| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In Modem, there is a possible out of bounds read due to a missing bounds check. This could lead to remote denial of service, if a UE has connected to a rogue base station controlled by the attacker, with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: MOLY00741071; Issue ID: MSV-7620. |
| In display, there is a possible information disclosure due to a missing bounds check. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11004276; Issue ID: MSV-7757. |
| In display, there is a possible information disclosure due to an integer overflow. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11004274; Issue ID: MSV-7749. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an out-of-bounds read. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to obtain sensitive information or cause a denial of service due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Prevent access to unsupported weight registers
Sashiko reports:
During initialization of the nct6116 chip, the driver sets data->pwm_num
to 5. However, it assigns several NCT6106 register arrays (such as
NCT6106_REG_WEIGHT_DUTY_STEP, NCT6106_REG_WEIGHT_TEMP_SEL, and
NCT6106_REG_WEIGHT_TEMP_*) to data->REG_PWM and data->REG_WEIGHT_TEMP.
These arrays only contain 3 elements.
In nct6775_update_pwm(), the driver iterates up to data->pwm_num. If
data->has_pwm has bits 3 or 4 set (which is structurally possible for
nct6116), the loop attempts to read elements at index 3 and 4 from these
3-element arrays. This results in a global out-of-bounds read, which can
be caught by KASAN.
Furthermore, the driver uses these garbage out-of-bounds values as
hardware register addresses for subsequent read and write operations. This
leads to invalid hardware register access, potentially causing hardware
misconfiguration or system crashes.
The underlying problem is that the chip does support up to five fan
control channels, but only the first three support weight control.
Fix the problem by extending the affected weight register arrays with
zeroed fields. The driver uses zeroed register addresses to determine
if a register is supported or not, and skips accesses for unsupported
registers. |
| In the Linux kernel, the following vulnerability has been resolved:
macsec: don't read an unset MAC header in macsec_encrypt()
macsec_encrypt() reads the Ethernet header via eth_hdr(skb)
(skb->head + skb->mac_header) to memmove() the 12 source/destination MAC
bytes forward and make room for the SecTAG.
On the AF_PACKET SOCK_RAW + PACKET_QDISC_BYPASS transmit path the skb
reaches the macsec ndo_start_xmit() with the MAC header unset, so
eth_hdr(skb) resolves to skb->head + (u16)~0 and the read is out of
bounds: a 12-byte heap over-read that is also emitted on the wire as the
frame's outer source/destination MAC. KASAN reports a slab-out-of-bounds
read in macsec_start_xmit() on 6.0; on current mainline a CONFIG_DEBUG_NET
build flags it as an unset mac header in skb_mac_header().
On the TX path the L2 header is at skb->data, so use skb_eth_hdr(), added
by commit 96cc4b69581d ("macvlan: do not assume mac_header is set in
macvlan_broadcast()") for exactly this purpose. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an off-by-one error in bounds checking. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: bound get_version reply decode to front len
handle_get_version_reply() uses msg->front_alloc_len as the decode
boundary for MON_GET_VERSION_REPLY. That is the size of the reused
reply buffer, not the number of bytes actually received.
A truncated reply can therefore pass ceph_decode_need() and decode the
second u64 from stale tail bytes left in the buffer by an earlier
message, causing an uninitialized memory read.
Use msg->front.iov_len as the receive-side decode boundary, matching
other libceph reply handlers and limiting decoding to the bytes that
were actually read from the wire. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to obtain sensitive information due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: bound element ID read when checking non-inheritance
cfg80211_is_element_inherited() reads the first data octet of the
candidate element (id = elem->data[0]) to look it up in an extension
non-inheritance list. It does so after testing elem->id, but without
verifying that the element actually has a data octet. A zero-length
extension element (WLAN_EID_EXTENSION with length 0) therefore makes it
read one octet past the end of the element.
_ieee802_11_parse_elems_full() runs this check for every element of a
frame once a non-inheritance context exists -- e.g. while parsing a
per-STA profile of a Multi-Link element in a (re)association response,
or a non-transmitted BSS profile -- so a crafted frame from an AP can
trigger a one-octet slab-out-of-bounds read during element parsing:
BUG: KASAN: slab-out-of-bounds in cfg80211_is_element_inherited
Read of size 1 ... in net/wireless/scan.c
Return early (treat the element as inherited) when an extension element
carries no data, mirroring the existing handling of empty ID lists.
The bug was found by fuzzing ieee802_11_parse_elems_full() under KASAN. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: at76c50x-usb: avoid length underflow in at76_guess_freq()
at76_guess_freq() checks only that the received frame is at least a bare
802.11 header (24 bytes) before subtracting the fixed management-body
offset:
len -= el_off;
For both beacon and probe response frames, el_off is 36. If the frame is
shorter than el_off, subtracting it causes the calculated IE length to
wrap. The length is eventually passed to cfg80211_find_elem_match() as a
very large unsigned value, so the element walk runs beyond the RX skb.
This path is reached from at76_rx_tasklet() while scanning. If the device
delivers a truncated beacon or probe response, the oversized IE length
causes an out-of-bounds read during scanning.
Skip the IE lookup if the frame does not reach the variable elements,
before subtracting el_off. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_ncm: validate datagram bounds in ncm_unwrap_ntb()
When unpacking host-supplied NTBs, ncm_unwrap_ntb() checks datagram length
against frame_max but does not verify that the datagram fits within the
declared block length. Additionally, when decoding multiple NTBs from a
single socket buffer, subsequent block lengths are not checked against the
actual remaining buffer data.
With these checks missing, a malicious USB host can specify datagram
offsets and lengths that point beyond the block, or supply secondary NTB
headers declaring lengths larger than the buffer. skb_put_data() then
copies adjacent kernel memory from skb_shared_info into the network skb.
Fix this by verifying that sufficient buffer space remains for the NTB
header before parsing, handling zero-length block declarations, ensuring
that block lengths never exceed the remaining buffer space, and verifying
that each datagram payload stays strictly within the block boundary. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uvc: clamp SEND_RESPONSE length to the response buffer
uvc_send_response() builds the UVC control response from a user-supplied
struct uvc_request_data:
req->length = min_t(unsigned int, uvc->event_length, data->length);
...
memcpy(req->buf, data->data, req->length);
req->length is clamped to uvc->event_length, which is taken from the
host control request wLength (up to UVC_MAX_REQUEST_SIZE, 64), and to
data->length, which comes from the UVCIOC_SEND_RESPONSE ioctl and is
only checked for being negative. The source buffer data->data is only
60 bytes, so a response with uvc->event_length and data->length both
greater than 60 makes memcpy() read past the end of data->data.
Clamp req->length to sizeof(data->data) as well. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: fix OOB read from firmware num_msg in TX complete handler
The firmware-controlled num_msg field (u8, 0-255) drives the loop in
ath6kl_wmi_tx_complete_event_rx() without validation against the buffer
length. This allows out-of-bounds reads of up to 1020 bytes past the
WMI event buffer when the firmware sends an inflated num_msg.
Add a check that the buffer is large enough to hold the fixed struct
and the num_msg variable-length entries. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: carl9170: bound memcpy length in cmd callback to prevent OOB read
When the firmware sends a command response with a length mismatch,
carl9170_cmd_callback() logs the mismatch and calls carl9170_restart()
but then falls through to memcpy(ar->readbuf, buffer + 4, len - 4).
Since len comes from the firmware and can exceed ar->readlen, this
copies more data than the readbuf was allocated for.
Bound the memcpy to min(len - 4, ar->readlen) so that the response
is still completed -- avoiding repeated restarts from queued garbage --
while preventing an overread past the response buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: carl9170: fix OOB read from off-by-two in TX status handler
The bounds check in carl9170_tx_process_status() uses
`i > ((cmd->hdr.len / 2) + 1)` which is off by two, allowing
2 extra iterations past valid _tx_status entries when the firmware-
controlled hdr.ext exceeds hdr.len/2. Fix by using the correct
comparison `i >= (cmd->hdr.len / 2)`. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: occ: validate poll response sensor blocks
The OCC poll response parser walks a counted list of sensor data blocks.
It used the static backing-array capacity as the parse boundary, but a
transport response makes only data_length bytes current and valid. A
truncated response can therefore make the parser consume a block header or
block extent outside the current response.
Use data_length as the parent boundary, prove the fixed poll header and
each current block header before reading them, and prove the complete block
before advancing. Keep parsed sensor metadata local until the complete
response has passed validation, then publish it. Propagate
malformed-response errors before publishing the OCC as active. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: bound uAP association event IEs to the event buffer
mwifiex_process_uap_event() handles EVENT_UAP_STA_ASSOC by exposing the
(re)association request IEs that the firmware copies into the event:
sinfo->assoc_req_ies = &event->data[len];
len = (u8 *)sinfo->assoc_req_ies - (u8 *)&event->frame_control;
sinfo->assoc_req_ies_len = le16_to_cpu(event->len) - (u16)len;
event->len is supplied by the device firmware and is never validated,
and the subtraction is unchecked. assoc_req_ies points into
adapter->event_body[MAX_EVENT_SIZE], a fixed-size array embedded in the
kmalloc()'d struct mwifiex_adapter.
On the ap_11n_enabled path mwifiex_set_sta_ht_cap() walks these IEs with
cfg80211_find_ie(), whose for_each_element() loop dereferences each
element header. A firmware-reported event->len larger than the bytes
actually received makes assoc_req_ies_len describe IEs that extend past
event_body, so the walk reads out of the adapter slab object, a
slab-out-of-bounds read (KASAN: slab-out-of-bounds in cfg80211_find_ie).
An event->len smaller than the header instead makes the int subtraction
negative, which wraps to a huge size_t when stored in assoc_req_ies_len.
The same length is handed to cfg80211_new_sta(), so a more modest
over-claim can also copy stale event_body bytes into the
NL80211_CMD_NEW_STATION notification.
A malicious or malfunctioning mwifiex device (USB/SDIO/PCIe) can deliver
such an event while the interface is in AP/uAP mode.
Validate event->len before use: reject a length that underflows the
header or that would place the IEs outside the event_body[] buffer the
event was copied into. event->len here is struct mwifiex_assoc_event.len,
a payload field internal to this event, not the transport frame length,
so it is validated in this handler rather than at the generic
MWIFIEX_TYPE_EVENT receive path, which only sees the event cause and the
transport frame length. The bound is against event_body[MAX_EVENT_SIZE]
rather than the actually-received length because the transports store the
event differently (USB and SDIO leave the 4-byte event header in
event_skb, PCIe strips it via skb_pull), whereas event_body is the single
fixed buffer all of them copy the event into. This is the event-path
analogue of the receive-path bounds checks added in commit 119585281617
("wifi: mwifiex: Fix OOB and integer underflow when rx packets"). |
| In the Linux kernel, the following vulnerability has been resolved:
media: cedrus: skip invalid H.264 reference list entries
Cedrus consumes H.264 ref_pic_list0/ref_pic_list1 entries from the
stateless slice control and later uses their indices to look up
decode->dpb[] in _cedrus_write_ref_list().
Rejecting such controls in cedrus_try_ctrl() would break existing
userspace, since stateless H.264 reference lists may legitimately carry
out-of-range indices for missing references. Instead, guard the actual
DPB lookup in Cedrus and skip entries whose indices do not fit the fixed
V4L2_H264_NUM_DPB_ENTRIES array.
This keeps the fix local to the driver use site and avoids out-of-bounds
reads from malformed or unsupported reference list entries. |
