dev is set, leading to a NULL pointer dereference
in fib_compute_spec_dst() when ipv4_link_failure() attempts to send
ICMP destination unreachable messages.
The issue emerged after commit ed0de45a1008 ("ipv4: recompile ip options
in ipv4_link_failure") started calling __ip_options_compile() from
ipv4_link_failure(). This code path eventually calls fib_compute_spec_dst()
which dereferences skb->dev. An attempt was made to fix the NULL skb->dev
dereference in commit 0113d9c9d1cc ("ipv4: fix null-deref in
ipv4_link_failure"), but it only addressed the immediate dev_net(skb->dev)
dereference by using a fallback device. The fix was incomplete because
fib_compute_spec_dst() later in the call chain still accesses skb->dev
directly, which remains NULL when IPVS calls dst_link_failure().
The crash occurs when:
1. IPVS processes a packet in NAT mode with a misconfigured destination
2. Route lookup fails in __ip_vs_get_out_rt() before establishing a route
3. The error path calls dst_link_failure(skb) with skb->dev == NULL
4. ipv4_link_failure() → ipv4_send_dest_unreach() →
__ip_options_compile() → fib_compute_spec_dst()
5. fib_compute_spec_dst() dereferences NULL skb->dev
Apply the same fix used for IPv6 in commit 326bf17ea5d4 ("ipvs: fix
ipv6 route unreach panic"): set skb->dev from skb_dst(skb)->dev before
calling dst_link_failure().
KASAN: null-ptr-deref in range [0x0000000000000328-0x000000000000032f]
CPU: 1 PID: 12732 Comm: syz.1.3469 Not tainted 6.6.114 #2
RIP: 0010:__in_dev_get_rcu include/linux/inetdevice.h:233
RIP: 0010:fib_compute_spec_dst+0x17a/0x9f0 net/ipv4/fib_frontend.c:285
Call Trace:
<TASK>
spec_dst_fill net/ipv4/ip_options.c:232
spec_dst_fill net/ipv4/ip_options.c:229
__ip_options_compile+0x13a1/0x17d0 net/ipv4/ip_options.c:330
ipv4_send_dest_unreach net/ipv4/route.c:1252
ipv4_link_failure+0x702/0xb80 net/ipv4/route.c:1265
dst_link_failure include/net/dst.h:437
__ip_vs_get_out_rt+0x15fd/0x19e0 net/netfilter/ipvs/ip_vs_xmit.c:412
ip_vs_nat_xmit+0x1d8/0xc80 net/netfilter/ipvs/ip_vs_xmit.c:764 |
| In the Linux kernel, the following vulnerability has been resolved:
can: hi311x: populate ndo_change_mtu() to prevent buffer overflow
Sending an PF_PACKET allows to bypass the CAN framework logic and to
directly reach the xmit() function of a CAN driver. The only check
which is performed by the PF_PACKET framework is to make sure that
skb->len fits the interface's MTU.
Unfortunately, because the sun4i_can driver does not populate its
net_device_ops->ndo_change_mtu(), it is possible for an attacker to
configure an invalid MTU by doing, for example:
$ ip link set can0 mtu 9999
After doing so, the attacker could open a PF_PACKET socket using the
ETH_P_CANXL protocol:
socket(PF_PACKET, SOCK_RAW, htons(ETH_P_CANXL))
to inject a malicious CAN XL frames. For example:
struct canxl_frame frame = {
.flags = 0xff,
.len = 2048,
};
The CAN drivers' xmit() function are calling can_dev_dropped_skb() to
check that the skb is valid, unfortunately under above conditions, the
malicious packet is able to go through can_dev_dropped_skb() checks:
1. the skb->protocol is set to ETH_P_CANXL which is valid (the
function does not check the actual device capabilities).
2. the length is a valid CAN XL length.
And so, hi3110_hard_start_xmit() receives a CAN XL frame which it is
not able to correctly handle and will thus misinterpret it as a CAN
frame. The driver will consume frame->len as-is with no further
checks.
This can result in a buffer overflow later on in hi3110_hw_tx() on
this line:
memcpy(buf + HI3110_FIFO_EXT_DATA_OFF,
frame->data, frame->len);
Here, frame->len corresponds to the flags field of the CAN XL frame.
In our previous example, we set canxl_frame->flags to 0xff. Because
the maximum expected length is 8, a buffer overflow of 247 bytes
occurs!
Populate net_device_ops->ndo_change_mtu() to ensure that the
interface's MTU can not be set to anything bigger than CAN_MTU. By
fixing the root cause, this prevents the buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
smack: fix bug: unprivileged task can create labels
If an unprivileged task is allowed to relabel itself
(/smack/relabel-self is not empty),
it can freely create new labels by writing their
names into own /proc/PID/attr/smack/current
This occurs because do_setattr() imports
the provided label in advance,
before checking "relabel-self" list.
This change ensures that the "relabel-self" list
is checked before importing the label. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix improper freeing of purex item
In qla2xxx_process_purls_iocb(), an item is allocated via
qla27xx_copy_multiple_pkt(), which internally calls
qla24xx_alloc_purex_item().
The qla24xx_alloc_purex_item() function may return a pre-allocated item
from a per-adapter pool for small allocations, instead of dynamically
allocating memory with kzalloc().
An error handling path in qla2xxx_process_purls_iocb() incorrectly uses
kfree() to release the item. If the item was from the pre-allocated
pool, calling kfree() on it is a bug that can lead to memory corruption.
Fix this by using the correct deallocation function,
qla24xx_free_purex_item(), which properly handles both dynamically
allocated and pre-allocated items. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix invalid prog->stats access when update_effective_progs fails
Syzkaller triggers an invalid memory access issue following fault
injection in update_effective_progs. The issue can be described as
follows:
__cgroup_bpf_detach
update_effective_progs
compute_effective_progs
bpf_prog_array_alloc <-- fault inject
purge_effective_progs
/* change to dummy_bpf_prog */
array->items[index] = &dummy_bpf_prog.prog
---softirq start---
__do_softirq
...
__cgroup_bpf_run_filter_skb
__bpf_prog_run_save_cb
bpf_prog_run
stats = this_cpu_ptr(prog->stats)
/* invalid memory access */
flags = u64_stats_update_begin_irqsave(&stats->syncp)
---softirq end---
static_branch_dec(&cgroup_bpf_enabled_key[atype])
The reason is that fault injection caused update_effective_progs to fail
and then changed the original prog into dummy_bpf_prog.prog in
purge_effective_progs. Then a softirq came, and accessing the members of
dummy_bpf_prog.prog in the softirq triggers invalid mem access.
To fix it, skip updating stats when stats is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Free special fields when update [lru_,]percpu_hash maps
As [lru_,]percpu_hash maps support BPF_KPTR_{REF,PERCPU}, missing
calls to 'bpf_obj_free_fields()' in 'pcpu_copy_value()' could cause the
memory referenced by BPF_KPTR_{REF,PERCPU} fields to be held until the
map gets freed.
Fix this by calling 'bpf_obj_free_fields()' after
'copy_map_value[,_long]()' in 'pcpu_copy_value()'. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: most: remove broken i2c driver
The MOST I2C driver has been completely broken for five years without
anyone noticing so remove the driver from staging.
Specifically, commit 723de0f9171e ("staging: most: remove device from
interface structure") started requiring drivers to set the interface
device pointer before registration, but the I2C driver was never updated
which results in a NULL pointer dereference if anyone ever tries to
probe it. |
| In the Linux kernel, the following vulnerability has been resolved:
backlight: led-bl: Add devlink to supplier LEDs
LED Backlight is a consumer of one or multiple LED class devices, but
devlink is currently unable to create correct supplier-producer links when
the supplier is a class device. It creates instead a link where the
supplier is the parent of the expected device.
One consequence is that removal order is not correctly enforced.
Issues happen for example with the following sections in a device tree
overlay:
// An LED driver chip
pca9632@62 {
compatible = "nxp,pca9632";
reg = <0x62>;
// ...
addon_led_pwm: led-pwm@3 {
reg = <3>;
label = "addon:led:pwm";
};
};
backlight-addon {
compatible = "led-backlight";
leds = <&addon_led_pwm>;
brightness-levels = <255>;
default-brightness-level = <255>;
};
In this example, the devlink should be created between the backlight-addon
(consumer) and the pca9632@62 (supplier). Instead it is created between the
backlight-addon (consumer) and the parent of the pca9632@62, which is
typically the I2C bus adapter.
On removal of the above overlay, the LED driver can be removed before the
backlight device, resulting in:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
...
Call trace:
led_put+0xe0/0x140
devm_led_release+0x6c/0x98
Another way to reproduce the bug without any device tree overlays is
unbinding the LED class device (pca9632@62) before unbinding the consumer
(backlight-addon):
echo 11-0062 >/sys/bus/i2c/drivers/leds-pca963x/unbind
echo ...backlight-dock >/sys/bus/platform/drivers/led-backlight/unbind
Fix by adding a devlink between the consuming led-backlight device and the
supplying LED device, as other drivers and subsystems do as well. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl818x: Fix potential memory leaks in rtl8180_init_rx_ring()
In rtl8180_init_rx_ring(), memory is allocated for skb packets and DMA
allocations in a loop. When an allocation fails, the previously
successful allocations are not freed on exit.
Fix that by jumping to err_free_rings label on error, which calls
rtl8180_free_rx_ring() to free the allocations. Remove the free of
rx_ring in rtl8180_init_rx_ring() error path, and set the freed
priv->rx_buf entry to null, to avoid double free. |
| In the Linux kernel, the following vulnerability has been resolved:
can: sun4i_can: populate ndo_change_mtu() to prevent buffer overflow
Sending an PF_PACKET allows to bypass the CAN framework logic and to
directly reach the xmit() function of a CAN driver. The only check
which is performed by the PF_PACKET framework is to make sure that
skb->len fits the interface's MTU.
Unfortunately, because the sun4i_can driver does not populate its
net_device_ops->ndo_change_mtu(), it is possible for an attacker to
configure an invalid MTU by doing, for example:
$ ip link set can0 mtu 9999
After doing so, the attacker could open a PF_PACKET socket using the
ETH_P_CANXL protocol:
socket(PF_PACKET, SOCK_RAW, htons(ETH_P_CANXL))
to inject a malicious CAN XL frames. For example:
struct canxl_frame frame = {
.flags = 0xff,
.len = 2048,
};
The CAN drivers' xmit() function are calling can_dev_dropped_skb() to
check that the skb is valid, unfortunately under above conditions, the
malicious packet is able to go through can_dev_dropped_skb() checks:
1. the skb->protocol is set to ETH_P_CANXL which is valid (the
function does not check the actual device capabilities).
2. the length is a valid CAN XL length.
And so, sun4ican_start_xmit() receives a CAN XL frame which it is not
able to correctly handle and will thus misinterpret it as a CAN frame.
This can result in a buffer overflow. The driver will consume cf->len
as-is with no further checks on this line:
dlc = cf->len;
Here, cf->len corresponds to the flags field of the CAN XL frame. In
our previous example, we set canxl_frame->flags to 0xff. Because the
maximum expected length is 8, a buffer overflow of 247 bytes occurs a
couple line below when doing:
for (i = 0; i < dlc; i++)
writel(cf->data[i], priv->base + (dreg + i * 4));
Populate net_device_ops->ndo_change_mtu() to ensure that the
interface's MTU can not be set to anything bigger than CAN_MTU. By
fixing the root cause, this prevents the buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: prevent possible shift-out-of-bounds in sctp_transport_update_rto
syzbot reported a possible shift-out-of-bounds [1]
Blamed commit added rto_alpha_max and rto_beta_max set to 1000.
It is unclear if some sctp users are setting very large rto_alpha
and/or rto_beta.
In order to prevent user regression, perform the test at run time.
Also add READ_ONCE() annotations as sysctl values can change under us.
[1]
UBSAN: shift-out-of-bounds in net/sctp/transport.c:509:41
shift exponent 64 is too large for 32-bit type 'unsigned int'
CPU: 0 UID: 0 PID: 16704 Comm: syz.2.2320 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x16c/0x1f0 lib/dump_stack.c:120
ubsan_epilogue lib/ubsan.c:233 [inline]
__ubsan_handle_shift_out_of_bounds+0x27f/0x420 lib/ubsan.c:494
sctp_transport_update_rto.cold+0x1c/0x34b net/sctp/transport.c:509
sctp_check_transmitted+0x11c4/0x1c30 net/sctp/outqueue.c:1502
sctp_outq_sack+0x4ef/0x1b20 net/sctp/outqueue.c:1338
sctp_cmd_process_sack net/sctp/sm_sideeffect.c:840 [inline]
sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1372 [inline] |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: fix validation of VF state in get resources
VF state I40E_VF_STATE_ACTIVE is not the only state in which
VF is actually active so it should not be used to determine
if a VF is allowed to obtain resources.
Use I40E_VF_STATE_RESOURCES_LOADED that is set only in
i40e_vc_get_vf_resources_msg() and cleared during reset. |
