| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB reads in rtw_get_wps_ie()
rtw_get_wps_ie() iterates over IE data from network frames without
validating that the IE header and payload fit within the remaining
buffer before reading them. Specifically:
- in_ie[cnt + 1] is read without checking cnt + 1 < in_len
- memcmp(&in_ie[cnt + 2], ...) accesses cnt + 2 without bounds check
- in_ie[cnt + 1] is used as length without verifying payload fits
Add bounds checks at the top of the loop body to break early if fewer
than 2 bytes remain for the IE header, or if the declared payload
extends past the end of the buffer. Also require at least 4 bytes of
payload before comparing the WPS OUI. |
| In the Linux kernel, the following vulnerability has been resolved:
cdrom: fix stack out-of-bounds read in CDROMVOLCTRL
mmc_ioctl_cdrom_volume() first reads the audio control mode page into a
32-byte stack buffer with cgc->buflen set to 24. If the device reports a
block descriptor, the function increases cgc->buflen to include that
descriptor and reads the page again.
For CDROMVOLCTRL, the function then builds a MODE SELECT parameter list
by moving cgc->buffer forward by offset - 8 bytes. This drops the block
descriptor from the outgoing payload and leaves a new 8-byte mode
parameter header in front of the audio control page. However, cgc->buflen
is left unchanged.
With a standard 8-byte block descriptor, cgc->buffer points at buffer + 8
but cgc->buflen remains 32. cdrom_mode_select() therefore asks the low
level packet path to write 32 bytes from that adjusted pointer, reading 8
bytes past the end of the 32-byte stack buffer.
This is not hit by CDROMVOLREAD, and CDROMVOLCTRL only triggers it on
drives that return a non-zero block descriptor length, which helps explain
why it has gone unnoticed. The overread is also sent to the device as
extra MODE SELECT payload, so it may not produce an obvious local failure.
Reduce cgc->buflen by the same amount as the buffer pointer adjustment so
the MODE SELECT transfer covers only the intended parameter list. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Fix session UAF in set_termios
rfcomm_tty_set_termios() tests dlc->session without rfcomm_mutex and
later passes the pointer to rfcomm_send_rpn(). The latter dereferences
both session->initiator and session->sock. Meanwhile, krfcommd can
unlink the DLC and free the session while holding rfcomm_mutex.
The race can proceed as follows:
TTY ioctl task krfcommd
-------------- --------
load dlc->session
enter rfcomm_send_rpn()
lock rfcomm_mutex
clear dlc->session
free session
unlock rfcomm_mutex
read session->initiator
KASAN reported:
BUG: KASAN: slab-use-after-free in rfcomm_send_rpn+0x297/0x2a0
Read of size 4 at addr ffff88810012a850 by task poc/92
Call Trace:
rfcomm_send_rpn+0x297/0x2a0
rfcomm_tty_set_termios+0x50d/0x850
tty_set_termios+0x596/0x950
set_termios+0x46a/0x6e0
tty_mode_ioctl+0x152/0xbd0
tty_ioctl+0x915/0x1240
__x64_sys_ioctl+0x134/0x1c0
Allocated by task 92:
rfcomm_session_add+0x9e/0x2e0
rfcomm_dlc_open+0x8b1/0xe00
rfcomm_dev_activate+0x85/0x1a0
rfcomm_tty_open+0x90/0x280
Freed by task 68:
kfree+0x131/0x3c0
rfcomm_session_del+0x119/0x180
rfcomm_run+0x737/0x4710
Add rfcomm_dlc_send_rpn(), which holds rfcomm_mutex while it verifies
that the DLC is still attached and sends the RPN frame. Have the TTY
path use the helper and drop its unlocked session check. This keeps the
session valid through both the frame construction and socket send. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix NULL pointer dereference in rhash table destroy
When unbinding the ath12k driver, kernel NULL pointer dereferences
occur in irq_work_sync() called from rhashtable_destroy().
Two hash tables are affected:
1. ath12k_link_sta hash table in ath12k_base
2. ath12k_dp_link_peer hash table in ath12k_dp
The issue happens because the destroy functions are called unconditionally
in cleanup paths, but the hash tables are only initialized late in their
respective init functions. If the device was never fully started or if the
init functions failed before initializing the hash tables, the pointers
will be NULL. The issues are always reproducible from a VM because the MSI
addressing initialization is failing.
Call trace for ath12k_link_sta_rhash_tbl_destroy:
RIP: irq_work_sync+0x1e/0x70
rhashtable_destroy+0x12/0x60
ath12k_link_sta_rhash_tbl_destroy+0x19/0x40 [ath12k]
ath12k_core_stop+0xe/0x80 [ath12k]
ath12k_core_hw_group_cleanup+0x6b/0xb0 [ath12k]
ath12k_pci_remove+0x60/0x110 [ath12k]
Call trace for ath12k_dp_link_peer_rhash_tbl_destroy:
RIP: irq_work_sync+0x1e/0x70
rhashtable_destroy+0x12/0x60
ath12k_dp_link_peer_rhash_tbl_destroy+0x29/0x50 [ath12k]
ath12k_dp_cmn_device_deinit+0x21/0x140 [ath12k]
ath12k_core_hw_group_cleanup+0x6b/0xb0 [ath12k]
ath12k_pci_remove+0x60/0x110 [ath12k]
Fix this by adding NULL checks before calling rhashtable_destroy() in
both destroy functions.
The NULL check approach was chosen because the rhashtable pointer
serves as the initialization state indicator. The init can fail at
various points, leaving some components uninitialized. Checking the
pointer directly is simpler than adding separate state flags that
would need synchronization. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/sdma5.2: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit ae658afc7f47f6147371ec42cc6b1a793dfdb5af) |
| The Food Menu WordPress plugin before 6.0.2 does not perform any capability or ownership check on its reservation-status update action, which is also exposed to unauthenticated users and gated only by a nonce that is publicly available to visitors, allowing unauthenticated attackers to change the status of arbitrary reservations. |
| In the Linux kernel, the following vulnerability has been resolved:
media: vivid: fix cleanup bugs in vivid_init()
When platform_device_register() fails in vivid_init(), the embedded
struct device in vivid_pdev has already been initialized by
device_initialize(), but the failure path jumps to free_output_strings
without dropping the device reference for the current platform device:
vivid_init()
-> platform_device_register(&vivid_pdev)
-> device_initialize(&vivid_pdev.dev)
-> setup_pdev_dma_masks(&vivid_pdev)
-> platform_device_add(&vivid_pdev)
This leads to a reference leak when platform_device_register() fails.
Fix this by calling platform_device_put() before jumping to the common
cleanup path.
Also, the unreg_driver label incorrectly calls
platform_driver_register() instead of platform_driver_unregister(),
which breaks cleanup when workqueue creation fails after successful
driver registration. Fix that as well.
The reference leak was identified by a static analysis tool I developed
and confirmed by manual review. The incorrect cleanup call was found
during code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
media: nuvoton: npcm-video: fix memory leaks in probe and remove
npcm_video_probe() allocates the npcm_video structure with kzalloc_obj()
but never frees it on any probe error path or in npcm_video_remove(),
leaking the allocation on every failed probe and every normal unbind.
Additionally, when npcm_video_setup_video() fails, the reserved memory
association established by of_reserved_mem_device_init() in
npcm_video_init() is not released, leaking the rmem_assigned_device
entry on the global list.
Fix both by adding kfree(video) to all probe error paths and to
npcm_video_remove(), and adding the missing
of_reserved_mem_device_release() call when npcm_video_setup_video()
fails. |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-fwnode: Fix subdev owner overwritten in v4l2_async_register_subdev_sensor()
The v4l2 helper v4l2_async_register_subdev_sensor() calls
v4l2_async_register_subdev(), which is a macro that expands to
__v4l2_async_register_subdev(sd,THIS_MODULE). Since the macro is expanded
inside v4l2-fwnode.c, THIS_MODULE resolves to the v4l2-fwnode module
rather than the sensor driver module that originally set sd->owner. When
v4l2-fwnode is built-in, THIS_MODULE evaluates to NULL, which then
overwrites the sensor driver's owner with NULL.
This causes the problem that the sensor module's reference count is never
incremented during async registration, so the module can be removed while
the subdevice is still in use by a notifier (e.g., a CSI-2 receiver
bridge driver).
Fix this by renaming v4l2_async_register_subdev_sensor() to
__v4l2_async_register_subdev_sensor() with an added explicit module
argument and introducing a wrapper macro:
#define v4l2_async_register_subdev_sensor(sd) \
__v4l2_async_register_subdev_sensor(sd, THIS_MODULE)
This ensures the sensor driver module is properly referenced even when
the sensor driver does not init the owner field before calling
v4l2_async_register_subdev_sensor() and prevents premature module removal. |
| In the Linux kernel, the following vulnerability has been resolved:
media: pci: dm1105: Free allocated workqueue
Destroy allocated workqueue in remove() callback to free its resources,
thus fixing memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
media: nxp: imx8-isi: Add missing v4l2_subdev_cleanup() in crossbar and pipe
Both mxc_isi_crossbar_init() and mxc_isi_pipe_init() call
v4l2_subdev_init_finalize() which allocates the subdev active state,
but neither mxc_isi_crossbar_cleanup() nor mxc_isi_pipe_cleanup()
calls v4l2_subdev_cleanup() to free it.
This causes a memory leak on every rmmod, reported by kmemleak:
unreferenced object 0xffff0000d06fc800 (size 192):
comm "(udev-worker)", pid 254, jiffies 4294913455
backtrace (crc 36eeae58):
kmemleak_alloc+0x34/0x40
__kvmalloc_node_noprof+0x5f8/0x7d8
__v4l2_subdev_state_alloc+0x1fc/0x30c
__v4l2_subdev_init_finalize+0x178/0x368
Add the missing v4l2_subdev_cleanup() calls before media_entity_cleanup()
in both crossbar and pipe cleanup paths. |
| In the Linux kernel, the following vulnerability has been resolved:
media: meson: vdec: Fix memory leak in error path of vdec_open
The vdec_open() function previously jumped directly to
err_m2m_release when vdec_init_ctrls() failed, skipping
release of the m2m context. This caused a resource leak.
Fix it by introducing a proper err_m2m_ctx_release label
that calls v4l2_m2m_ctx_release(sess->m2m_ctx) before
releasing the m2m device.
This was identified via kmemleak:
unreferenced object 0xffff0000205d6878 (size 8):
comm "v4l_id", pid 5289, jiffies 4294938580
hex dump (first 8 bytes):
40 d2 49 18 00 00 ff ff @.I.....
backtrace (crc d3204599):
kmemleak_alloc+0xc8/0xf0
__kvmalloc_node_noprof+0x60c/0x850
v4l2_ctrl_handler_init_class+0x1b4/0x2e8 [videodev]
vdec_open+0x1f4/0x788 [meson_vdec]
v4l2_open+0x144/0x460 [videodev]
chrdev_open+0x1ac/0x500
do_dentry_open+0x3f0/0xfe8
vfs_open+0x68/0x320
do_open+0x2d8/0x9a8
path_openat+0x1d0/0x4f0
do_filp_open+0x190/0x380
do_sys_openat2+0xf8/0x1b0
__arm64_sys_openat+0x13c/0x1e8
invoke_syscall+0xdc/0x268
el0_svc_common.constprop.0+0x178/0x258
do_el0_svc+0x4c/0x70 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Shut down BO cache timer before teardown
The BO cache timer callback schedules time_work, and time_work can rearm
the timer through vc4_bo_cache_free_old().
vc4_bo_cache_destroy() deletes the timer and then cancels the work, which
does not break that cycle: the work being cancelled can rearm the timer,
and the timer then queues work again after teardown.
Use timer_shutdown_sync() instead, so the timer cannot be rearmed and the
cycle ends with cancel_work_sync(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: fix indefinite fence wait during GPU reset
pre_reset only force-completes fences of MAPPED queues. A queue in any
other state (e.g. mid-eviction) keeps its last_fence pending; after a
GPU reset that fence never signals, so the eviction/suspend worker and
process teardown (amdgpu_evf_mgr_flush_suspend) wait on it forever and
wedge the machine:
INFO: task kworker/6:28 blocked for more than 120 seconds.
Workqueue: events amdgpu_eviction_fence_suspend_worker [amdgpu]
Call Trace:
dma_fence_wait_timeout+0x7e/0x130
amdgpu_userq_evict+0x67/0x140 [amdgpu]
amdgpu_eviction_fence_suspend_worker+0xd8/0x160 [amdgpu]
process_scheduled_works+0xa6/0x420
Force-complete every queue's fence regardless of state. The unmap and
mark-hung step stays gated on MAPPED, since unmapping a queue that is
not mapped is invalid.
(cherry picked from commit 9102b39fa924dcc3dc75a3137bfa9633c40b88c0) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Release VFCT ACPI table reference
amdgpu_acpi_vfct_bios() fetches the VFCT table with acpi_get_table()
but never releases it. acpi_get_table() takes a reference on the
table (incrementing its validation_count and mapping it on the 0->1
transition); without a paired acpi_put_table() the mapping is leaked
on every call, whether or not a matching VBIOS image is found.
Route all exit paths after the table is acquired through a common
acpi_put_table(). The VBIOS image is copied out with kmemdup() before
the table is released, so it remains valid for the caller.
(cherry picked from commit ca5988682b4cba4cd125a0fa99b2de1239164ae4) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx11: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit daa62107452d2451787c4248ca38fa2d1a0cbefd) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/sdma5.0: replace BUG_ON() with WARN_ON()
There's no need to crash the kernel for these cases.
(cherry picked from commit 8d144a0eb09537055841af48c9e7c2d4cd48e84d) |
| In the Linux kernel, the following vulnerability has been resolved:
media: stm32-dcmipp: Return queued buffers on start_streaming() failure
The vb2 framework hands buffers to the driver via buf_queue() before
calling start_streaming(). If start_streaming() returns an error
without first returning those buffers via vb2_buffer_done(),
vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued
buffers leak.
dcmipp_bytecap_start_streaming() returned -EINVAL when the source
subdevice could not be resolved from the media graph, before
pm_runtime_resume_and_get() and media_pipeline_start() had been called.
The remaining error paths already converge on the err_buffer_done
label, which calls dcmipp_bytecap_all_buffers_done(...,
VB2_BUF_STATE_QUEUED). Jump to that label directly: the intermediate
err_pm_put / err_media_pipeline_stop labels are skipped, which is
correct because nothing they would undo has happened yet.
This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo:
Return queued buffers on start_streaming() failure"). |
| In the Linux kernel, the following vulnerability has been resolved:
media: saa7134: Fix a possible memory leak in saa7134_video_init1
In saa7134_video_init1(), the return value of the first
saa7134_pgtable_alloc() is not checked. If it fails, the function
continues as if successful, leaving the driver with an invalid page
table. Additionally, if vb2_queue_init() for the VBI queue fails after
the video queue page table has been allocated, the allocated memory is
not freed before returning. The second saa7134_pgtable_alloc() also
lacks a return value check. Errors occur during device probing before
the device is fully registered, the normal cleanup path in
saa7134_finidev() is not executed, leading to memory leaks and
potential use of uninitialized DMA resources.
Check the return value of both saa7134_pgtable_alloc() calls and
propagate errors. On failure of any later step, free allocated page
tables to avoid memory leaks. Ensure control handlers are also
released on error to prevent further resource leakage.
Found by code review. |
| In the Linux kernel, the following vulnerability has been resolved:
media: radio-si476x: Unregister v4l2_device on probe failure
si476x_radio_probe() registers radio->v4l2dev before allocating the V4L2
controls and before registering the video device. If any of those later
steps fails, probe returns through the exit label after freeing only the
control handler.
A failed probe does not call si476x_radio_remove(), so the
v4l2_device_unregister() there is not reached. This leaves the parent
device reference taken by v4l2_device_register() behind on the error path.
Unregister the V4L2 device in the probe error path after freeing the
controls. |
